Frei lesbar · kostenloses Konto zum MitmachenNachfolger von Anticars (2000)

Ford Explorer V

2010–2019 · 15 dokumentierte Mängel · 5 Märkte

Technische Bulletins (TSB) sind Reparaturanweisungen, die Hersteller ihren Händlern zu bekannten Problemen schicken. Sie sind keine Sicherheitsrückrufe, bestätigen aber oft einen Mangel.

SchweregradAlleMittelGering
Modelljahr
MarktAlleNA
BulletinMittelElektrikNA

Bulletin

Einige 2018er Explorer/Police Interceptor Utility Fahrzeuge mit Police-, Base 100A- oder XLT 200A-Ausstattungsvarianten (Typ-1-Analogcluster im Benutzerhandbuch), die vom 08. Mai 2018 bis zum 05. August 2018 gebaut wurden, können einen parasitären Batterieverbrauch von etwa 250 Milliampere aufweisen, wobei das Instrumentenpanel (IPC) möglicherweise wach bleibt, ohne Schlüssel. Dies kann zu einem Zustand ohne Kurbelwelle/keinen Start oder Entladung der Batterie führen. Um das Problem zu beheben, programmieren Sie den IPC mit der neuesten Softwarestufe über das Integrated Diagnostic System (IDS) neu. Stellen Sie sicher, dass das Fahrzeug an ein Batterieladegerät angeschlossen ist. Für die Anmeldung verwenden Sie den Kausalteil 10849 und die entsprechenden Arbeitsabläufe in Abschnitt 10 des Service Labor Time Standards (SLTS) Manuals.

NHTSA · Herstellerbulletin10216541Modelljahre 2018Automatisch übersetzt · Original: EnglischDetails ansehen →
BulletinMittelElektrikNA

Bulletin

Some 2018 Explorer/Police Interceptor Utility vehicles equipped with Police, Base 100A, or XLT 200A package trim levels (Type 1 analog cluster in the Owner's Manual) built on 08-May-2018 and through 05-Aug-2018 may exhibit a parasitic battery drain of approximately 250 milliamps with the instrument panel cluster (IPC) possibly staying awake with the key off. This may result in a no crank/no start/discharged battery condition. To resolve the concern, reprogram the IPC using the latest software level of the appropriate Ford diagnostic scan tool. Make sure the vehicle is connected to a battery charger. For claiming, use causal part 10849 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

NHTSA · Herstellerbulletin10149757Modelljahre 2018Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelElektrikNA

Bulletin

Some 2018 Explorer/Police Interceptor Utility vehicles equipped with Police, Base 100A, or XLT 200A package trim levels (Type 1 analog cluster in the Owner's Manual) built on 08-May-2018 and through 05-Aug-2018 may exhibit a parasitic battery drain of approximately 250 milliamps with the instrument panel cluster (IPC) possibly staying awake with the key off. This may result in a no crank/no start/discharged battery condition. To resolve the concern, reprogram the IPC using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 10849 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

NHTSA · Herstellerbulletin10144946Modelljahre 2018Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelElektrikNA

Bulletin

Some 2018 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization and/or accessory protocol interface module (APIM) DTC U0198 or no modem electronic serial number (ESN) displayed. To correct this condition, remove the TCU fuse for 5 minutes then reinstall. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual (WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229.

NHTSA · Herstellerbulletin10137130Modelljahre 2018Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelElektrikNA

Bulletin

Some 2016-2017 Ford and Lincoln vehicles with SYNC 3 may exhibit an intermittent blue or black screen. Check for SYNC software update under the OASIS Tab SYNC selection. If update is available refer to WSM, Section 415-00 and update APIM software. After Installation Complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.

NHTSA · Herstellerbulletin10119678Modelljahre 2017Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelElektrikNA

Bulletin

Some 2016-2017 Ford/Lincoln vehicles SYNC 3 may exhibit an intermittent blank screen. Check for SYNC software update under the OASIS Tab SYNC selection. If update is available refer to WSM, Section 415-00 and update APIM software. During the update process the SYNC status bar shows Updating System Software for approximately 30 minutes. After Installation Complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or blank screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.

