Motorrijtuigen - carrosserie (beschermingsmiddelen inzittenden)
Bij de betrokken auto's is kan het stiksel van de gesphouders van de veiligheidsgordels achter mogelijk los komen.
🔔 注册免费账户,接收 Citroën C1 (所有代) 的邮件提醒
Bij de betrokken auto's is kan het stiksel van de gesphouders van de veiligheidsgordels achter mogelijk los komen.
It has been identified that during the fuel tank production process the joint between the tank and the fuel supply pipe assembly may not have been produced to the correct standard. Should this indeed be the case leakage from the supply pipe area of the fuel tank might occur.
La couture des boucles arrière de la ceinture de sécurité pourrait être défectueuse. cela affectera la fonction de protection de la ceinture de sécurité, ce qui augmentera le risque de blessure en cas d’accident.
The stitching of the rear seat-belt buckles could be defective.This will impair the seat belts' protective function, increasing the risk of injury in the event of an accident.
On affected vehicles some rear seat belts may have incorrect stitching on the belt material to connect the buckle to the anchor plate.
Due to an error in the fuel tank production process, the tank may rupture and leak. As a consequence, fuel may spill onto the road and create a hazard for following traffic.
后挡风门玻璃可能粘接不当。
ステアリングコラムシャフトとステアリングギアボックスを接続するボルトの取付けが不適切なため、当該取付部の結合力が不足しているものがある。そのため、かじ取り操作等により当該取付部が分離して、最悪の場合、かじ取り操作ができなくなるおそれがある。
可能会出现车窗玻璃与后车门之间的粘合胶脱落的情况。一旦发生这种情况,玻璃将仅在一个点上固定,并可能掉落到路面上。
车辆受影响时,后车门玻璃与铰链总成之间的粘接可能不符合技术规范。
null Part of the steering column assembly could fail, which could lead to loss of control of the vehicle.
A component of the steering column may not be to specification and could fail. If this occurs there would be a loss of directional control.
null There is a risk of the front shock absorber rods breaking which could lead to loss of control of the vehicle and an accident.
Affected vehicles may have a small defect in the front bumper frame. This may affect its impact absorption in the even of a collision.
The front shock absorber rod may have an internal fault which could cause it to brake. This could have an adverse affect on the front suspension and the driver's ability to control the vehicle.
null Owing to a defective welded joint on the rear-axle cross-member, the weld seam may tear and result in loss of control of the vehicle.
On subject vehicles a weld on the rear cross member might be non-compliant and eventually cause the weld between the cross member and the vehicle body to break. This may lead to a partial detachment of the axle and cause the driver to lose control.
It has been established that the con-rod (big end) shell bearings may not have been manufactured to specification. This could lead to premature deterioration of the shells and if not identified it could result in engine failure.
The left hand side front chassis may have a nonconformity which may lead to a risk of poor securing of the suspension arm.
Due to incorrect machining it is possible that the crankshaft is not to the correct specification which can lead to insufficient lubrication of the crankshaft and subsequent engine failure.
It has been identified that within the mechanism of the accelerator pedal there is a friction lever which interacts with a sliding surface. Over time and under certain conditionsthe contact surfaces may generated excessive friction and latterly the movement of the accelerator pedal. This over time and under certain conditions will result in the accelerator pedal becoming intermittently more difficult to push; or slower to return. In rare instances the accelerator pedal can remain in the partially depressed position.
A possible substandard tapping of one or more of the wheel stud holes may result in a reduction of the wheel stud to hub torque setting.
来源:NHTSA(美国,公有领域)、加拿大交通部(加拿大开放政府许可)、DVSA(英国,开放政府许可 v3.0)、RappelConso 与欧盟 Safety Gate(法国,开放许可 2.0)、日本国土交通省(公共数据许可1.0)、韩国国土交通部(car.go.kr)。