电气系统:点火系统
点火开关可能会出现内部短路。
🔔 注册免费账户,接收 Ford EXP (所有代) 的邮件提醒
点火开关可能会出现内部短路。
点火开关内可能出现短路,进而导致过热、冒烟,并可能在车辆转向柱处引发火灾。该情况可能在车辆行驶过程中或无人看管时发生。纠正措施:更换为改进设计的点火开关。
On 1984 models, external cracks may develop in the engine cylinder heads, which may result in an oil leak onto the exhaust manifold. On 1985 models, the engine rocker cover gasket may split, which could allow oil to leak onto the exhaust manifold. Both these conditions create the possibility of the oil igniting causing an underhood fire. Correction: On 1984 models, the cylinder heads will be inspected and replaced if found to contain external cracks. On 1985 models, the rocker cover gaskets will be inspected and replaced unless they are of a later design.
External cracks above the number 3 cylinder (1984 models) or rocker arm cover gaskets splitting (1985 models) could allow oil to leak onto the exhaust manifold.
Vehicles may have inadequate clearance between the right front brake tubes and a bracket mounted to the engine. Under certain conditions the bracket could contact the metal brake tube and result in abrasion of the tube which could cause a loss of brake fluid and a partial brake loss. This would result in increased stopping distances.
The front sleeve bushings of the cooling fan motors are susceptible to excessive corrosion in areas of high road salt use. This may increase the rotational friction of the fan motor or result in seizure of the armature shaft to the bushing. Either condition may draw current in excess of that of a normally operating motor but less than required to operate the fuse link. This could overheat the motor wiring circuitry and possibly result in an underhood or instrument panel fire. Vehicles affected: Cars not equipped with factory air conditioning. Quebec and atlantic provinces only.
这些车辆可能不符合 c.M.V.S.S. 1103 排放标准。中央燃油喷射器(cfi)在某些工况下可能出现混合气过浓的情况。纠正措施:将安装改进型 cfi 燃油喷油器,并调整怠速转速。
These vehicles do not comply with cmvss 1103 - exhaust emissions. Vehicles affected: 1.6 l engine and atx transmissions
The bolts that attach the d-shaped ring for the shoulder belt are inadequately supported by the material in which they are mounted. The attachment does not comply with the requirements of federal motor vehicle safety standard no. 210, "seat belt assembly anchorages".
The upper torso restraint d-ring which attaches the shoulder belt to the b pillar, under certain test conditions, separated from its anchorage, and may not comply with cmvss 210 - belt anchorage.
These vehicles may not comply with cmvss 1103 - exhaust emissions.
Two door models. Fatigue cracks may occur in the door lock pillars at the front door latch striker reinforcement attachment locations. The fatigue cracks may propogate to the extent that the structural integrity of the door latch striker attachment may be significantly reduced creating the possibility that the door may not be securely retained. This condition is observable by visibly noticeable cracks on the door lock pillar adjacent to the striker assemblies.
Door lock pillars could develop fatigue cracks from normal usage of door, at the point where door latch striker reinforcements are attached.
On the involved vehicles, a thermal limiter in the blower motor resistor circuit of the air conditioner/heater assembly may not function as intended. If the blower motor becomes jammed when the system is operating in the medium-low blower speed, the resistor coils can overheat causing melting and possible ignition.
Vehicles with optional air conditioning. The air conditioner blower motor thermal limiter may not operate as intended when there is a motor blockage or malfunction. Thus, if the blower motor becomes jammed when the system is operating in the medium-low blower speed mode, the resistor coils may overheat causing melting and possible ignition of the polyproplene evaporator housing with associated vehicle damage.
Vehicles equipped with power brakes. Power brake boosters may have bewen improperly assembled by supplier. Mis-indexing of rear shell of some boosters relative to the front shell may have resulted in inadequate crimping of the two shells. If booster were to separate during vehicle operation, complete loss of service brakes would result.
Some vehicles equipped with power brake boosters have front and rear shells that may have been improperly joined. Improperly joined booster shells may separate either partially or completely during brake application.
Vehicle may not meet the fuel spillage requirements of cmvss 301 - fuel system integrity.
Certain vehicles may not meet applicable minimum fuel spillage requirements of federal motor vehicle safety standard no. 301, "fuel system integrity". During a 30 mph rear impact test, fuel spillage limits were exceeded by vehicle.
来源:NHTSA(美国,公有领域)、加拿大交通部(加拿大开放政府许可)、DVSA(英国,开放政府许可 v3.0)、RappelConso 与欧盟 Safety Gate(法国,开放许可 2.0)、日本国土交通省(公共数据许可1.0)、韩国国土交通部(car.go.kr)。