Bulletin
After replacement of the Integrated Braking system (IB)/Power Brake the total distance covered might belower than when handed over to the workshop for the repair.
🔔 Kostenloses Konto anlegen und Benachrichtigungen zu BMW XM erhalten
Technische Bulletins (TSB) sind Reparaturanweisungen, die Hersteller ihren Händlern zu bekannten Problemen schicken. Sie sind keine Sicherheitsrückrufe, bestätigen aber oft einen Mangel.
After replacement of the Integrated Braking system (IB)/Power Brake the total distance covered might belower than when handed over to the workshop for the repair.
Due to an implementation error in various OBD diagnostics in the vehicle's control units, in very rare cases itmay happen that stored fault memory codes (DTCs) and the MIL (warning light) are not automaticallydeleted even though the underlying malfunction has already been rectified. This does not comply with the statutory OBD specifications.
When turning the steering wheel while stationary or when driving on uneven roads; cracking, creaking, or knocking noises may be heard.
Several complaints are possible: Vehicle does not start Gear cannot be engaged Various Check Control Messages Malfunction indicator lamp (MIL) on Several Check Control messages are possible: It is possible to continue driving. High-voltage system. You can continue driving. Drivetrain. Restart not possible. Drivetrain fault. Call Roadside Assistance. Drivetrain failure. Information: Total error of vehicle. The following fault memory entries are stored in the CCU: D796D9 - Message (- 0x91) not up-to-date, receiver CCU, transmitter EME D796DC - No message (- 0x91), receiver CCU, transmitter EME D796D8 - No message (- 0x91), receiver CCU, transmitter EME Other fault codes below may be stored in the EGS BA09B8 Inverter, Voltage Sensor, 5V HV AUX: Out of range or open connection detected BA0A45 ECU internal: Internal error of the synchronous serial data bus. Additional fault memory entries are possible. Similar fault memory entries indicating a missing EMEmessage (Traction E-Machine Electronic) can also be stored in other control units.
In some situations, an emergency call may be triggered in the vehicle without either the customer pressing the SOS Call button, or an airbag deployment event. In some cases, the customer may not even be inside the vehicle.
Beim Lenken im Stand oder bei der Fahrt auf unebenen Straßen können knackende, knarrende oder klopfende Geräusche zu hören sein.
The seat lumbar system Massage will not function if the module needs to be initialized. This can occur toeither the drivers and/or passenger side seat. Here is a list of possible faults: Seat pneumatics module front right SPNM _ VR 025908 - SPNMVR: Control unit is not coded 02590B - SPNMVR: Control unit is not encoded for the vehicle 806927 - SPNMVR: Installation location not taught in Seat pneumatics module front left SPNM _ VL 025308 - SPNMVL: Control unit is not coded 02530B - SPNMVL: Control unit is not encoded for the vehicle 8067A7 - SPNMVL: Installation location not taught in Seat Module Driver FAS SMFA 80301E - No seat adjustment because of engine start conditions Seat Module Passenger BFS SMBF 802C1E - No seat adjustment because of engine start conditions Seat Module Drivers Side Rear FAH SMFAH 802E1E - No seat adjustment because of engine start conditions Seat Module Passenger Side Rear BFH SMBFH 802A1E - No seat adjustment because of engine start conditions
When making a call through the vehicle systems with a connected mobile device, electrical interference noise from accelerating or braking is heard by the other party (recipient). No interference can be heard in thevehicle.
After programming from the I-Levels between 24-03-505 and lower than 24-03-540 to I-Level 24-11-530 or higher, the following CCM may be displayed: CCM-2525: Brake system. Drive at moderate speed
When navigation is selected, only the start animation with the text Starting navigation system... isdisplayed. The Navigation application does not start. This only applies to vehicles where Navigation hasbeen enabled and has been verified to work previously.
A loud click- type noise can be heard from the rear axle brakes when driving off forwards, and/or in reverse.
After replacement of the Integrated Braking system (IB)/Power Brake the total distance covered might be lower than when handed over to the workshop for the repair.
After replacement of the Integrated Braking system (IB)/Power Brake the total distance covered might be lower than when handed over to the workshop for the repair.
Improved diagnostic software for the brake system.
Improved diagnostic software for the brake system.
At low outside temperatures (below 40 degrees F) and slow driving speeds (i.e. when parking, maneuvering)with a large steering angle, the front end can be slightly axially misaligned.
?BMW AG has issued a Delivery Stop (effective July 12, 2023) on certain Model Year 2023 - 2024 BMW vehicles that were produced between July 21, 2022, and July 11, 2023. A software logic error in the diagnostic module for tank leaks (DMTL) could cause the Service Engine Soon light (MIL) to not turn on when there is an electrical fault with pump or diverter valve for the DMTL even after several driving cycles with the fault/s being currently present.
BMW AG has issued a Delivery Stop (effective July 12, 2023) on certain Model Year 2023 - 2024 BMW vehicles that were produced between July 21, 2022, and July 11, 2023. A software logic error in the diagnostic module for tank leaks (DMTL) could cause the Service Engine Soon light (MIL) to not turn on when there is an electrical fault with pump or diverter valve for the DMTL even after several driving cycles with the fault/s being currently present.
Feuchtigkeit, Kondensation und/oder Beschlagen sind in einer oder beiden Oberscheinwerfern der Tagfahrscheinwerfer (DRL) sichtbar.
Nach der Programmierung des Fahrzeugs über ISTA/RSUto I-Level 26-03-5xx kann der Kunde berichten, dass einige der Innenumgebungsbeleuchtungsstreifen (Pfeile) nach einem tiefen Schlafzyklus sporadisch ausfallen. Dieses Problem ist vorübergehend und die Innenumgebungsbeleuchtung wird nach dem Verriegeln/Entriegeln des Fahrzeugs oder einer Änderung der Farbauswahl von selbst wiederhergestellt.
Aufgrund ungünstiger Software zeigt die Storage Management Electronics (SME) keine Fehlercodes an, die die Malfunction Indicator Lampe (MIL) auslösen, wenn die ISTA-Servicefunktion "Display Permanent SAE Fault Codes" ausgeführt wird. Daher müssen Werkstätten SME-spezifische permanente SAE-(emissionsbezogene) Diagnosefehlercodes (DTCs) identifizieren, die im Fahrzeug während der Diagnose oder bei der Vorbereitung eines Fahrzeugs auf eine staatliche Emissionsinspektion und Wartung gespeichert sind, durch ein Umgehungsverfahren.
Befestigungselemente Rücksendung
Fan Return
After programming the vehicle via ISTA/RSUto I-level 26-03-5xx, some of the interiorambient lighting strips (arrows) may begin tofail sporadically after a deep sleep cycle.
This Service Bulletin provides instructions to clean the intake valves using the BMW Carbon Blaster Tool P/N 81 29 2 208 034 and the S68T / XB1T Kit P/N 83 30 5 BAD 3D5. Refer to SI B04 12 11 for existing documentation about the carbon blaster tool and SI B04 02 26 for the S68T /XB1T tool kit.
Quellen: NHTSA (USA, gemeinfrei), Transport Canada (Open Government Licence – Canada), DVSA (Vereinigtes Königreich, Open Government Licence v3.0), RappelConso und EU-Safety-Gate (Frankreich, Licence Ouverte 2.0), MLIT (Japan, Public Data License 1.0) und MOLIT (Südkorea, car.go.kr).