Steering: Steering wheel/handle bar
The zinc plating operation performed on the upper steering column shaft coupling bolt caused hydrogen embrittlement and breakage of the bolt.
🔔 注册免费账户,接收 Chrysler LeBaron (所有代) 的邮件提醒
The zinc plating operation performed on the upper steering column shaft coupling bolt caused hydrogen embrittlement and breakage of the bolt.
A steering column coupling bolt may fracture due to hydrogen embrittlement, causing loss of clamping load on the steering column shaft coupling with resultant loss of steering control. Correction: Zinc plated steering column coupling bolts will be replaced with a phosphate coated bolt.
Air bag inflator modules may not contain diffuser holes between the ignitor and propellant chambers.
发动机气门盖垫片可能会脱位,导致发动机油泄漏。
搭载2.2升或2.5升EFI(非涡轮增压)发动机的车辆,气门室垫片可能漏油,可能导致发动机舱火灾。更正:气门室盖垫片将更换为改良版盖板,并以RTV密封剂替代垫片。
Fuel leakage may occur in low ambient temperature operation at connections of an engine compartment fuel supply hose to the pressure regulator and to the fuel rail.
A resister in the instrument cluster may be subjected to an electrical current overload due to failure of a switching transister.The overheated resister could possibly start a fire in the instrument panel.
A resistor in the electronic panel cluster may be subjected to an electrical current overload due to failure of a switching transistor. Consequence of defect: The overheated resistor could ignite and start an instrument panel fire.
On certain vehicles equipped with a 2.2 Litre turbo engine, an inadequately tightened fuel hose clamp at the fuel system pressure regulator could result in fuel leakage and provide the potential for an engine compartment fire.
An engine compartment fuel hose routed to the fuel system pressure regulator may have an inadequately tightened hose clamp. Consequence of defect: The fuel hose could leak and result in an engine compartment fire.
The potential for fuel leakage exists in the engine compartment at the fuel reservoir seam and its hose connections. The fuel reservoir is a silver colored can mounted to the air cleaner.
On certain vehicles, hydraulic brake tube may interfere with exhaust system hangar bolt and eventually result in brake fluid leakage. This could create a partial loss of braking capability. Should this occur the brake warning light on the instrument panel will warn driver.
Hydraulic brake tube routing to the rear wheels may alloow interference between the tube and the rear park brake cable. Resulting abrasion could cause tube failure and partial loss of braking capability. The instrument panel light will provide warning of the partial loss.
这些车辆可能不符合 C.M.V.S.S 207 标准——座椅固定装置。部分配备桶形座椅的车辆上,行进座椅卡扣锁杆(安全带固定点)的强度可能不足,可能无法满足该标准的静态载荷要求。纠正措施:更换锁杆总成。
An improperly adjusted hood latch assembly could prevent engagement of the secondary latching mechanism. In such a case the secondary latch would not function to restrain the hood in the event that the primary latch was not engaged for any reason and hood fly-up could occur, blocking the driver's vision. Correction: Secondary hood latch will be inspected and adjusted if necessary, to ensure proper engagement.
The hood latch assembly may not have been properly installed and the secondary hood latch may be prevented from engaging when the hood is closed.
In areas of high road salt use, vehicles may experience a bonded disc brake pad separation from the front or rear brake plates. This could cause a reduction in brake performance and a possible vehicle crash. Correction: Bonded disc brake linings will be replaced on affected vehicles.
The bonded disc brake linings may separate from the shoes due to a bonding deficiency which may allow corrosion degradation of the bond attachment.
Parking brake cables may be mismatched in length resulting in reduced parking brake application on one wheel and so may not comply with c.M.V.S.S. 105-hydraulic brake systems. Correction: Vehicles will be inspected and those with mismatched cables will have the longer cable replaced with a shorter version.
On vehicles with a 50/50 bench seat, the front outboard passenger seat belt may become difficult to latch and/ or unlatch due to a belt webbing stiffener which could enter the buckle housing and dislodge the buckle latch guide. This could also result in partial latch engagement. Correction: Buckle assembly will be replaced with a revised version if necessary.
Front outboard safety belt may become difficult to latch and or unlatch due to a webbing stiffener entering the buckle housing and dislodging the buckle latch guide.
Mismatched parking brake cable lengths to the rear wheels reduces braking ability of one of the rear wheels, in violation of fmvss 105.
注意:位于安大略省、魁北克省、新不伦瑞克省、新斯科舍省、爱德华王子岛省和纽芬兰省的车辆。由于日间行车灯模块腐蚀失效,这些车辆可能不符合 C.M.V.S.S. 108 号(照明)标准。 更正:日间行车灯模块将更换为带有额外灌封材料的新模块,该材料可覆盖所有原先暴露的元件。
The two air bag system front impact sensors may not be secured to their mounting brackets.
The front disc caliper guide bolts may not have been torqued adequately. This could create the potential for some degree of abnormal brake function. Correction: Front brake caliper guide pin bolts will be tightened to specified torque.
来源:NHTSA(美国,公有领域)、加拿大交通部(加拿大开放政府许可)、DVSA(英国,开放政府许可 v3.0)、RappelConso 与欧盟 Safety Gate(法国,开放许可 2.0)、日本国土交通省(公共数据许可1.0)、韩国国土交通部(car.go.kr)。