NHTSA · Herstellerbulletin10115952Modelljahre 2017Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinGeringElektrikNA

Bulletin

Some 2019 MKC, 2019-2021 Edge/Nautilus/Escape/Ranger/Explorer, 2020-2021 Corsair, and 2021 Bronco Sport vehicles equipped with 2.0L and 2.3L EcoBoost engines may exhibit a light to moderate ticking type noise at idle (600-700 RPM). The noise is usually more prominent in the area of the high-pressure fuel pump, located on the top of the engine just behind the number 4 ignition coil. This noise is not detrimental to engine function and has no short or long-term effects on engine durability. This an operating characteristic of these engines and no repairs should be attempted.

NHTSA · Herstellerbulletin10199497Modelljahre 2019Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinGeringElektrikNA

Bulletin

Some 2019 MKC, 2019-2020 Edge/Nautilus/Escape/Ranger, 2020 Corsair, 2019-2021 Explorer vehicles equipped with 2.0L and 2.3L EcoBoost engines may exhibit a light to moderate ticking type noise at idle (600-700 RPM). The noise is usually more prominent in the area of the high-pressure fuel pump, located on the top of the engine just behind the number 4 ignition coil. This noise is not detrimental to engine function and has no short or long-term effects on engine durability. This an operating characteristic of these engines and no repairs should be attempted.

NHTSA · Herstellerbulletin10183569Modelljahre 2019Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinGeringElektrikNA

Bulletin

Some 2018 EcoSport/Expedition/Explorer vehicles equipped with a telematics control unit (TCU) module may exhibit an inoperative remote start with a Vehicle Failed To Start message when using the Ford Pass mobile application. This message may be observed even if the vehicle has been driven immediately prior to the remote start request. Other functions such as remote lock and unlock from the Ford Pass mobile application will work as expected. Engineering is currently investigating this condition. Inform customers Ford is developing a software fix that is expected in early January. In the interim, let the customer know they can continue to drive the vehicle and schedule a follow-up appointment with the customer for early January. Once the update becomes available, contact the customer and confirm the service appointment is going forward. Monitor OASIS for updates.

NHTSA · Herstellerbulletin10181934Modelljahre 2018Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinGeringElektrikNA

Bulletin

Some 2018 Explorer, Expedition, F150 excluding Raptor fleet vehicles equipped with a telematics control unit (TCU) may exhibit incomplete Ford Telematics service subscription activation, inability to remotely interface with a vehicle, and/or not receiving fleet alerts. Reprogram the TCU using the appropriate Ford scan tool at the latest software level. Fleet vehicle and TCU type can be identified in the Vehicle Information section of OASIS. TCU will be listed as 4G SYNC Connect. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

NHTSA · Herstellerbulletin10149768Modelljahre 2018Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinGeringElektrikNA

Bulletin

Certain 2018 Model Year Explorer And Police Interceptor Utility Vehicles Key Off Load Battery Drain

NHTSA · Herstellerbulletin10149782Modelljahre 2018Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinGeringElektrikNA

Bulletin

Some 2018 Explorer vehicles equipped with a 4G TCU modem may exhibit an Acquiring Signal message with a loss of satellite radio reception while driving in unobstructed areas. If normal Workshop Manual (WSM) diagnosis and testing does not indicate a fault and no diagnostic trouble codes (DTCs) are stored, do not attempt any repairs at this time. Engineering is investigating, monitor OASIS for updates. To assist with the investigation, use the Report A Vehicle Concern link at the bottom of the OASIS report and complete the form.

NHTSA · Herstellerbulletin10144934Modelljahre 2018Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinGeringElektrikNA

Bulletin

Some 2018 Explorer and Escape vehicles equipped with a 4G TCU modem may exhibit an Acquiring Signal message with a loss of satellite radio reception while driving in unobstructed areas. If normal Workshop Manual (WSM) diagnosis and testing does not indicate a fault and no diagnostic trouble codes (DTCs) are stored, do not attempt any repairs at this time. Engineering is investigating, monitor OASIS for updates. To assist with the investigation, use the Report A Vehicle Concern link at the bottom of the OASIS report and complete the form.

