نشرة
Intelligent Battery Sensor-IBS Installation, Battery Charging Message, Start Stop Charging Warning Lamp Illuminated On Stop Start Equipped Vehicles
🔔 أنشئ حسابًا مجانيًا لتلقي تنبيهات البريد عن Fiat 500 (كل الأجيال)
النشرات الفنية (TSB) تعليمات إصلاح يرسلها المصنعون إلى وكلائهم بشأن مشكلات معروفة. ليست استدعاءات سلامة، لكنها كثيرًا ما تؤكد وجود عطل.
Intelligent Battery Sensor-IBS Installation, Battery Charging Message, Start Stop Charging Warning Lamp Illuminated On Stop Start Equipped Vehicles
Fiat: Due to tee being installed backwards, the boost vacuum purge harness causes a mil illumination with p1cea and if necessary be replaced. *pe
Flash: Drivetrain Control Module (DTCM) Diagnostic and System Improvements This bulletin involves reprogramming the DTCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs):C2502-64 - Signal Plausibility Failure. C2210-92 - ETM Hall Sensor Performance Or Incorrect Operation. C2220-54 - ETM Calibration Error Missing Calibration. C2020-01 - ECU Internal Fault - General Electrical Failure. This software update also includes the following enhancementsReduce Rear Drive Module (RDM) noise during disconnect phase at speeds above 45 kph (28 mph)North America Only.
The customer may describe the upper switch pod buttons (electronic stability control, hazard, and rear defrost) on the center instrument panel bezel are sticking.
Flash: Drivetrain Control Module (DTCM) Diagnostic and System Improvements This bulletin involves reprogramming the DTCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs):C2502-64 - Signal Plausibility Failure. C2210-92 - ETM Hall Sensor Performance Or Incorrect Operation. C2220-54 - ETM Calibration Error Missing Calibration. C2020-01 - ECU Internal Fault - General Electrical Failure. This software update also includes the following enhancementsReduce Rear Drive Module (RDM) noise during disconnect phase at speeds above 45 kph (28 mph)North America Only.
2.4L Ignition Coil Boot Replacement This bulletin involves replacing all four ignition coil insulating boots. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set:P0300 - Multiple Cylinder Misfire P0301 - Cylinder 1 Misfire. P0302 - Cylinder 2 Misfire. P0303 - Cylinder 3 Misfire. P0304 - Cylinder 4 Misfire. Some customers may also experience the following condition:Rough running engine.
2.4L Ignition Coil Boot Replacement This bulletin involves replacing all four ignition coil insulating boots. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find thatone or more of the following Diagnostic Trouble Codes (DTCs) have been set:P0300 - Multiple Cylinder Misfire P0301 - Cylinder 1 Misfire. P0302 - Cylinder 2 Misfire. P0303 - Cylinder 3 Misfire. P0304 - Cylinder 4 Misfire. Some customers may also experience the following condition:Rough running engine.
2.4L Ignition Coil Boot Replacement This bulletin involves replacing all four ignition coil insulating boots. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find thatone or more of the following Diagnostic Trouble Codes (DTCs) have been set:P0300 - Multiple Cylinder Misfire P0301 - Cylinder 1 Misfire. P0302 - Cylinder 2 Misfire. P0303 - Cylinder 3 Misfire. P0304 - Cylinder 4 Misfire. Some customers may also experience the following condition:Rough running engine.
MIL Illumination, P0141 Oxygen Sensor 1/2 Heater Performance
Flash: Instrument Panel Cluster (IPC) Enhancement This bulletin involves reprogramming the Instrument Panel Cluster (IPC) with thelatest available software. Customers may experience the following condition listed below:When changing the language selection to Korean in the radio, the radioreverts back to English after the key is removed from the ignition.
Navigation Map Activation RA3 Radio This bulletin involves activating the navigation system on the RA3 radio prior to sale of the vehicle.
Incorrect Value for Distance To Service This bulletin involves the replacement of the Instrument Panel Cluster (IPC). The customer may notice when looking at the Kilometers ?(km) to service? that the value is set to 30,000 km. In LATAM it should be set at 15,000 km.
