免费阅读 · 免费账户即可贡献Anticars(2000)的继任者

Mercedes-BenzMercedes-Benz E级

1985– · 8 各代车型 · 已记录92项缺陷 · 7个市场
各代车型

Mercedes-Benz E级 所有代的全部信息:缺陷、召回、技术通报和讨论。选择某一代以缩小范围。

最严重的缺陷

查看全部 (92) →
m

Electrical system: problems reported by owners

244 owners in the United States reported problems with the electrical system of this car to NHTSA (model years 1994–2001), typically at around 112,000 miles. Most often named: wiring:front underhood (24%), wiring (16%). Reported consequences: 3 crashes, 24 fires, 9 injuries.

✓ Mecafile 对官方数据的分析1994–2001以原文(英语)显示 · 翻译待完成查看详情 →
m
严重发动机NAE级 W210 · 1994–2003

Engine and cooling: problems reported by owners

91 owners in the United States reported problems with the engine and cooling of this car to NHTSA (model years 1994–2001), typically at around 77,000 miles. Most often named: engine (25%), engine:gasoline (16%). Reported consequences: 6 crashes, 5 fires, 11 injuries.

✓ Mecafile 对官方数据的分析1994–2001以原文(英语)显示 · 翻译待完成查看详情 →
m

Airbags: problems reported by owners

76 owners in the United States reported problems with the airbags of this car to NHTSA (model years 1995–2001), typically at around 120,000 miles. Most often named: frontal (26%). Reported consequences: 24 crashes, 4 fires, 29 injuries.

✓ Mecafile 对官方数据的分析1995–2001以原文(英语)显示 · 翻译待完成查看详情 →

最新官方召回

查看全部 (713) →
E级 V213 · 2016–2023
召回中等变速箱KR

동력전달장치 기타

공급업체의 생산 공정의 편차로 인해 시간이 지남에 따라 드라이브 샤프트의 유니버셜 조인트가 마모될 수 있으며, 이로 인해 유니버셜 조인트에서 윤활유 손실이 발생하여 유니버셜 조인트가 파손될 수 있음. 그 결과로 트랜스퍼 케이스와 전륜 구동 장치 간의 연결이 끊어져 추진력을 잃을 수 있고 충돌 위험이 증가할 수 있음이 확인됨에 따른 리콜 <대상차량별 생산일자> S 450 4MATIC: 2018.01.25~2019.11.14 S 560 4MATIC: 2019.08.30~2019.09.12 CLS 400 d 4MATIC: 2019.02.25~2019.04.11 S 350 d 4MATIC: 2019.04.09 E 450 4MATIC: 2019.02.05 S 400 d 4MATIC: 2017.12.11

国土交通部 · 韩国2026年9月30日6389车型年份 2017–2019以原文(韩语)显示 · 翻译待完成查看详情 →
E级 V213 · 2016–2023
召回中等变速箱UK

SRPC2603 - Drive Shaft Joint

Mercedes-Benz AG has determined that on certain 4MATIC E-Class (213 platform) S-Class Coupé (217 platform) S-Class (222 platform) E-Class Coupe/Convertible (238 platform) GLC (253 platform) and CLS (257 platform) vehicles increased wear of the universal joint on the drive shaft might occur.

DVSA · 英国2026年9月21日R/2026/148车型年份 2019以原文(英语)显示 · 翻译待完成查看详情 →
E级 W212 · 2008–2016E级 V213 · 2016–2023
召回严重悬架EU

Motorrijtuigen en aanhangwagens - stuurinrichting

De drie aluminium schroeven waarmee de power-pack aan de stuurinrichting is bevestigd, kunnen door blootstelling aan water en strooizout roesten.

rdw2026年8月28日MGP230033车型年份 2010–2016以原文(荷兰语)显示 · 翻译待完成查看详情 →

最新技术服务通报

查看全部 (874) →
E级 W214 · 2023–
通报轻微车身NA

通报

Complaint Wheezing noises/squeaking noises from the front shock absorbers when passing over surface undulations and rough road. Noise MUST match those heard in the attached videos. Cause Wheezing noises: Flow noises of the damper oil Squeaking noises: From the mechanical rubber valve in the dividing piston Remedy In case of complaints, the front shock absorbers must be replaced. If shocks have been replaced and noise persists, please open a TIPS case to the Body, Chassis, Entertainment inbox.

