Elektrik:Zündung
Der Zündschalter könnte einen internen Kurzschluss erleiden.
🔔 Kostenloses Konto anlegen und Benachrichtigungen zu Ford F-Series eighth generation erhalten
Der Zündschalter könnte einen internen Kurzschluss erleiden.
Im Zündschalter könnte ein Kurzschluss entstehen, der zu Überhitzung, Rauchentwicklung und möglicherweise zu einem Brand in der Lenksäule des Fahrzeugs führen kann. Dieser Zustand kann sowohl während der Fahrt als auch im unbeaufsichtigten Zustand des Fahrzeugs auftreten. Abhilfe: Der Zündschalter wird durch einen Zündschalter in überarbeiteter Konstruktion ersetzt.
Note: Vehicles equipped with 7.5 litre engines. The fuel return tube, which connects the frame fuel return line with the engine fuel rail, may contact the pinch weld flange connecting the dash panel to the floor pan. This could lead to abrasion of the steel tube and result in a fuel leak. Correction: Fuel return tubes will be replaced with flexible stainless steel braided/teflon lines and a vinyl guard will be installed on the body weld flange.
The steel fuel return tubes that connect the frame fuel return lines with the engine fuel rail can contact the pinch weld flange connecting the dash panel to the floor pan. Continued contact leads to abrasion of the steel fuel return tube and eventually results in a fuel leak.
A malfunctioning check valve within the fuel pump assembly causes a portion of the unused fuel from one tank to be returned to the second tank. When this occurs, the capacity of the second tank can be exceeded, causing fuel spillage.
Vehicles with gasoline engines and dual fuel tanks may experience the transfer of fuel from one tank to the other through a malfunctioning check valve within the fuel pump assembly. This could cause the capacity of the other tank to be exceeded, resulting in fuel overflow past the filler cap. In the presence of an ignition source, a fire could result. Correction: Fuel pressure regulator will be replaced and redundant check valves will be installed on affected vehicles.
Keys attached to the key ring of an ignition key while it is in the vehicle ignition can become lodged in the steering lock receiver as the steering wheel is being turned.
On vehicles with dual fuel tanks, the dual function fuel reservoir (dfr) may malfunction allowing supply fuel to be drawn from one tank and a portion of the unused fuel to be returned to the other tank. As a result, the other tank could possibly be overfilled, resulting in overflow of fuel past the filler cap. In the presence of an ignition source, the potential for a fire may exist. Correction: A dfr containing "o" rings manufactured from revised material will be installed on affected vehicles.
The dual fuel tank selector valve may malfunction and cause an overfill condition in one of the fuel tanks, resulting in an overflow of fuel past the filler cap.
Note: This recall supersedes recall 88164. Vehicles located in the yukon, nothwest territories, alberta, eastern british columbia, n.W. Ontario, manitoba and saskatchewan. A short, u-shaped nylon fuel tube (jumper tube) located on the left-hand frame rail connecting the fuel pump to the fuel filter could develop pin holes in the tubing wall. If this condition should occur, it would allow fuel to leak and a fire could result. Correction: A steel braided teflon fuel supply line and related components will be installed which will ground the fuel line and eliminate the potential for an electrostatic charge. The u-shaped nylon jumper tube will be eliminated by this replacement fuel system.
Incorrectly installed fuel line connectors have fuel supply and return lines crossed.
Bolts that attach the front axle track bar bracket to the front crossmember may loosen, allowing the front wheels to oscillate with front end shimmy.
A short, u-shaped nylon fuel tube (jumper tube) located on the left-hand frame rail connecting the fuel pump to the fuel filter could develop pin holes in the tubing wall. If this condition should occur, it would allow fuel to leak and a fire could result. Correction: Fuel tube will be replaced with one having a krayton sleeve.
Steering/suspension systems may not adequately control steering type wobble allowing the front end to shimmy.
