Roof side rail airbag may deploy incorrectly
A roof side rail air bag may not deploy as intended
🔔 Crie uma conta gratuita para receber alertas por e-mail sobre Vauxhall Nova Corsa E
A roof side rail air bag may not deploy as intended
There is the possibility of water penetration into the vent hose resulting in water ingress into the vacuum pump over the wire harness and into the relay box. In the worst case a short circuit may lead to a risk of fire.
null Water can penetrate into the connector of the relay box located on the electronic vacuum pump causing a short circuit which could lead to a fire.
Water ingress to the relay on the electrical vacuum pump may cause a short. In extreme instances this may lead to fire.
The gears within the steering rack may not have been manufactured to the correct specification which may allow them to crack over a period of time. Prolonged use could cause loss of steering control.
A small number of steering knuckles on hub swivels have been manufactured incorrectly. In time these knuckles might fail with the attendant loss of directional control of the vehicle.
THE MANUFACTURER HAS RECOMMENDED THAT AFFECTED VEHICLES ARE NOT DRIVEN UNTIL CHECKED BY THEIR OFFICIAL AGENTS. The steering system may not have been produced according to specification. There is a risk that the steering intermediate shaft may break while driving resulting in the loss of steering control.
There could be an unexpected loss of braking performance due to the ABS/ESP Modulator not being correctly filled with hydraulic oil at the factory.
It has been identified that due to a manufacturing deviation the base material for the telescopic tube of the intermediate steering shaft may lack the required rigidity. This may lead to breakage of the shaft which in the worst case would lead to loss of steering control.
It has been identified that the above vehicles could be affected by moisture ingress at the ABS connector. The moisture can enter through the ground wiring connection which can lead to the ABS not functioning correctly overheating within the connector and in extreme cases a fire.
Vehicles may be affected by incorrect performance of the On-Board-Diagnostics related to Selective Catalytic Reduction system and/or Diesel Particle Filter. The Malfunction Indicator Light (MIL) may not illuminate in the event of a malfunction and therefore does not comply with emission regulations.
Affected vehicles may exceed regulatory emission standards
On affected vehicles the AC compressor stator wiring could develop a fault leading to current loss inside the AC compressor that could result in a vehicle powertrain shutdown when driving.
Software does not allow the authorities to test according to regulation.
The customer might not be alerted to a malfunction of the turn indicator.
A potential for an intermittent internal connection issue on the DC/DC chip of the on-board charger.
On affected vehicles certain seat belts might stick when pulled out and retracted.
lambda control may result in NOx limit being exceeded during the vehicle lifetime.
Unexpected opening of the hood while driving.
Due to a possible contamination of the tooth segment the handbrake pawl may not latch correctly. This may cause the handbrake to disengage.
Due to a manufacturing process deviation the toothed rack of the steering gear might break under extensive force application i.e. when manoeuvring at slow speed.
The connection between the steering knuckle and the lower control arm may not be assembled correctly. If this condition is evident the connection could become insecure. The event can happen suddenly and unexpectedly in which case the vehicle is no longer controllable.
Er kan scheurvorming in de tandheugel van de stuurinrichting ontstaan. Hierdoor kan de tandheugel breken.
Het materiaal dat gebruikt is voor de fabricage van de stuurkolomtussenas voldoet niet aan de voorgeschreven specificaties. Hierdoor is de sterkte van de stuurkolomtussenas onvoldoende.
It has been identified that on a certain number of 2007 model year vehicles the front lower suspension control arms might fracture near the bushing due to a production deviation during the welding process. The control arm may then lack rigidity; which may impair driving stability. In the worst case the driver may loose control of the vehicle.
Fontes: NHTSA (Estados Unidos, domínio público), Transport Canada (Open Government Licence – Canada), DVSA (Reino Unido, Open Government Licence v3.0), RappelConso e Safety Gate da UE (França, Licence Ouverte 2.0), MLIT (Japão, Licença de Dados Públicos 1.0) e MOLIT (Coreia do Sul, car.go.kr).