NHTSA · 制造商通报11039086车型年份 2024–2027以原文(英语)显示 · 翻译待完成查看详情 →
E级 W214 · 2023–
通报中等悬架NA

通报

Complaint Cracking noises on load change from rear axle (can be heard from wheel side). See attached reference video Cause Micromovement between the rear halfshaft (axle shaft) and wheel bearing mounting surface. Remedy To verify, a test drive and thorough NVH diagnosis must be performed in order to verify the root cause of the noise. If the axle shafts have been identified as the source of the noise, perform the following steps: 1. Verify that rear axle side shaft part number A 214 350 44 06 are currently installed on both sides. If an earlier part number is installed, replace the affected side shaft(s) with A 214 350 44 06. (Before installation, proceed with remaining steps) 2. Clean the contact surfaces of the side shafts and wheel bearings (remove any existing Molykote coating and wear debris). 3. Install one antiknock washer per side (A000 990 86 62) 4. Reinstall both side shafts 5. Perform road test and verify noise is no longer present Note: Application of Molykote coating is no longer required.

NHTSA · 制造商通报11038946车型年份 2025–2027以原文(英语)显示 · 翻译待完成查看详情 →
E级 V213 · 2016–2023E级 W214 · 2023–
通报中等悬架NA

通报

Complaint Diverse functional limitations in the vehicle in combination with various warning and fault messages in the instrument cluster display. Cause Communication timeouts mean that communication errors may occur in the onboard electrical system, which can result in various fault messages being displayed in the instrument cluster. This could be down to delayed feedback from the drivetrain control unit (N127) (CPC) to other control units networked to the CAN bus. Information: Only valid for vehicles through production period 10/2025. Not valid for vehicles with control unit CDCC (N125, central controller charging and driving) It may not be possible to attribute any communication errors stored in the control units on the CAN bus to a specific cause In rare instances, there may be a brief activation of the yellow warning lamp for engine diagnosis or there may be a sporadic delay with the start enable. There may not be any specific fault codes present that indicate a specific component. Example image: Fault messages in instrument cluster: The reason for this could be down to delayed feedback from the control unit CPC3 to other control units networked on the CAN bus. Remedy Do not replace any components!!! ******************************************************************************************************* 1. Connect charger (see AR54.10P1127WT). Note: An adequate voltage from the onboard electrical system battery must be guaranteed for the entire duration of the work procedure. Otherwise, the control units could be damaged if an undervoltage occurs. Information: Observe the operating instructions of the charger. Information: Use the charger to ensure an adequate voltage (at least 12.5 V) from the onboard electrical system battery. 2. Connect diagnostic system (see AD00.00P200006FR). Note: Always use the latest XENTRY Diagnostics software release. Information: Strict compliance with the operation steps in XENTRY Diagnostics is absolutely essential. 3. Select control unit N127 (CPC) via the direct link using XENTRY Diagnosis. Information: To do so, select the following menu items: Control units view Drive systems N127 "Drivetrain" control unit (CPC) 4. Update software for control unit N127 (CPC) (see AR54.21P001401Y). Info: To do so, select the following menu items: Adaptations Control unit update Update control unit software. Information: You are then automatically guided through the steps "Update of control unit software" and "SCN coding". Always observe the following operation steps at all times 5. Disconnect diagnostic device from vehicle (see AD00.00P200006FR). 6. Disconnect charger from vehicle (see AR54.10P1127WT).

NHTSA · 制造商通报11038925车型年份 2023–2026以原文(英语)显示 · 翻译待完成查看详情 →

最新论坛话题

暂无讨论。

缺陷和讨论按代归档:请先在上方选择一代再发布。

来源:NHTSA(美国,公有领域)、加拿大交通部(加拿大开放政府许可)、DVSA(英国,开放政府许可 v3.0)、RappelConso 与欧盟 Safety Gate(法国,开放许可 2.0)、日本国土交通省(公共数据许可1.0)、韩国国土交通部(car.go.kr)。