قراءة مجانية · حساب مجاني للمساهمةخليفة Anticars (2000)

Mazda Tribute

2000–2011 · 2 الأجيال · 19 أعطال موثّقة · 4 أسواق
الأجيال

النشرات الفنية (TSB) تعليمات إصلاح يرسلها المصنعون إلى وكلائهم بشأن مشكلات معروفة. ليست استدعاءات سلامة، لكنها كثيرًا ما تؤكد وجود عطل.

سنة الطراز
السوقالكلEUNAUK
Tribute II · 2007–2011
نشرةحرجالمحركNA

نشرة

On some vehicles, a sulfur smell or 'rotten egg' odor may be noticed coming from the exhaust system. The odor is usually noticed after a cold start, fast idle, extended periods of idling and full throttle acceleration. Sulfur smell is not an indication of an engine concern and will not cause reduced driveability or durability of the engine or any of its emission components. The sulfur smell or 'rotten egg' odor is caused by high amounts of sulfur in the gasoline being used in the vehicle. Sulfur is normally eliminated during the refining process, but the EPA regulation of sulfur in gasoline differs from state to state. Vehicles using fuel containing high amounts of sulfur will most likely emit sulfur smell from the exhaust system.When high sulfur fuel is burned, there is a chemical reaction in the catalytic converter causing the sulfur tooxidize. As the vehicle is driven, the oxidizing reaction odor in the converter will decrease with mileage and age.

NHTSA · نشرة المصنع10153311سنوات الطراز 2011معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Tribute II · 2007–2011
نشرةحرجالمحركNA

نشرة

On some vehicles, a sulfur smell or 'rotten egg' odor may be noticed coming from the exhaust system. The odor is usually noticed after a cold start, fast idle, extended periods of idling and full throttle acceleration. Sulfur smell is not an indication of an engine concern and will not cause reduced driveability or durability of the engine or any of its emission components. The sulfur smell or 'rotten egg' odor is caused by high amounts of sulfur in the gasoline being used in the vehicle. Sulfur is normally eliminated during the refining process, but the EPA regulation of sulfur in gasoline differs from state to state. Vehicles using fuel containing high amounts of sulfur will most likely emit sulfur smell from the exhaust system. When high sulfur fuel is burned, there is a chemical reaction in the catalytic converter causing the sulfur to oxidize. As the vehicle is driven, the oxidizing reaction odor in the converter will decrease with mileage and age.

NHTSA · نشرة المصنع10145242سنوات الطراز 2011معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Tribute II · 2007–2011
نشرةمتوسطأخرىNA

نشرة

في إطار دعم توزيع MRT الجديد، ستشحن Mazda إلى الوكلاء جهاز كشف التسربات التشخيصي متعدد الأغراض الجديد بدءًا من شهر مارس 2019. وسيتم نشر مقاطع الفيديو التدريبية على MGSS قريبًا، وستُراجع إجراءات دليل الورشة تدريجيًا.

NHTSA · نشرة المصنع10154879سنوات الطراز 2011ترجمة آلية · اللغة الأصلية: الإنجليزيةعرض التفاصيل →
Tribute II · 2007–2011
نشرةمتوسطالتعليقNA

نشرة

إذا كانت المركبة تعاني من اهتزاز في الهيكل أو رجفة في عجلة القيادة أثناء القيادة، وتبيّن أن السبب الجذري هو توازن الإطارات، فأعد موازنة الإطارات باستخدام جهاز الموازنة Hunter GSP9700 أو ما يعادله. إذا لم يكن لدى الوكيل جهاز GSP9700 أو جهاز موازنة معادل له، فقم بإحالة المركبة إلى جهة أخرى للإصلاح. للعثور على موقع جهاز GSP9700 القريب من الوكيل، زر موقع Hunter الإلكتروني على الرابط www.gsp9700.com وانقر على “Locate a GSP9700 Road Force Balancer”.

