Some customers may experience a SBS/SCBS, LAS/LDWS and/or HBC warning light on. A system error message may also be found in the center display. DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction). DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction) is stored in the FSC module and cannot be erased. This concern may be caused by a hardware failure of an internal device of the FSC, which results in a malfunction detection. To eliminate this concern, the production process of the FSC has been modified.
NHTSA · نشرة المصنع10199641سنوات الطراز 2021معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
If you experience issues with the current version of ID's such as missing tools or modules not showing after completing a network test, be advised that we are aware of these issues and are working to resolve them. As a counter measure, it is advised that you un-install ids and re-install version 103.00 and "do not update" until further notice.
NHTSA · نشرة المصنع10185813سنوات الطراز 2017معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
قد يشتكي بعض العملاء من أي مما يلي:
1. لا تعرض شاشة مركز الترفيه في السيارة رمز التفويض (OTP) أثناء تسجيل المركبة المتصلة بتطبيق MyMazda.
2. تعطل وظيفة (وظائف) التحكم عن بُعد.
قد تظهر على بعض المركبات إضاءة مؤشر عطل المحرك (Check Engine) مع تخزين رمز العطل DTC P0300:00 (تم اكتشاف إخفاق عشوائي). قد يكون السبب سوء اكتشاف حالة إخفاق بسبب خلل في منطق التحكم في وحدة التحكم بالمحرك (PCM). وللقضاء على هذه المشكلة، تم تعديل منطق التحكم في وحدة PCM.
قد يلاحظ بعض العملاء أن مصباح الشحن يضيء أثناء القيادة. وعند الفحص، يتم تخزين رمز العطل DTC P2502:00 PCM (عطل في الجهد المتولد من المولد) في الذاكرة. وقد يكون السبب وجود مقاومة بين لوحة الدوائر والأرضي. عندما يمر تيار كهربائي عالي الشدة، قد لا يكون موضع طرف الأرضي كافيًا. وللقضاء على هذه المشكلة، تم تعديل برنامج التحكم في محول DC-DC. كما تمت مراجعة إجراء التصنيع. وتمت زيادة عزم شد طرف الأرضي ولوحة الدوائر.
Some customers may experience a check engine light illumination at idle while stopped with DTC P0300:00 stored, resulting in rough idle conditions. P0300:00: Random misfire detected This concern is caused by improper engine control in the idle range. To eliminate the concern, the PCM control software has been modified.
NHTSA · نشرة المصنع11008417سنوات الطراز 2021معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Some customers may experience the CHECK ENGINE light ON with DTC P0089:00 (Spill valve control solenoid valve control circuit range/performance problem) stored. This is caused by improper control software of the PCM detecting a false error, even with normal fuel pressure operation. To correct this issue, the control software of the PCM has been modified.
NHTSA · نشرة المصنع10190951سنوات الطراز 2021معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Some vehicles may experience the check engine light on with DTCs P2096:00, P2097:00 and/or P0524:00 that cannot be cleared by itself, and the check engine light stays on even if the detection condition has gone. P2096:00 - Air fuel too lean P2097:00 - Air fuel too rich P0524:00 - Engine oil pressure too low. This concern may be caused by improper PCM control logic. The PCM software has been modified to eliminate this concern.
NHTSA · نشرة المصنع10180595سنوات الطراز 2019معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
New IDs software version 102.00 and Update 102.01 is now available on MS3 IDs update 102.00 and 102.01 is now available on MS3 under the "IDs/Infotainment" tab.
NHTSA · نشرة المصنع10186918سنوات الطراز 2017معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Active driving display opens/closes improperly. Some vehicles may exhibit the active driving display opening/closing improperly as described below: * It does not open or close when the ignition is turned ON or OFF . * The display operation does not fully open/close. * It closes and then opens by itself while the vehicle is moving. This concern may be caused by voltage fluctuation to the act ive driving display which activates pinching detection. Customer having this concern should have their vehicle repaired using the following repair procedure.
NHTSA · نشرة المصنع10186257سنوات الطراز 2016معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Some customers may experience the active driving display (auto flip-up type) does not flip up and no DTC is stored. Due to improper assembly, a deformed bracket may cause a loose mesh between internal gears. To correct this issue, the active driving display has been changed.
NHTSA · نشرة المصنع10144332سنوات الطراز 2018معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
If the right-side bsm control module requires replacement for any repair, also replace the left side bsm control module to complete the radar aiming procedure (it is ok to replace the left bsm alone). Reason if the right-side bsm control module is replaced alone, automatic configuration is not performed due to a program error in the module. Because of this, the required bsm radar aiming cannot be performed. Automatic configuration as well as bsm radar aiming can be performed, if the left-side bsm control module is replaced alone or together with the right-side bsm control module.
NHTSA · نشرة المصنع10105642سنوات الطراز 2016معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
If the right-side bsm control module requires replacement for any repair, also replace the left side bsm control module to complete the radar aiming procedure (it is ok to replace the left bsm alone). Reason if the right-side bsm control module is replaced alone, automatic configuration is not performed due to a program error in the module. Because of this, the required bsm radar aiming cannot be performed. Automatic configuration as well as bsm radar aiming can be performed, if the left-side bsm control module is replaced alone or together with the right-side bsm control module.
NHTSA · نشرة المصنع10101468سنوات الطراز 2016معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
If the active driving display (ad-disp) unit requires removal, use caution when disconnecting/connecting the wiring harness. If the harness is not connected properly, the ad-disp may not operate.
NHTSA · نشرة المصنع10091601سنوات الطراز 2016معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
If the active driving display (ad-disp) unit requires removal, use caution when disconnecting/connecting the wiring harness. If the harness is not connected properly, the ad-disp may not operate.
NHTSA · نشرة المصنع10090667سنوات الطراز 2016معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Bsm radar aiming cannot be performed after right-side bsm control module replacement. If right-dide bsm control module requres replacement for any repair, also replace left side bsm control module to compelte the radar aiming procedure (it's ok to replace the left bsm alone). If the right-side bsm control module is replaced alone, "automatic configuration" is not performed due to program error in module. Because of this, the required "bsm radar aiming" cannot be performed. "automatic configuration" as well as "bsm radar aiming" can be performed if left-side bsm control module is replaced alone or together with right-side bsm control module.
NHTSA · نشرة المصنع10076685سنوات الطراز 2016معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Mazda: There is condensation and fog in the front and rear combination lights. *rm
NHTSA · نشرة المصنع10037655سنوات الطراز 2011معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
المصادر: NHTSA (الولايات المتحدة، ملك عام)، وزارة النقل الكندية (رخصة الحكومة المفتوحة – كندا)، DVSA (المملكة المتحدة، رخصة الحكومة المفتوحة 3.0)، RappelConso وSafety Gate الأوروبي (فرنسا، الرخصة المفتوحة 2.0)، ووزارة MLIT اليابانية (رخصة البيانات العامة 1.0)، ووزارة MOLIT الكورية (car.go.kr).