Bei bestimmten Personenkraftfahrzeugen. Wenn der Motor nicht startet und der Fahrer den Schlüssel über längere Zeit in der "Start"-Position hält, fließt ein hoher Strom durch den Zündschalter und erzeugt manchmal genug Wärme, um innere Schalterteile zu schmelzen.
Bestimmte Fahrzeuge können nach erheblichen Wassermengen entweder den vorderen Airbag des Fahrers oder Beifahrers auslösen, ohne dass es zu einem Unfall kommt. Das Handbuch dieser Fahrzeuge enthält keine spezifischen Informationen zu dieser Situation. Ein unbeabsichtigtes Auslösen des Fahrer- und/oder Beifahrerairbags vorne in einer Nicht-Unfallsituation (nicht mit Aufprall) kann die Umgebung des Fahrzeugs (Windschutzscheibe / Instrumentenbrett) schädigen und teure Reparaturen verursachen, einschließlich des Austauschs des Airbagmoduls und des Sensing and Diagnostic Module (SDM). In einigen Fällen kann ein unbeabsichtigtes Auslösen leichte Verletzungen der Fahrzeuginsassen verursachen. Korrektur: GM wird die Besitzer dieser Fahrzeuge von 1996 und 1997 über die möglichen Auswirkungen von Wasseransammlungen im Fahrzeuginneren auf die Funktion des Airbagsystems informieren (wie in den Handbüchern der Fahrzeuge von 1998 und späteren Modelljahren enthalten).
Transport Canada24. Juni 20032003162Modelljahre 1996–1997Automatisch übersetzt · Original: EnglischDetails ansehen →
Bei bestimmten Personenkraftfahrzeugen. Wenn der Motor nicht startet und der Fahrer den Schlüssel über längere Zeit in der "Start"-Position hält, fließt ein hoher Strom durch den Zündschalter und erzeugt manchmal genug Wärme, um innere Schalterteile zu schmelzen.
Vehicle description: Passenger vehicles. If the engine starter fails to engage and the driver hold the key in the "start" position for an extended period, high current flows through the ignition switch, producing heat that can melt switch parts.
The protective cover for the underhood fuse centre may have been omitted on these vehicles. Without this cover, the positive terminal bolt on the fuse block is exposed, and may come in contact with the insulated negative battery cable. Prolonged contact may result in abrasion of the negative cable insulation and could cause an extremely high current short circuit between the positive terminal and the negative cable. This current flow could cause arcing and result in an underhood fire. Correction: A protective cover will be installed if necessary.
Transport Canada14. Apr. 19971997078Modelljahre 1997Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
The protective cover for the underhood fuse center was omitted. Without this cover, the positive terminal bolt on the fuse block is exposed and can contact the insulated negative battery cable. If the insulation on the negative cable becomes sufficiently worn, an electrical short circuit can occur between the positive terminal and negative cable resulting in extremely high current flow.
The steering column lower pinch bolt may not have been torqued to specification. This could result in rattle and looseness in the steering system. If the pinch bolt were backed out of the joint completely, rotation of the steering shaft against the connector in high effort steering maneuvers could cause increasing looseness in the steering system and could result in loss of steering and a crash. Correction: Steering column pinch bolt will be inspected and if necessary tightened to specified torque.
Transport Canada13. Dez. 19961996206Modelljahre 1996Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
These vehicles may not comply with c.M.V.S.S. 301 - fuel system integrity. Some welds in the left rear quarter panel may have been missed during assembly. In the event of a vehicle crash, the vehicle sheet metal structure may not perform as designed. This could result in unexpected damage to the fuel tank or fuel lines and leakage of fuel. If there is a fuel leak and an ignition source, a fire could occur. Correction: Dealers will inspect for missing welds and, if necessary, place three welds between the involved panels.
Transport Canada30. Okt. 19961996173Modelljahre 1997Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
During assembly of the left rear quarter panel, some welds were missed. This does not comply with the requirements of fmvss no. 301, "fuel system integrity."
These vehicles were constructed with welds in the rear compartment pan assembly that are not sufficient to comply with the requirements pertaining to fuel tank leakage in the event of a rear impact collision. The fuel tank assemblies do not comply with fmvss no. 301, "fuel system integrity."