NHTSA · نشرة المصنع10154139سنوات الطراز 2011ترجمة آلية · اللغة الأصلية: الإنجليزيةعرض التفاصيل →
Tribute II · 2007–2011
نشرةمتوسطأخرىNA

نشرة

This service bulletin provides information regarding the proper use of the driver's floor mat to avoid anypotential interference with the foot pedals. The following are possible causes of floor mat interference,which can be avoided with proper usage. Floor mat moves forward due to improper installation. Inappropriate floor mat (such as aftermarket, non-factory-equipped, or non-genuine) is used. Floor mat is stacked one on top of another.

NHTSA · نشرة المصنع10153331سنوات الطراز 2011معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Tribute II · 2007–2011
نشرةمتوسطالتعليقNA

نشرة

Some customers may complain that the steering wheel is off center more than 3 even when driving straight on a flat road.

NHTSA · نشرة المصنع10153318سنوات الطراز 2011معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Tribute II · 2007–2011
نشرةمتوسطالفراملNA

نشرة

Mazda North American Operations has approved an additional on-car brake lathe as an option for MNAO authorized equipment. The Pro-Cut On-Car Brake Lathe has been added to the MNAO authorized equipment program. NOTE: Accu-turn is still an approved brake lathe, but it is no longer available for purchase from our vendor. IMPORTANT: Rotors must be machined using a Mazda approved on-car brake lathe, or warranty claims are subject to denial or debit. Tool Number Description Pricing PC1923MAZ Pro-Cut On-Car Brake Lathe Check eStore or call for current pricing OBTAINING TOOLS This tool can be ordered through Mazda eStore. You can log on to eStore at: http://dealers.mazdausa.com CUSTOMER SERVICE INFORMATION For warranty or product information contact Mazda Authorized Service Equipment at 877-768-6657. Customer service representatives are available from 7:30 AM until 7:00 PM CST, Monday through Friday. SPECIAL SERVICE TOOL (SST) PART NAME: OVERVIEW Pro-Cut On-Car Brake Lathe PART NUMBER: PC1923MAZ APPLICABLE MODELS: All USAGE: To machine brake rotors on the vehicle.

NHTSA · نشرة المصنع10153307سنوات الطراز 2011معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Tribute II · 2007–2011
نشرةمتوسطالفراملNA

نشرة

Mazda North American Operations has approved an additional on-car brake lathe as an option for MNAO authorized equipment. The Pro-Cut On-Car Brake Lathe has been added to the MNAO authorized equipment program. NOTE: Accu-turn is still an approved brake lathe, but it is no longer available for purchase from our vendor. IMPORTANT: Rotors must be machined using a Mazda approved on-car brake lathe, or warranty claims are subject to denial or debit.

NHTSA · نشرة المصنع10148003سنوات الطراز 2011معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Tribute II · 2007–2011
نشرةمتوسطالفراملNA

نشرة

Mazda North American Operations has approved an additional on-car brake lathe as an option for MNAOauthorized equipment. The Pro-Cut On-Car Brake Lathe has been added to the MNAO authorizedequipment program.NOTE: Accu-turn is still an approved brake lathe, but it is no longer available for purchase from our vendor. IMPORTANT: Rotors must be machined using a Mazda approved on-car brake lathe, or warranty claimsare subject to denial or debit.

NHTSA · نشرة المصنع10142515سنوات الطراز 2011معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Tribute II · 2007–2011
نشرةمتوسطالتعليقNA

نشرة

Some customers may complain that the steering wheel is off center more than 3 even when driving straight on a flat road.

NHTSA · نشرة المصنع10142519سنوات الطراز 2011معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Tribute II · 2007–2011
نشرةمتوسطأخرىNA

نشرة

This service bulletin provides information regarding the proper use of the driver's floor mat to avoid any potential interference with the foot pedals. The following are possible causes of floor mat interference, which can be avoided with proper usage. Floor mat moves forward due to improper installation. Inappropriate floor mat (such as aftermarket, non-factory-equipped, or non-genuine) is used. Floor mat is stacked one on top of another. Use these points at your dealership to protect our mutual operations and to help ensure our customers' safety.

