2017 vehicles equipped with a 2.0L GTDI, 2.3L GTDI, or 2.5L PFI engine will either be equipped with a diamond washer on each side of a smooth-faced crankshaft timing sprocket (early build), or a crankshaft timing sprocket with laser etched faces and no diamond washers (late build). If equipped, diamond washers should be cleaned, inspected and reused, if undamaged. Diamond washers should never be installed along with a laser etched crankshaft timing sprocket. Related WSM procedure information is in the process of being updated.
NHTSA · نشرة المصنع10119671سنوات الطراز 2017معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Some 2016-2017 Ford/Lincoln vehicles SYNC 3 may exhibit an intermittent blank screen. Check for SYNC software update under the OASIS Tab SYNC selection. If update is available refer to WSM, Section 415-00 and update APIM software. During the update process the SYNC status bar shows Updating System Software for approximately 30 minutes. After Installation Complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or blank screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
NHTSA · نشرة المصنع10115952سنوات الطراز 2017معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Some 2016 c-max and focus electric vehicles may exhibit a false activation of the alarm system. A work around until the software is updated(4th qtr. 2016), procedure is available. 1. Put the vehicle in park. 2. Take your foot off the brake pedal and keep it off. 3. Turn the vehicle off (push button start/stop. 4.Exit vehicle and lock the doors to activate the alarm. Note: If the brake is touched after turning the key off then just turn the car on again and start this procedure again.
NHTSA · نشرة المصنع10095978سنوات الطراز 2016معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Some 2016 c-max and focus electric vehicles may exhibit a false activation of the alarm system. A work around until the software is updated(4th qtr. 2016), procedure is available. 1. Put the vehicle in park. 2. Take your foot off the brake pedal and keep it off. 3. Turn the vehicle off (push button start/stop. 4.Exit vehicle and lock the doors to activate the alarm. Note: If the brake is touched after turning the key off then just turn the car on again and start this procedure again.
NHTSA · نشرة المصنع10092572سنوات الطراز 2016معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Ford/lincoln: Due to an adherence failure of rtv sealant, there is a transmission fluid leakage, in some vehicles, from damper housing to transmission case joint. Model 2013 c-max, 2013-14 fusion, mkz. *pe
NHTSA · نشرة المصنع10056421سنوات الطراز 2013معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Ford/lincoln: The damper housing to transmission case joint, there is a fluid leak caused by an adherence rtv failure. 2013 c-max, 2013-2014 fusion, mkz. *pe
NHTSA · نشرة المصنع10056375سنوات الطراز 2013معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Ford: Within 20 seconds after remote starting vehicle, there is a start stall issue and diagnostic trouble code (dtc) p1594 is set in body control module (bcm). Model 2012-2014 focus, 2013-2014 escape, c-max. *pe
NHTSA · نشرة المصنع10055019سنوات الطراز 2014معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Ford/lincoln: There is a no start condition and the red triangle lamp will illuminate and the battery energy control module (becm) will need reprogramming to latest calibration due to storage of diagnostic trouble codes (dtc) p0adc, p0ae0 and/or p0ae7. Model 2013 c-max, 2013-2014 fusion, mkz. *pe
NHTSA · نشرة المصنع10054767سنوات الطراز 2014معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
قد تعاني بعض المركبات المختلفة من طرازات 2012-2015 والمزودة بمودم 3G من ضعف في أداء المودم. وقد يرجع ذلك إلى إيقاف خدمة الاتصال الخلوي 3G بدءًا من أغسطس 2021 وحتى مارس 2022. ومع إيقاف خدمة 3G الخلوية، ستفقد المركبات المزودة بوحدة التحكم في القياس عن بُعد (TCU) 3G وظيفة الاتصال/التطبيق في تطبيق MyFord Mobile وتطبيق MyLincoln Mobile. ولا ينبغي بعد الآن إجراء إصلاح أو استبدال وحدة TCU باستخدام مخزون قطع الخدمة الحالي. وسيؤدي استبدال وحدة TCU 3G لهذه المشكلة إلى مشكلات في البرمجة، لذا لا ينبغي إجراء الإصلاحات.
## ملخص
قد تُظهر بعض مركبات Ford و Lincoln للموديلات 2018-2020 المزودة بوحدة التحكم في الإرسال (TCU) ونقطة اتصال Wi-Fi، رسالة "ميزة نقطة اتصال المركبة غير مفعّلة على هذه المركبة" عند محاولة الدخول إلى قائمة نقطة الاتصال. وعند استخدام تطبيق FordPass/Lincoln Way، قد يتلقى العميل رسالة تفيد بأن Wi-Fi معطّل في هذه المركبة.
تحقق من مواصفات المركبة أو معلومات بناء المركبة للحصول على رمز mfal في موقع PTS (Detailed Vehicle Specifications). إذا كان mfal = WAFAC أو WAFAB، فلا تستبدل وحدة TCU، إذ إن الهندسة تحقق حاليًا في هذه الحالة.
