Certain sport utility vehicles that have been exposed to fuel contaminated with silicon may develop small pin holes in the fuel pump feed port. Silicon has been identified in the fuel systems of affected vehicles and in certain fuel available in the region of tyler, texas. This recall will be launched for vehicles registered in texas and the four surrounding states: Oklahoma, arkansas, new mexico and louisiana.
On certain sport utility vehicles, the passenger-side air bag inflator modules were manufactured and shipped without a necessary component known as a check valve pin.
Vehicle description: Certain sport utility vehicles were built with the inflators in the passenger side air bag modules having the wrong amount of generant.
Vehicle description: Sport utility vehicles. During the manufacture of certain fuel return hoses, incorrect rubber material for the outer layer was used.
Vehicles may exhibit a condition in which there is the possibility of partial engagement of the latch plate into the type-521 model seat belt buckle (false latch). This could result in failure of the seat belt system to provide proper occupant restraint in the event of a crash or sudden stop. Correction: Belt buckles will be inspected for the affected lot numbers and replaced if necessary.
THE (Takata) ABS PLASTIC FRONT SEAT BELT RELEASE BUTTONS ON THESE VEHICLES MAY BREAK ALLOWING PLASTIC PIECES TO FALL INTO THE BUCKLE ASSEMBLY. IF THIS SHOULD HAPPEN, A NO LATCH, FALSE LATCH OR FAILURE TO UNLATCH CONDITION COULD OCCUR CREATING THE RISK OF PERSONAL INJURY IN THE EVENT OF A CRASH OR SUDDEN STOP. CORRECTION: FRONT SEAT BELT BUCKLES WILL BE REPAIRED OR REPLACED AS NECESSARY.
Vehicles with 3.2 litre engines may experience dislodging of the camshaft end plug(s) from the cylinder heads causing rapid oil loss. Oil spilling on the exhaust system could result in an engine compartment fire. Correction: A camshaft end plug retaining plate kit will be installed on affected vehicles.
Constant expansion and contraction of the cylinder head causes the camshaft seal end plug can become dislodged from the cylinder head. This allows oil to leak from the camshaft.
The transmission fluid level gauges (dip sticks) installed in these vehicles are not to designed specifications. The gauge indicates that transmission fluid should be added when it is at the correct level.
On vehicles with automatic transmission and v6 engine, overfilling of transmission oil in conjunction with high oil temperature, could cause oil to flood through the air bleed groove in the oil level gauge plug. Leaking oil could wet the exhaust manifold and result in an engine compartment fire. Correction: Dealers will install a new automatic transmission dipstick with an improved plug design and clearer oil level marks.
Certain vehicles fail to conform to CMVSS 135 "Passenger Car Brake System". The brake warning lamp may not illuminate in the event of decreased brake fluid level. Correction: Dealer will replace the current brake fluid warning circuit diode with a newly designed diode.
On certain sport utility vehicles and pickup trucks, the latch plate used in the seat belt buckle was not manufactured according to design dimensions. If the seat belt tongue is inserted slowly at an angle into the buckle, there is a possibility of partial engagement.
On certain vehicles, a fuel return hose may not contain the desired ozone protection which could result in the hose having a reduced life expectancy. Over time, the hose may deteriorate and leak fuel. Correction: Dealers will inspect the fuel return hose date code and replace the hose if required.
Vehicle description: Sport utility vehicles. These vehicles fail to comply with the performance requirements of fmvss no. 201, "occupant protection in interior impact."
Certain V6 Rodeo do not comply with the requirements of CMVSS 1105 - Evaporative Emissions. The rubber purge hose of the Enhanced Evaporative Emission Control System (EVAP) may crack, due to proximity of the exhaust pipe. Correction: Dealers will install an EVAP pipe and hose assembly using a clearance template, and will inspect routing clearances after installation.
On certain vehicles, the engine wire harness ground connection terminal may fracture due to improper crimping. In a case where the terminal is fractured, the powertrain control module (PCM) may misinterpret the damage as a signal indicating a high vehicle speed. The PCM will then cut the fuel causing a "no-start" condition or an engine stall. Correction: Wire harness will be replaced with a new harness.
Vehicle description: Sport utility vehicles. A ground connection terminal was not properly crimped in the supplier's engine wiring harness manufacturing line. This improper crimping process can leave an impression on the terminal that will eventually cause a stress fracture. S
Vehicle description: Multi-purpose passenger vehicles equipped with a driver's side optional equipment rubber floor mat. Repeated movement of the driver's feet and actuation of the accelerator pedal can result in a shifting of the mat's position. This shifting can cause an interference with the accelerator pedal.
The voltage regulator may contain manufacturing errors in an integrated circuit. This may cause excessive electrical charging of the alternator (overcharge), resulting in engine control malfunction, and/or in the worst case, eventual engine stall. The possible cause of this condition is a faulty ic regulator in the alternator. Correction: Ic regulator will be replaced with a new ic regulator. When repairs are completed, a performance check will be done to verify proper functioning of the charging indicator light and proper battery voltage output.