NHTSA · نشرة المصنع10134703سنوات الطراز 2011معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Tribute II · 2007–2011
نشرةمتوسطالهيكلNA

نشرة

When dealing with customer complaints of excessive condensation and/or water within the headlamp unit, first determine if all the bulb sockets (including O-ring), seals and covers are present and correctly installed. In most cases you will find that the Bulb Seal No. 1 (A) or HID Bulb Seal No. 1 (B) and Bulb Seal No. 2 (C) socket covers have not been correctly installed or are missing due to improper prior repairs (i.e., customer replacing the headlamp bulbs or body shop not transferring them when replacing the headlamp unit(s) due to a collision). Any damage caused by missing socket covers, HID module seal (D), or missing bumper brackets (E) is not covered by warranty policy.

NHTSA · نشرة المصنع10118468سنوات الطراز 2011معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Tribute II · 2007–2011
نشرةمتوسطالفراملNA

نشرة

Mazda Motor Corporation has decided to conduct a Special Service Program (SSP) on certain 2009-2011 Tribute vehicles. On certain 2009-2011 Tribute vehicles, contamination on the internal motor contacts of the throttle body may result in intermittent electrical connectivity.If this condition is present, the Malfunction Indicator Lamp or Wrench Lamp will illuminate, and the vehicle may enter fail-safe mode. In this mode, the engine power and vehicle speed is reduced, while maintaining full functionality of the power steering, power braking, lighting, and climate control systems. To improve vehicle performance should the above problem occur, dealers must reprogram the Powertrain Control Module (PCM). Please refer to Attachment II for repair details.This SSP will be in effect until July 31, 2015 regardless of mileage.

NHTSA · نشرة المصنع10117770سنوات الطراز 2011معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Tribute II · 2007–2011
نشرةمتوسطالفراملNA

نشرة

Mazda Motor Corporation is extending the warranty coverage for throttle body replacement on certain 2009-2011 Tribute vehicles produced from April 14, 2008 through May 30, 2011. The warranty for throttle body replacement will be extended to 10 years (120 months) from the original warranty start date or 150,000 miles, whichever comes first. If a vehicle has already exceeded the time or mileage limits, this coverage will last through January 31, 2015. Affected vehicles may develop contamination on the internal motor contacts of the throttle body, resulting in intermittent electrical connectivity. If this condition is present, the Malfunction Indicator Lamp (MIL) or Wrench light will illuminate and the vehicle may enter a fail-safe mode. In this mode, engine power and vehicle speed are reduced, while full functionality of the power steering, power braking, lighting, and climate control systems are maintained. If diagnosis identifies the throttle body as the causal component, dealers are authorized to replace the throttle body under this warranty extension program.This service must be performed at no charge to the vehicle owner.

NHTSA · نشرة المصنع10117771سنوات الطراز 2011معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Tribute II · 2007–2011
نشرةمتوسطالهيكلNA

نشرة

When dealing with customer complaints of excessive condensation and/or water within the headlamp unit, first determine if all the bulb sockets are resent and correctly installed. In most cases you will find that the bulb seal no. 1 (a) or hid bulb seal no. 1 (b) and bulb seal no. 2 (c) socket overs have not been correctly installed or are missing due to improper prior repairs (i.E., customer replacing the headlamp bulbs or body shop not transferring them when replacing the headlamp unit(s) due to a collision). Any damage caused by missing socket covers, hid module seal (d), or missing bumper brackets (e) is not covered by warranty policy.

NHTSA · نشرة المصنع10105886سنوات الطراز 2011معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Tribute II · 2007–2011
نشرةمتوسطالتعليقNA

نشرة

Some customers may complain that the steering wheel is off center more than 3 even when driving straight on a flat road.

NHTSA · نشرة المصنع10101062سنوات الطراز 2011معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Tribute II · 2007–2011
نشرةمتوسطالهيكلNA

نشرة

When dealing with customer complaints of excessive condensation and/or water within the headlamp unit, first determine if all the bulb sockets are present and correctly installed. In most cases you will find that the bulb seal no. 1 (a) or hid bulb seal no. 1 (b) and bulb seal no. 2 (c) socket covers have not been correctly installed or are missing due to improper prior repairs (i.E., customer replacing the headlamp bulbs or body shop not transferring them when replacing the headlamp unit(s) due to a collision). Any damage caused by missing socket covers, hid module seal (d), or missing bumper brackets (e) is not covered by warranty policy.

