Frei lesbar · kostenloses Konto zum MitmachenNachfolger von Anticars (2000)

LexusLexus RX II

2003–2008 · 9 dokumentierte Mängel · 2 Märkte
Modelljahr
RückrufKritischElektrikNA

Elektrik

Problem: Dieser Rückruf betrifft bestimmte Blockheizsätze, die bei bestimmten Fahrzeugen installiert oder als Zubehör bei Toyota- oder Lexus-Händlern verkauft werden. Bei bestimmten Fahrzeugen hat das Motorblockheizkabel möglicherweise nicht ausreichend Hitzeschutz und kann durch hohe Temperaturen beschädigt werden. Wenn dies passiert, könnte das Kabel während des Einsteckens kurzschließen und dazu führen, dass die Kabel überhitzt oder schmelzen. Hinweis: Dieser Rückruf betrifft nur die folgenden Teilenummern des Blockheizer/-kabels: C014003034 PK5A408J09 PU14000904 C014003151 PK5A408J13 PU14000905 C014000885 PK5A489J11 PU14000907 C014000888 PK5A489J22 PU14000909 C014000907 PK5A410H00 PU14000911 C014100904 PU14000900 PU14000913 C014100907 PU14000901 PU14003571 C014100911 PU14000902 PK5A489J14 PK5A408J05 PU14000903 Sicherheitsrisiko: Überhitzung oder Schmelzen der Motorblockheizungsleitungen können ein Brandrisiko darstellen. Korrekturmaßnahmen: Toyota empfiehlt, die Motorblockheizung sofort nicht mehr zu verwenden. Toyota wird die Besitzer per Post benachrichtigen und Sie anweisen, Ihr Fahrzeug zu einem Händler zu bringen, um den Motorblockheizer zu deaktivieren. Für einige Fahrzeuge sind die Korrekturmaßnahmen für diesen Rückruf noch in Entwicklung. Bei anderen kann kein neuer Motorblockheizer installiert werden, und der Besitzer erhält eine Rückerstattung des Kaufpreises für den Motorblockheizer.

Transport Canada24. Nov. 20212021723Modelljahre 2007–2008Automatisch übersetzt · Original: EnglischDetails ansehen →
RückrufKritischBremsenEU

Motorrijtuigen en aanhangwagens - reminrichting

De gebruikte remvloeistof heeft onvoldoende smeereigenschappen. Hierdoor kan het achterste afsluitrubber van de hoofdremcilinder droog worden.

rdw18. Dez. 2013MGP100247Modelljahre 2003–2005Im Original (Niederländisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufKritischFahrwerkNA

Steering

On certain vehicles equipped with a 1MZ-FE or 3MZ-FE V6 engine, the crankshaft pulley may fail. The outer ring may become misaligned, or it may not properly rotate, causing noise and/or illumination of the discharge warning light. In addition, the power steering belt may become detached from the crankshaft pulley, which could result in a sudden increase in steering effort. A loss of steering power assist could result in a crash causing property damage and/or personal injury. Correction: Dealers will inspect and, if necessary, replace the crankshaft pulley.

Transport Canada9. Nov. 20112011397Modelljahre 2004–2006Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufKritischInnenraumNA

Seat belts:Rear/other

Certain sport utility vehicles fail to comply with the requirements of federal motor vehicle safety standard no. 210, "seat belt assembly anchorages." the anchor bolt for the rear, left-hand side seat belt buckle directly behind the driver's seat does not have sufficient strength.

NHTSA · USA27. Jan. 200606V023000Modelljahre 2004Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufMittelElektrikUK

Vehicle could suddenly stop

It is possible that due to variations in the build specification of the Intelligent Power Module (IPM) which includes the Insluted-Gate Bipolar Transistors (IGBT's) the lead-based solder could be affected by abnormally higher operating temperatures. This could result in a degrading of the solder and eventually heat damage to the IGBT's. If this occurs then warning lights on the instrument panel will illuminate. However if the driver fails to heed these warnings or the main power supply fuse blows then the vehicle could stop without warning.