NHTSA · USA1. Juli 199494V122000Modelljahre 1994Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Front fuel feed hose assembly could crack or separate at the coupling on the engine end of the hose assembly, allowing fuel to leak into the engine compartment.
Moisture can enter the express-down electronic control module and cause a short circuit that causes window operation without operator control, and leaves the window in the down position.
On vehicles with power windows, moisture may enter the express-down electronic control module and could cause phantom window operation in which the window may cycle without operator input and sometimes remain down. The module may eventually fail by overheating, which could result in a fire in the door panel. Correction: Dealers will replace the power window express-down electronic control module.
Transport Canada24. März 19921992032Modelljahre 1991Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
The daytime running light (drl) module, which is located near the battery, could overheat and possibly result in an underhood fire. Correction: Dealers will replace the drl module, install a wiring harness with fuses and install a module cover.
Transport Canada20. Aug. 19901990126Modelljahre 1990Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Vehicles may have improperly torqued connections of the front fuel feed/return hoses to the fuel pipes at the body rail. A fitting may loosen enough to leak fuel into the underhood area, and, in the presence of an ignition source, a fire could result. Correction: Front fuel feed/return hose fittings will be properly torqued.
Transport Canada11. Juni 19901990083Modelljahre 1990Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
On vehicles with quad 4 engines, the front fuel feed assembly could crack or separate at the coupling on the engine end of the assembly, allowing fuel to leak into the underhood area. This would create the possibility of an engine compartment fire. Correction: Front fuel feed hose assembly will be replaced on affected vehicles.
Transport Canada7. März 19901990043Modelljahre 1988–1989Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Front fuel feed hose assembly could crack or separate at the coupling on the engine end of the hose assembly, allowing fuel to leak into the engine compartment.
NHTSA · USA5. März 199090V042000Modelljahre 1988–1989Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Bei Fahrzeugen mit 2,5-Liter-Motoren. Das Kraftstoffsystem kann an der Einspritzverbindung des Drosselklappenhauses undicht werden, was die Gefahr eines Brandes unter der Haube darstellt.
Transport Canada29. März 19851985032Modelljahre 1984Automatisch übersetzt · Original: EnglischDetails ansehen →
Das Kraftstoffsystem kann an der Verbindung der Gasklappeneinspritzung und der Kraftstoffzufuhrleitung undicht werden. Folge des Defekts: Dieses Leck könnte zu einem Brand unter der Motorhaube führen, der sich auf den Fahrgastraum ausbreitet und Verbrennungen bei den Insassen verursacht.
Die Befestigungsschrauben des hinteren Querarmhalters, die bei bestimmten dieser Fahrzeuge verwendet werden, können brechen. Ein Ausfall aller vier Schrauben auf einer Seite kann dazu führen, dass der Querlenker so weit absinkt, dass der hintere Bremsschlauch durchtrennt wird. Ein solcher Schnitt führt zu Flüssigkeitsverlust und teilweisen Bremswirkungsverlusten. Dies führt zu vergrößerten Bremswegen, und sollte ein Ausfall während der Fahrt des Fahrzeugs zu einer Zeit mit minimalen Bremsabständen auftreten, kann es zu einem Unfall kommen.
The rear axle control arm locates and helps control axle movement; it attaches to the frame with a bracket. The rear control arm bracket attaching bolts used on some of the involved vehicles may fracture. Fracture of all four bolts on one side of the vehicle can result in the control arm dropping enough to cut the rear brake hose. A severed brake hose would result in brake fluid loss and partial loss of braking ability.
The brake proportioner valves may break and separate from the master cylinder during braking. This will result in a loss of brake fluid and a partial loss of braking action
Transport Canada7. Okt. 19841983084Modelljahre 1983Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Quellen: NHTSA (USA, gemeinfrei), Transport Canada (Open Government Licence – Canada), DVSA (Vereinigtes Königreich, Open Government Licence v3.0), RappelConso und EU-Safety-Gate (Frankreich, Licence Ouverte 2.0), MLIT (Japan, Public Data License 1.0) und MOLIT (Südkorea, car.go.kr).