General Motors LLC (GM) is recalling certain 2018 Buick Regal vehicles. During the manufacturing process, the rear seat belts may have been improperly routed around the bolster bracket on the rear outboard seats, which can cause inadequate restraint of the passengers.
General Motors LLC (GM) is recalling certain model year 2011 Buick Regal vehicles manufactured November 3, 2009, to March 25, 2011, equipped with 8-way power adjustable front seats. The power seat wiring harness may contact the seat frame, causing the wires to chafe.
Vehicle description: Certain passenger vehicles, equipped with sunvisor located air bag labels, fail to conform to federal motor vehicles safety standard no. 208, "occupant crash protection." these vehicles have a message area less than 30 cm which does not meet the requirements of the standard.
Vehicle description: Passenger vehicles. Some of these vehicles exhibit a condition in which the driver side impact air bag inflator separates from the air bag module during deployment.
Left handed driver's side shoulder belt anchor plate may be upside down in lock pillar so that the unthreaded slot of the plate aligned with the hole in the lock pillar. This resulted in the anchor bolt being driven into the slot instead of the threaded hole of the anchor plate. Consequence of defect: In a vehicle crash, belt anchor bolt may pull loose from anchor plate, thus failing to comply with fmvss 210, seat belt assembly anchorages, and increases likelihood of injury to occupant.
General Motors LLC (GM) is recalling certain model year 2011-2012 Buick LaCrosse, Regal and Chevrolet Camaro, as well as certain 2010-2012 Cadillac SRX, Chevrolet Equinox and GMC Terrain vehicles, equipped with power height adjustable driver and passenger seats. In the affected vehicles, the bolt that secures the driver's and passenger's power front seat height adjuster may fall out causing the seat to drop suddenly to the lowest vertical position.
Vehicle description: Passenger vehicles, light duty trucks, sport utility vehicles, and mini vans equipped with trw seat belt buckle assemblies. The buckle base of these seat belt assemblies were not properly heat treated and therefore do not pass the load bearing requirement of federal motor vehicle safety standard no. 209, "seat belt assemblies."
Certain vehicles may have a centre rear seatbelt anchor plate which exhibits stress cracks. In the event of a vehicle crash, the seatbelt system may fracture and injury to the seat occupant could occur. Correction: Centre rear seat belt system will be replaced.
The driver and passenger front seat manual reclining mechanisms do not comply with the requirements of fmvss 207, "seating systems." the seat back mechanisms will not latch under certain conditions.
Certain vehicles may not comply with CMVSS 207 - Anchorage of Seats. Front seat back recliner mechanism may not latch properly. Correction: Driver and passenger front seat back recliner machanisms will be replaced.
Certain vehicles do not comply with CMVSS 208 - Seatbelt Installations. Front door shoulder belt guide loops may not provide front seat occupants with proper protection in the event of a crash. Correction: Dealers will inspect the front door shoulder belt guide loops for possible cracks. If a cracked guide loop is found, both front door guide loops will have reinforcing plates installed.
On certain vehicles, the front shoulder seat belt webbing may separate at the seat belt upper guide loops (driver and/or passenger side). Separation of the webbing would occur without prior warning and could increase the risk of injury to belted front outboard occupants in the event of a crash. Correction: Dealers will install a controlled rotation bracket on both the driver and passenger side front seat shoulder belt guide loops to prevent this condition from occuring.
Certain vehicles do not comply with CMVSS 210 - Seatbelt Assembly Anchorages. Anchor bolt may pull through the upper anchorage plate. Correction: Nut assembly with a larger diameter flanged nut will be installed in place of the existing nut assembly.
Certain vehicles equipped with hatchroof option may not comply with CMVSS 210 - Seatbelt Assembly Anchorages. Drivers side shoulder belt anchor plate may be located upside down which can result in the anchor bolt pulling loose in an accident.
On certain vehicles, the heads of the rear seatbelt anchor bolts may break off during normal vehicle use and in the event of an accident in which the rear seatbelts are in use, the probability of injury to the wearer will be increased.
Some vehicles have bucket seat back locks that do not conform to federal motor vehicle safety standard 207, anchorage of seats. In event of a crash, the seat back lock may not function.