أبلغ العملاء بأن Ford تعمل على تطوير تحديث برمجي من المتوقع إصداره في أوائل مارس. وفي الوقت الحالي، أخبر العميل بأنه يمكنه مواصلة قيادة المركبة، وحدد معه موعد متابعة في أوائل مارس. راقب OASIS للاطلاع على التحديثات.
Some 2018-2020 Ford and Lincoln vehicles equipped with TCU and WiFi Hotspot, May display Vehicle Hotspot feature not enabled on this vehicle when attempting to enter the Hotspot menu. When using the FordPass/Lincoln Way application, the customer may receive a message saying Wi-Fi has been disabled from this vehicle. Check the vehicle specifications or vehicle build information for the mfal code. If mfal = WAFAC or WAFAB do not replace the TCU, engineering is currently investigating this condition. Inform customers Ford is developing a software fix that is expected in early January. In the interim, let the customer know they can continue to drive the vehicle and schedule a follow-up appointment with the customer for early January. Once the update becomes available, contact the customer and confirm the service appointment is going forward. Monitor OASIS for updates.
NHTSA · نشرة المصنع10181913سنوات الطراز 2018معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
بعض مركبات Fusion Hybrid وFusion Energi وMKZ Hybrid وC-Max لعام 2017، وFusion Hybrid وMKZ Hybrid لعام 2019، التي صُنعت في أو قبل 27-Jan-2019، قد تظهر فيها مصباح مؤشر الأعطال (MIL) مضاءً مع رمز عطل التشخيص (DTC) P013A مخزّنًا في وحدة التحكم في نظام الدفع (PCM). وقد يكون السبب معلمات مستشعر الأكسجين اللاحق في برمجية PCM. ولحل هذه الحالة، قم بتحديث برمجية PCM.
Some 2014-2015 Escape, 2015 C-Max and Focus vehicles equipped with integrated remote start may exhibit an illuminated MIL with diagnostic trouble code (DTC) P0116 in the powertrain control module (PCM) immediately following a remote start event. Vehicles may also display a warning message stating Engine Coolant Over Temperature. This condition may occur when remote start is used and the vehicle is allowed to time out (engine shuts off). Reprogram the body control module (BCM) using the latest software version of the appropriate Ford diagnostic scan tool. For claiming, use causal part 12A648 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA · نشرة المصنع10153947سنوات الطراز 2015معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Some 2016 C-MAX and Focus Electric vehicles built on or after 11-May-2016 may exhibit a false activation of the alarm system. Reprogram the body control module (BCM) to the latest level using Integrated Diagnostic System (IDS) release 110.03 or higher. To correct the concern Make sure you are connected to the internet when entering module programming to obtain the latest updates. Use the applicable labor operation in section 10 of the Service Labor Time Standards manual and causal part 14A068 when claiming repair. Calibration files may also be obtained at www.motorcraftservice.com
NHTSA · نشرة المصنع10144214سنوات الطراز 2016معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
The EV Range after fully charging a Focus Electric, C-MAX/Fusion Energi may vary after each charge event. The window sticker indicates 0-20 mile range for C-MAX Energi, 0-21 mile range for Fusion Energi. Variation of EV range may not indicate a battery or charging concern. EV range is similar to the DTE display on gasoline vehicles, EV range will vary with driving/operating conditions. Conditions include: extreme outside temperatures, terrain, driving style, city or highway driving, tire pressure, and use of accessories. If the customer replaces the low roll resistance tires with a more aggressive tread the range will suffer. Using the cabin heater and A/C, which are electric, will also decrease EV range. To temporarily remove the impact of driving/climate history , reset the Driving History/Lifetime Summary by using the Settings menu on the left side of the instrument cluster, under Display
NHTSA · نشرة المصنع10140321سنوات الطراز 2017معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
The EV Range after fully charging a Focus Electric, C-MAX/Fusion Energi may vary after each charge event. The window sticker indicates 0-20 mile range for C-MAX Energi, 0-21 mile range for Fusion Energi. Variation of EV range may not indicate a battery or charging concern. EV range is similar to the DTE display on gasoline vehicles, EV range will vary with driving/operating conditions. Conditions include: extreme outside temperatures, terrain, driving style, city or highway driving, tire pressure, and use of accessories. If the customer replaces the low roll resistance tires with a more aggressive tread the range will suffer. Using the cabin heater and A/C, which are electric, will also decrease EV range. To temporarily remove the impact of driving/climate history , reset the Driving History/Lifetime Summary by using the Settings menu on the left side of the instrument cluster, under Display
NHTSA · نشرة المصنع10138522سنوات الطراز 2017معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Some 2016 Escape and Focus vehicles equipped with a front control display interface module (FCDIM) may exhibit the inability to store AM/FM presets and/or preset buttons work erratically. Engineering is currently investigating this concern. Until a new service procedure and/or parts are available use the pre-set buttons in the following manner. To store/program a new station for a pre-set location, press and hold desired button for 3 seconds. To select a previously programmed pre-set location, perform a quick press and release of the button. Refer to Workshop Manual (WSM) Section, 415-00 for normal diagnostics. Continue to monitor OASIS for updates.