NHTSA · Herstellerbulletin10144949Modelljahre 2018Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinGeringElektrikNA

Bulletin

Some 2016-2017 Ford and Lincoln vehicles with SYNC 3 may intermittently display an overhead image of a vehicle in the center of the SYNC touchscreen with no obstacle detection grids or warning chimes. SYNC may appear unresponsive when the overhead vehicle image is displayed. The vehicle image may intermittently display after shifting out of reverse or turning the vehicle off when in reverse. SYNC software updates are now available under the OASIS Tab SYNC selection. If an update is available, refer to WSM Section 415-00 and update the APIM software. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.

NHTSA · Herstellerbulletin10127424Modelljahre 2017Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinGeringElektrikNA

Bulletin

Some 2017 Explorer vehicles equipped with a 110V power inverter may exhibit a high pitched buzzing or ringing noise from the passenger side front interior area while the engine is running. To isolate the noise to the power inverter, remove fuse 56 from the battery junction box with the engine running. Make sure there is nothing plugged into the 110V outlet during the test. If the noise is no longer present with the fuse removed, the noise is isolated to the inverter and no other components should be replaced. Replacement of the inverter may not resolve the noise. Engineering is aware of the concern and is investigating. The noise does not affect the operation of the power inverter. Please submit a Global Concern Report and continue to monitor OASIS for updates.

NHTSA · Herstellerbulletin10125086Modelljahre 2017Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinGeringElektrikNA

Bulletin

Some 2016-2017 Escape, MKC, Fiesta, F150, Expedition, Navigator, Mustang, Transit, Focus, C-Max, MKX, Taurus, MKS, Flex, MKT, and Edge and 2017 Explorer, Fusion, MKZ, Super Duty, Transit Connect and Continental vehicles equipped with SYNC 3 might exhibit a blank screen or other various SYNC symptoms only when the vehicle is in Transport mode. Engineering is aware of this possibility and it is considered normal due to the power saving features enabled while in transportation mode. It is beneficial to extended battery life to keep the vehicle in Transport Mode until the vehicle is prepped for sale. If the vehicle should exhibit a blank screen or other SYNC symptoms after it has been taken out of Transport mode, refer to Workshop Manual, Section 415-00 for normal diagnosis. The SYNC version can be confirmed via OASIS.

NHTSA · Herstellerbulletin10109067Modelljahre 2017Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinGeringElektrikNA

Bulletin

Some 2016 Edge/Explorer/F-150/Mustang built on or before 01-Nov-2016 and equipped with a 4.2-inch FCDIM may exhibit a blank screen. To correct the concern, Reprogram the FCDIM to the latest level using IDS release 104.02 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. For claiming, use causal part 10D885 and applicable labor operations in section 10 of the service labor time standards (SLTS) manual.

NHTSA · Herstellerbulletin10109004Modelljahre 2016Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinGeringElektrikNA

Bulletin

Some 2016-2017 Edge, Escape, Expedition, Fiesta, Flex, MKC, MKT, MKX, Mustang, Navigator and Taurus or 2017 Explorer and Super Duty vehicles equipped with SYNC 3 and built on 1-Jul-2015 and through 31-Dec-2016 may exhibit a SYNC display message of Please check your surroundings for safety along with no rear view camera image when in reverse gear. This will occur only at ambient temperatures ranging from -5 'C to 5 'C (23 'F to 41 'F). This maybe due to a temperature dependent issue within the APIM crystal oscillator circuitry. Follow the Service Procedure steps to correct the condition.

NHTSA · Herstellerbulletin10109001Modelljahre 2017Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinGeringElektrikNA

Bulletin

Some 2016-2017 ford or lincoln vehicles equipped with sync 3 may exhibit a blank screen or other various sync symptoms only when the vehicle is in transport mode. This is considered normal due to the power saving features enabled while in transport mode. It is beneficial for battery life to keep the vehicle in transport mode until the vehicle is prepped for sale. To prevent a sync system lockup during transport mode deactivation, follow the workshop manual (wsm) procedure exactly allowing time for the sync system to complete its tasks such as fully booting up or powering down and shutting off before moving to the next step of the procedure. If the vehicle exhibits a blank screen or sync symptoms after transport mode deactivation, refer to wsm, section 415-00 for normal diagnosis. The sync version can be confirmed via oasis.