Bei Fahrzeugen mit EFI oder CFI kann sich die Federring-Schnellkupplung der Kraftstoffleitung, die die Kraftstoffzufuhr- und Rücklaufleitungen mit den EFI-Kraftstoffverteilern bzw. den CFI-Drosselklappengehäusen verbindet, sowie andere Kraftstoffleitungsanschlüsse nahe der Armaturenbrettverkleidung bei einigen Fahrzeugen während des Fahrzeugbetriebs lösen. Tritt dies auf, kommt es zu einem Kraftstoffverlust, wodurch die Gefahr eines Fahrzeugbrands besteht. Korrektur: Bei betroffenen Fahrzeugen werden Haltklammern für die Kupplungen installiert. Hinweis: Escort-Fahrzeuge sind mit EFI und CFI ausgestattet. Lynx-Fahrzeuge sind nur mit CFI ausgestattet. EFI – Elektronische Kraftstoffeinspritzung CFI – Zentrale Kraftstoffeinspritzung
Wheel lug nut cone angles do not match lug nut seating angles.
Spring lock fuel line coupling may not be properly engaged.
Trucks fail to meet requirement of fmvss no. 301, fuel system integrity, in a 30 mph front angular barrier test impact because of the omission of the nose shield on midship fuel tank. Consequence of defect: In case of an accident, fuel spillage in the trucks which do not meet the fmvss increases the risk of a fire.
Bei einigen der betroffenen Fahrzeuge könnte ein Tempomat-Zug verbaut sein, der die Riemenscheibe des Tempomat-Servos behindern kann und dazu führt, dass das Gaspedal beim Ausschalten des Tempomats nicht in die Leerlaufstellung zurückkehren kann.
Hinweis: Betroffen sind auch einige mittelschwere und schwere Lkw. Diese Fahrzeuge erfüllen möglicherweise nicht die Anforderungen von C.M.V.S.S. 108 – Beleuchtung. Das Steuermodul für das Tagfahrlicht kann fehlerhaft arbeiten, wodurch sich die Tagfahrleuchten abschwächen, flackern oder ausgehen können oder in einigen Fällen nach dem Ausschalten der Zündung eingeschaltet bleiben. Korrektur: Das Steuermodul für das Tagfahrlicht wird bei betroffenen Fahrzeugen ersetzt.
Note: Vehicles with 7.3 litre diesel and 7.5 litre efi engines over 8500 lb. Gvwr and 4x4 models with 5.8 litre efi engines. When vehicles are operated at or near gvwr or gcwr (gross combination weight rating when trailer towing), brake effectiveness may diminish due to overheating of the front brakes. This may result in longer than normal stopping distances and a low brake pedal and could increase the risk of a vehicle crash. Correction: Snap-in insulators that attach to each of the front brake caliper pistons will be installed on all affected vehicles. In addition, vehicles equipped with 7.5 litre engines will have insulation installed on engine compartment brake lines.
The throttle cable which runs from the accelerator to the governor assembly housing may have been kinked during assembly, causing excessive wear of the cable housing inner lining. This could result in either fracture or sticking of the cable.
Lower end of brake rod, which connects brake pedal arm to bell crank of power brake assebly, may have inadequate wall thickness.
These vehicles may not comply with c.M.V.S.S. 1103 - exhaust emissions. Vehicles may have fuel tank vapour hose that is too long and may be kinked near the connection to the evaporative emissions canister. Correction: Hoses will be inspected and length reduced if necessary.
Note: Vehicles equipped with 7.5 litre engines. These vehicles do not comply with c.M.V.S.S. 1103 - exhaust emissions. Incorrect egr valve. Correction: Egr valve will be replaced.
Quellen: NHTSA (USA, gemeinfrei), Transport Canada (Open Government Licence – Canada), DVSA (Vereinigtes Königreich, Open Government Licence v3.0), RappelConso und EU-Safety-Gate (Frankreich, Licence Ouverte 2.0), MLIT (Japan, Public Data License 1.0) und MOLIT (Südkorea, car.go.kr).