NHTSA · نشرة المصنع10125089سنوات الطراز 2016معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Some 2017 C-MAX vehicles built 1-Jun-2017 and through 26-Sep-2017 may exhibit an illuminated MIL with DTCs P26D0, P26CA, P059F, U019F, U0194, U091F and/or U0284. This may be due to water in the jumper harness connector C1651 and the attached connector on the active grill shutter actuator. Remove connector, clean and dry, add electrical grease Motorcraft XG-12 or equivalent to the terminals. Engineering is investigating, monitor OASIS for updates.
NHTSA · نشرة المصنع10125076سنوات الطراز 2017معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Some 2017 Ford and Lincoln vehicles equipped with SYNC 3 and navigation may exhibit a condition in which the SiriusXM Traffic Listing is not loading but all remaining Travel Link features operate properly. SiriusXM Traffic is only available on vehicles equipped with navigation, only in select markets and requires an active subscription to SiriusXM Traffic information. If SiriusXM Traffic will not load attempt the following procedure. Turn the ignition off, open and close the drivers door, wait for 3 minutes, then drive the vehicle outside to obtain a clear view of the sky. SiriusXM Traffic should recover. If SiriusXM Traffic does not recover continue to monitor OASIS for future updates. Engineering is aware of this concern and no component replacement or any software re-flashes should be performed at this time. The SYNC version can be confirmed via OASIS.
NHTSA · نشرة المصنع10109058سنوات الطراز 2017معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Some 2016-2017 Ford and Lincoln vehicles equipped with SYNC 3 may have DTCs U3000:04, B108E:12 and/or U1A00:87 present in the APIM. If these DTCs are present and no other symptoms are reported by the customer, then clear the DTCs and retest. If the DTC(s) do not return then no further repairs should be attempted. If one or more DTCs return as current faults and/or the customer reports other symptoms, then refer to Workshop Manual, Section 415-00 for further diagnostics. The SYNC version can be confirmed via OASIS.
NHTSA · نشرة المصنع10109054سنوات الطراز 2016معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Some 2017 C-MAX/Fusion Hybrid/Energi and MKZ Hybrid vehicles may exhibit an illuminated MIL with DTC P0071 stored in the powertrain control module (PCM). This DTC can be set after the vehicle is stored inside a warm location for several hours and then driven on a cold day. Under these conditions the PCM may see a temperature sensor concern when it first compares the ambient air temperature (AAT) sensor to other engine temperature sensors and set the DTC. Reprogram the PCM to the latest calibration using Integrated Diagnostic System (IDS) release 104.04 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. Calibration files may also be obtained at www.motorcraftservice.com.
NHTSA · نشرة المصنع10109002سنوات الطراز 2017معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Some 2012-13 Focus and 2013 Escape/C-MAX vehicles may have the wrong part in the box for the BCM (base 14A068). The suspect service part number is GV6Z-14A068-G. The wrong part will have an engineering number of GV6T-14A073-GD and it will not work. The correct part will have engineering part number of GV6T-14A073-with a suffix of XA, XB, XC, or XF. Dealers should utilize the normal return process of a miss packaged part. Continue to monitor OASIS. When this concern is resolved, an update will be provided.
NHTSA · نشرة المصنع10109025سنوات الطراز 2013معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Some vehicles may exhibit an illuminated mil with diagnostic trouble codes (dtcs) p0011, p0012, p0014, p0015, p0016, p0017, p0018, p0019, p0021, p0022, p0024 and/or p0025. This may be due to small debris causing the vct solenoid to stick. Before attempting any component diagnosis or replacement of the vct solenoid, refer to powertrain control and emissions diagnosis (pc/ed) pinpoint test hk11 to cycle the affected vct solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6m280 and applicable labor operations in section 10 of the service labor time standards (slts) manual.
NHTSA · نشرة المصنع10099458سنوات الطراز 2017معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
المصادر: NHTSA (الولايات المتحدة، ملك عام)، وزارة النقل الكندية (رخصة الحكومة المفتوحة – كندا)، DVSA (المملكة المتحدة، رخصة الحكومة المفتوحة 3.0)، RappelConso وSafety Gate الأوروبي (فرنسا، الرخصة المفتوحة 2.0)، ووزارة MLIT اليابانية (رخصة البيانات العامة 1.0)، ووزارة MOLIT الكورية (car.go.kr).