Leitura livre · conta gratuita para contribuirSucessor do Anticars (2000)

Porsche 928

1977–1995 · 1 gerações · 0 defeitos documentados · 2 mercados
Gerações
Todas as gerações9281977–19951832
Ano do modelo
MercadoTodosJPNA
RecallCríticoOutroJP

その他(その他)

音響機器のオーディオ本体(メーカー:ソニー(株)、型式:XR-5H911,XRー5H912)の配 線基板において、当該基板の製造工程が不適切なため、コンデンサーが損傷しているもの があり、そのままの状態で使用を続けると、当該コンデンサーの端子間が短絡して、スピ ーカーに過大な電流が流れ発熱し、最悪の場合、火災に至るおそれがある。

MLIT · Japão7 de dez. de 19991207700Anos-modelo 1990–1991Exibido no japonês original · tradução pendenteVer detalhes →
RecallCríticoElétricaJP

その他(その他)

音響機器のオーディオ本体の配線基盤において、当該基盤の製造工程が不適切なため、コ ンデンサが損傷しているものがあり、そのままの状態で使用を続けると、当該コンデンサ の端子間が短絡して、スピーカーに過大な電流が流れ、最悪の場合、火災にいたるおそれ がある。

MLIT · Japão19 de dez. de 19971206650Anos-modelo 1990–1995Exibido no japonês original · tradução pendenteVer detalhes →
RecallCríticoMotorNA

Fuel System

The fuel gauge sending unit mounting nut may crack and, under certain fuel level and operational conditions, result in fuel tank leakage. Leaking fuel could ignite on the hot exhaust system and result in a vehicle fire. Correction: Mounting nuts will be inspected and replaced as required.

Transport Canada14 de jun. de 19901990089Anos-modelo 1990Exibido no inglês original · tradução pendenteVer detalhes →
RecallCríticoMotorNA

Engine

The heatshield above the catalytic converter is inadequate under certain circumstances involving engine malfunction. A misfiring engine could overheat the catalytic converter causing materials in the vicinity of the converter, including the automatic transmission fluid lines to ignite resulting in an underbody fire. Correction: 1) replace the heatshiel with a larger improved heatshield. 2) install a heat resistant sleeve on atf lines where necessary. 3) replace plastic atf line mounting bracket in proximity to the catalytic converter with a metal mounting bracket.

Transport Canada28 de jun. de 19891989091Anos-modelo 1985–1987Exibido no inglês original · tradução pendenteVer detalhes →
RecallCríticoMotorNA

Fuel System

Lack of ozone resistance in the fuel return hoses may cause cracking of the fuel line. This could result in fuel leakage and engine compartment fire. Correction: Fuel return hoses will be replaced.

Transport Canada16 de mar. de 19871987033Anos-modelo 1987Exibido no inglês original · tradução pendenteVer detalhes →
RecallCríticoMotorNA

Recall

A brazed joint on the metal fuel line may leak and result in a vehicle fire.

Transport Canada18 de fev. de 19801980020Anos-modelo 1980Exibido no inglês original · tradução pendenteVer detalhes →
RecallModeradoCâmbioNA

Powertrain

A filler piece with insuffient support was installed in the automatic transmission. This piece can move and inhibit the kickdown function. This could result in an accident during overtaking.

Transport Canada6 de ago. de 19921992091Anos-modelo 1991Exibido no inglês original · tradução pendenteVer detalhes →
RecallModeradoCâmbioNA

Power train:Automatic transmission

A plastic filler piece located in the automatic transmission was installed without sufficient support. This filler piece can move because of the hydraulic pressure in the system, and not allow the automatic transmission to kick down to a lower gear.

NHTSA · Estados Unidos3 de ago. de 199292V092000Anos-modelo 1991Exibido no inglês original · tradução pendenteVer detalhes →
RecallModeradoSuspensãoNA

Recall

Vehicles were equipped with an engine carrier which has a faulty weld to the support bracket. If the weld were to give way, a break in the engine carrier could develop, resulting in a steering blockage and possible loss of vehicle control.

Transport Canada9 de jul. de 19851985082Anos-modelo 1985Exibido no inglês original · tradução pendenteVer detalhes →
RecallModeradoMotorNA

Engine and engine cooling:Engine

The engine carrier has a faulty weld to the support bracket eyes. Consequence of defect: The weld could give way and the bracket eye separate from the carrier. With higher mileage accumulation a break in the engine carrier could develop and result in a steering blockage, loss of control with possibly an accident.

NHTSA · Estados Unidos1 de jul. de 198585V084000Anos-modelo 1985Exibido no inglês original · tradução pendenteVer detalhes →
RecallModeradoFreiosNA

Recall

The front brake hoses may have been incorrectly routed during production.If this occurred,the brake hose could rub against the rim at certain road wheel postions and eventually wear through

Transport Canada22 de jul. de 19821982063Anos-modelo 1982Exibido no inglês original · tradução pendenteVer detalhes →
RecallModeradoSuspensãoNA

Recall

The univesal joint connecting the steering shaft to the steering rack may be improperly positioned. If the vehicle is driven on rough roads for an extended period of time the connection could loosen an cause excessive steering wheel free play.

Transport Canada22 de jul. de 19821982062Anos-modelo 1980Exibido no inglês original · tradução pendenteVer detalhes →
RecallModeradoFreiosNA

Service brakes, hydraulic:Foundation components:Hoses, lines/piping, and fittings

Due to the improper installation of hydraulic brake hoses, the hose could rub against the rim in certain wheel positions. Brake fluid loss could result, causing a degradation in the performance of the front brake system. This would cause an increase in vehicle stopping distances.

NHTSA · Estados Unidos12 de mai. de 198282V049000Anos-modelo 1982Exibido no inglês original · tradução pendenteVer detalhes →
RecallModeradoSuspensãoNA

Steering: Steering wheel/handle bar

On the involved vehicles, the universal joint which connects the steering shaft to the steering rack may have been improperly positioned during assembly. If vehicle is driven on poor roads for an extended period of time, the connection between the steering shaft and universal joint could loosen and cause excessive steering wheel free play.

NHTSA · Estados Unidos12 de mai. de 198282V048000Anos-modelo 1980Exibido no inglês original · tradução pendenteVer detalhes →
RecallModeradoSuspensãoNA

Suspension:Front:Shock absorber

Front shock absorbers on some vehicles may have improperly welded mounting eyes. The shock absorber mounting could separate and cause the suspension to collapse if vehicle is driven on rough roads for a long period of time.

NHTSA · Estados Unidos25 de mar. de 198181V040000Anos-modelo 1980–1981Exibido no inglês original · tradução pendenteVer detalhes →

Fontes: NHTSA (Estados Unidos, domínio público), Transport Canada (Open Government Licence – Canada), DVSA (Reino Unido, Open Government Licence v3.0), RappelConso e Safety Gate da UE (França, Licence Ouverte 2.0), MLIT (Japão, Licença de Dados Públicos 1.0) e MOLIT (Coreia do Sul, car.go.kr).