Bulletin
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear.
Technische Bulletins (TSB) sind Reparaturanweisungen, die Hersteller ihren Händlern zu bekannten Problemen schicken. Sie sind keine Sicherheitsrückrufe, bestätigen aber oft einen Mangel.
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear.
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear.
Diese technische Mitteilung beschreibt ein Verfahren zur Prüfung auf überschüssiges Fett oder Dichtmittel an der Außenseite des Lenkgetriebes, da an bestimmten Stellen des Getriebes Fett oder Dichtmittel sichtbar ist.
This technical bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear.
This informational bulletin provides a revision for 09-06-04-015B (Vehicles Sitting Outside on Dealer Lots for Extended Periods with Hard Start/No Start Condition) to add the 2015-2018 model years.
This informational bulletin provides information on installing the correct tires for vehicles with the condition of under hard acceleration at higher speeds, the traction control light will flash. Or, they may come in for ABS or general handling/braking concerns.
This technical bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear.
This Preliminary Information communication provides information to the technician about vehicles that after installing a reman High Value V6 engine it has rough running, idle surge, misfire on one or both banks of the engine concern. Technician may find Diagnostic Trouble Codes P0300, P0011 and / or P0016. Technician will need to check the actual engine oil pressure. If oil pressure is within the specifications above, perform all testing listed in PIP4345A including a visual inspection of the camshaft position actuator filter and repair or replace as necessary. Technician will need to contact General Motors Technical Assistance Center for further assistance if the concern is still present.
This Preliminary Information communication provides information to the technician that after installing a re-manufactured High Feature V6 engine the vehicle may rough running, idle surge, Check Engine Lamp or Camshaft Position sensor actuator codes. Technician will need to record the actual engine oil pressure at idle and engine compression readings. Technician will need to perform all testing listed in PIP4345A, if oil pressure and compression readings are within specifications. Technician will need to contact General Motors Technical Assistance Center for further assistance if the concern is not isolated.
This preliminary information communication advises the technician on the steps to diagnose the concern, and the steps to repair the concern of the vehicle cranks but does not start. The technician is to inspect for a sheared cam pin in the engine.
"this technical bulletin provides a procedure to inspect the steering gear for a normal condition of grease or sealant on exterior case of gear due to the manufacturing process."
Ölleck an der Kurbelwellen-/Riemenscheibendichtung. *tt
Rear main oil seal leak. *tt
Keine Bewegung und/oder Getriebeölaustritt am rechten inneren Tripode – rechte Antriebswelle nicht richtig eingesetzt. *tt
A stall and/or no crank, no start condition after the wipers are used. The service engine soon light may or may not be illuminated and the customer may report other problems with the cruise control system. A tech 2 diagnostic probe will find numerous dtcs which could include p0608 cruise control, c0460, c0461 steering wheel sensor codes, and possibly a no communication issue with the pcm. Engineering has determined the wiper motor crank arm is contacting the ubec wiring harness and cutting the wires. *tt
Revised camshaft position actuator fastener installation procedure. *tt
Stall, no crank, no start after using the wipers. *tt
Supplement to sit-n-lift seat installation instructions. *tt
Rear disc brake drag or continuing to hold. *tt
Crank, no start condition with no spark. *tt
This service bulletin describes the U.S. Dealer Special Tool Loan Program process.
Dieses vorläufige Informationsbulletin (PI) stellt Händlerpersonal Informationen zur Verfügung, die beim Umgang mit Korrosion an Unterbodenkomponenten im Gespräch mit Kunden hilfreich sein können.
Programmierung und Aktivierung von Ersatz-OnStar-Modulen.
Dieses Service-Bulletin beschreibt den Ablauf des Leihprogramms für Sonderwerkzeuge für Händler in den USA.
Dieses Servicebulletin informiert das Werkstattpersonal über Probleme beim Schalten des Automatikgetriebes und bei der Motorfahrbarkeit sowie über eingeschaltete Motorkontrollleuchte (MIL) infolge der Verwendung von Ölbad-Luftfiltern aus dem Zubehörhandel.
Quellen: NHTSA (USA, gemeinfrei), Transport Canada (Open Government Licence – Canada), DVSA (Vereinigtes Königreich, Open Government Licence v3.0), RappelConso und EU-Safety-Gate (Frankreich, Licence Ouverte 2.0), MLIT (Japan, Public Data License 1.0) und MOLIT (Südkorea, car.go.kr).