Incorrect Value for Distance To Service This bulletin involves the replacement of the Instrument Panel Cluster (IPC). The customer may notice when looking at the Kilometers ?(km) to service? that the value is set to 30,000 km. In LATAM it should be set at 15,000 km.
Flash: Clock In The Cluster Gains Or Loses Time This bulletin involves updating the software in the Instrument Panel Cluster (IPC). Some customers may notice that their clock may gain or loses time.
RA3 RA4 Radio Enhancements This bulletin involves inspecting and, if required, updating the radio software. A small number of customers may experience one or more of the following: Navigation failed message is displayed. Clock not automatically updating to local time. Poor or no connection to cellular network. HVAC temperature out of sync with radio display (KL vehicles). Display goes blank/black. Radio locks up. Some Uconnect App remote commands do not execute with the vehicle.
Keyfob 2016 Vehicle Keyfobs with Passive Entry Keyless Go Feature - Engineering is investigating a keyfob unable to program or no function or low keyfob coin battery condition.~ Prior to replacing keyfob on MY16 vehicles, please contact Raja Charabuddi on cell (248) 202-7313. If no response within 15 minutes, proceed with repair.
Flash: Clock In The Cluster Gains Or Loses Time This bulletin involves updating the software in the Instrument Panel Cluster (IPC). Some customers may notice that their clock may gain or loses time.
Radio Pre-Authorization Program - Select 7.0/8.4/8.4N Radios (New and Exchange) - 2018 Model Year Vehicles
Loss Of Communications With Convergence Telematics Module (CTM) This Bulletin involves replacement of the Convergence Telematics Module (CTM). Customer may experience no response from voice recognition or Bluetooth features. On further inspection the technician may find U1733-87 Lost communication with the CTM.The condition is caused by the CTM not communicating.
Tom Tom Message Searching For GPS Or Can't Pair With Blue And Me This bulletin involves updating the software or replacing the unit if instructed. The customer may experience one the following conditions: The device packaging is correct and the splash screen shows the Blue and Me Tom Tom logo, but the device doesn't include the ?Find Blue and Me? icon on the main menu. The device can be used as a normal Tom Tom, but the extra functions including pairing with the Blue and Me module are not available. The device will only display a message "Searching for GPS". Due to a software error on the internal clock, the Tom Tom device did not detect the 2012 Leap Year / Leap day of February 29. As a result, the device could no longer detect GPS satellite signals after April 1, 2012. Depending on the condition, either updating the software or replacing the unit will repair the condition.
Navigation Map Activation RA3 Radio This bulletin involves activating the navigation system on the RA3 radio prior to sale of the vehicle.
Cluster Average Energy Trip Reset This bulletin involves updating the Instrument Cluster (IC) software. The customer may describe the trip average energy resets at approximately 2,600 miles (4,184 km).
Air Conditioning Inoperative This bulletin involves replacing the Manual Climate Control Module. A small number of customers may experience the loss of air conditioning operation (AC will not turn on).
Matte Finish Care And Protection Matte paint is a unique exterior treatment that gives your Fiat 500X a distinctive appearance. Matte finishes are different from other automotive paints and need special care to maintain their appearance. Typical gloss paints use a high gloss clear-coat finish that reflects light and gives a shiny appearance. A matte finish uses a different coating that diffuses light, providing a unique ?flat? finish. Unlike a typical high gloss clear-coat, damage to the matte coating (such as scratches or wear from aggressive cleaning) cannot be polished or buffed out. Once an area is damaged or becomes shiny, the ?flat? appearance cannot be restored.
Air Conditioning Inoperative This bulletin involves reprogramming the Heating Ventilation Air Conditioning (HVAC) module with the latest available software. A small number of customers may experience the loss of air conditioning operation.
المصادر: NHTSA (الولايات المتحدة، ملك عام)، وزارة النقل الكندية (رخصة الحكومة المفتوحة – كندا)، DVSA (المملكة المتحدة، رخصة الحكومة المفتوحة 3.0)، RappelConso وSafety Gate الأوروبي (فرنسا، الرخصة المفتوحة 2.0)، ووزارة MLIT اليابانية (رخصة البيانات العامة 1.0)، ووزارة MOLIT الكورية (car.go.kr).