NHTSA · Herstellerbulletin10100508Modelljahre 2017Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinGeringElektrikNA

Bulletin

Some 2016 edge/explorer/f-150/mustang built on or before 01-nov-2016 and equipped with a 4.2-inch fcdim may exhibit a blank screen. To correct the concern, reprogram the fcdim to the latest level using ids release 104.02 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. For claiming, use causal part 10d885 and applicable labor operations in section 10 of the service labor time standards (slts) manual.

NHTSA · Herstellerbulletin10100067Modelljahre 2016Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinGeringElektrikNA

Bulletin

Some 2016 edge, f150, explorer, and mustang vehicles equipped with a myford display 4 inch screen may exhibit a blank screen and no audio. Reprogram the front control display interface module (fcdim) to the latest calibration using integrated diagnostic system (ids) release 104.01 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. Calibration files may also be obtained at www.Motorcraftservice.Com. Use causal part number 10d885 and applicable labor operations in section 10 of the service labor time standards (slts) manual.

NHTSA · Herstellerbulletin10095648Modelljahre 2016Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinGeringElektrikNA

Bulletin

Some 2016 escape/mkc/fiesta/f150/expedition/navigator/mustang /transit/focus/c-max/mkx/taurus/mks/flex/mkt/edge and 2017 escape/explorer/mkc/fusion and mkz vehicles equipped with sync 3 might exhibit a blank screen or other various sync symptoms only when the vehicle is in transport mode. Engineering is aware of this possibility and it is considered normal due to the power saving features enabled while in transportation mode. It is beneficial to extended battery life to keep the vehicle in transport mode until the vehicle is prepped for sale. If the vehicle should exhibit a blank screen or other sync symptoms after it has been taken out of transport mode, refer to workshop manual, section 415-00 for normal diagnosis. The sync version can be confirmed via oasis.

NHTSA · Herstellerbulletin10092402Modelljahre 2017Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinGeringElektrikNA

Bulletin

Some 2016 f150, mustang and explorer vehicles equipped with a 3.5l gtdi, 2.3l gtdi or 2.7l gtdi engine built on or before 4/15/2016, and equipped with active noise cancellation (anc) or engine sound enhancement (ese), may exhibit no audio and/or display an audio off or loading message after starting the engine. Reprogram the audio control module (acm) to the latest calibration using ids release 101.03 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. Calibration files may also be obtained at www.Motorcraftservice.Com. Use causal part number 18c869 and applicable labor operations in section 10 of the slts manual.

NHTSA · Herstellerbulletin10091432Modelljahre 2016Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinGeringElektrikNA

Bulletin

Some 2016 explorer vehicles built on or before 5/8/2016 may exhibit a noise from the electric cooling fans, most noticeable right after the engine is turned off as they spin down to a stop. If the noise can be pinpointed to the cooling fan motor, replace the cooling fan assembly with applicable updated service parts. Da8z-8c607-b replaced da8z-8c607-a, dg1z-8c607-e replaced dg1z-8c607-d, dg1z-8c607-f replaced dg1z-8c607-a, db5z-8c607-d replaced db5z-8c607-c. Refer to workshop manual (wsm,) section 303-03. Use available service labor times in section 08.

NHTSA · Herstellerbulletin10091275Modelljahre 2016Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinGeringElektrikNA

Bulletin

3.5l gasoline turbocharged direct injection (gtdi) engine may exhibit a malfunction indicator lamp (mil) with diagnostic trouble codes (dtc) p0327/p0332.

NHTSA · Herstellerbulletin10079008Modelljahre 2016Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Ältere →

Quellen: NHTSA (USA, gemeinfrei), Transport Canada (Open Government Licence – Canada), DVSA (Vereinigtes Königreich, Open Government Licence v3.0), RappelConso und EU-Safety-Gate (Frankreich, Licence Ouverte 2.0), MLIT (Japan, Public Data License 1.0) und MOLIT (Südkorea, car.go.kr).