NHTSA · نشرة المصنع10098885سنوات الطراز 2011معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Tribute II · 2007–2011
نشرةمتوسطالتعليقNA

نشرة

Bulletin noteservice bulletin 06-001/14, 2008-2011 tribute - dtc b2278 stored in the power steering control module, is no longer valid. Service bulletin 06-001/14 has been superseded by safety recall 7614e, 2008-2011 tribute - electric power-assisted steering (epas).

NHTSA · نشرة المصنع10098346سنوات الطراز 2011معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Tribute II · 2007–2011
نشرةمتوسطأخرىNA

نشرة

This service bulletin provides information regarding the proper use of the drivers floor mat to avoid any potential interference with the foot pedals. The following are possible causes of floor mat interference, which can be avoided with proper usage. Floor mat moves forward due to improper installation. Inappropriate floor mat (such as aftermarket, non-factory-equipped, or non-genuine) is used. Floor mat is stacked one on top of another.

NHTSA · نشرة المصنع10098282سنوات الطراز 2011معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Tribute II · 2007–2011
نشرةمتوسطالفراملNA

نشرة

Mazda north american operations received many requests from our dealers asking us to approve additional on-car brake lathes as an option for mnao authorized equipment. Due to your feedback and after evaluating a few on-car brake lathes, we are pleased to announce that we have added the pro cut on-car brake lathe to mnao authorized equipment program. The accu-turn is still an approved brake lathe but it is no longer available for purchase from our vendor. Important reminder rotors must be machined using a mazda approved on-car brake lathe or warranty claims are subject to denial or debit.

NHTSA · نشرة المصنع10098245سنوات الطراز 2011معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Tribute II · 2007–2011
نشرةمتوسطأخرىNA

نشرة

Some vehicles may exhibit an intermittent no crank, no start condition with no diagnostic trouble codes (dtc) or passive anti-theft system (pats) indicator flashing.

NHTSA · نشرة المصنع10097806سنوات الطراز 2010–2011معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Tribute II · 2007–2011
نشرةمتوسطناقل الحركةNA

نشرة

Some vehicles equipped with an automatic transmission gain enhanced flat tow performance with an optional transmission cooling pump kit for recreational towing. The kit is available from the parts department and will help prevent transmission overheating.

NHTSA · نشرة المصنع10097804سنوات الطراز 2011معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Tribute II · 2007–2011
نشرةمتوسطناقل الحركةNA

نشرة

Some vehicles may exhibit an occasional fluid leak coming from the rear differential vent cap in temperatures below 32 degrees fahrenheit (0 degrees celsius) under certain conditions.

NHTSA · نشرة المصنع10097801سنوات الطراز 2011معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Tribute II · 2007–2011
نشرةمتوسطالتعليقNA

نشرة

Some customers may complain that the steering wheel is off center more than 3 even when driving straight on a flat road.

NHTSA · نشرة المصنع10097722سنوات الطراز 2011معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Tribute II · 2007–2011
نشرةمتوسطالتعليقNA

نشرة

Some customers may complain that the steering wheel is off center more than 3 even when driving straight on a flat road.

NHTSA · نشرة المصنع10097377سنوات الطراز 2011معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
الأقدم →

المصادر: NHTSA (الولايات المتحدة، ملك عام)، وزارة النقل الكندية (رخصة الحكومة المفتوحة – كندا)، DVSA (المملكة المتحدة، رخصة الحكومة المفتوحة 3.0)، RappelConso وSafety Gate الأوروبي (فرنسا، الرخصة المفتوحة 2.0)، ووزارة MLIT اليابانية (رخصة البيانات العامة 1.0)، ووزارة MOLIT الكورية (car.go.kr).