DVSA · Vereinigtes Königreich16. Okt. 2013R/2013/104Modelljahre 2004–2007Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufMittelElektrikKR

각종 조작 스위치

하이브리드 시스템 인버터의 igbt(절연게이트 양극성 트랜지스터) 회로 과열로 계기판에 경고등이 점등되고 안전주행모드나 주행이 되지 않아 안전운행에 지장

MOLIT · Südkorea26. Sept. 20131398Modelljahre 2006–2008Im Original (Koreanisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufMittelElektrikEU

null In limited instances, the fuse of the power supply circuit for the Intelligent Power Module (IPM)…

null In limited instances, the fuse of the power supply circuit for the Intelligent Power Module (IPM) could blow, causing the hybrid system to shut down and resulting in the vehicle stopping while being driven, increasing the risk of a crash.

Safety Gate · EU6. Sept. 2013A12/1241/13Modelljahre 2005–2007Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufMittelMotorKR

엔진 본체 기계적 구성장치

엔진의 동력을 발전기와 파워핸들에 전달하는 풀리 불량으로 발전이 되지 않거나 핸들이 갑자기 무거워져 안전운행에 지장을 줄 가능성

MOLIT · Südkorea28. Nov. 2011875Modelljahre 2004–2005Im Original (Koreanisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufMittelElektrikUK

Vehicle may loose power

The Intelligent Power Module within the inverter system may fail. This will result in various warning lamps being illuminated. In most cases this will result in the vehicle entering the fail-safe mode resulting in limited power. In limited instances the fuse on the power supply circuit could blow resulting in the hybrid system stopping.

DVSA · Vereinigtes Königreich5. Aug. 2011R/2011/076Modelljahre 2004–2006Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufMittelElektrikKR

전기장치

자동차의 인버터(교류전력을 직류전력으로 변환해주는 장치) 불량으로 주행 중 하이브리드 기능이 상실되고 이 경우 출력이 제한(엔진 최고회전수 2,000rpm) 생산일자:`06.03.01, `06.08.01∼`06.08.09

MOLIT · Südkorea25. Juli 2011841Modelljahre 2006Im Original (Koreanisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufMittelElektrikNA

Electrical

On certain vehicles, a control board for the Intelligent Power Module (IPM), part of the hybrid system inverter assembly, could fail while the vehicle is underway. This could cause various warning lamps, including the malfunction indicator lamp, slip indicator lamp, brake system warning lamp, and master warning lamp, to illuminate on the instrument panel. If this occurred, in most cases, the vehicle would enter fail-safe driving mode, resulting in reduced motive power in which the vehicle could still be driven for short distances. In some instances, the fuse of the power supply circuit could blow, causing the hybrid system to stop functioning. The resultant loss of vehicle propulsion, in conjunction with traffic and road conditions, and the driver's reactions, could increase the risk of a crash causing property damage and/or personal injury. Correction: Dealers will inspect and, if necessary, replace the Intelligent Power Module.

Transport Canada29. Juni 20112011243Modelljahre 2006–2007Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufMittelMotorNA

Other

On certain vehicles, if the forward retention clip used to secure the floor carpet cover, which is located in front of the center console, is not installed properly, the cover may lean toward the accelerator pedal and interfere with the operation of the accelerator pedal arm. If this occurs, the accelerator pedal could temporarily become stuck in a partially depressed position, rather than return to the idle position. This could result in a loss of throttle control and a crash causing property damage and/or personal injury. Correction: Dealers will replace the floor carpet cover with a newly designed version. Note: This campaign also covers vehicles which may have been previously included in recall 2006168 (Toyota 609).

Transport Canada24. Feb. 20112011081Modelljahre 2004–2007Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufMittelSonstigesNA

Vehicle speed control:Accelerator pedal

Toyota is recalling certain model year 2004-2006 highlander, highlander hybrid, and model year 2004-2007 lexus rx330, rx350, and rx400h vehicles. If the forward retention clip used to secure the floor carpet cover, which is located in front of the center console, is not installed properly the cover may lean toward the accelerator pedal and interfere with the accelerator pedal arm.

NHTSA · USA24. Feb. 201111V112000Modelljahre 2004–2007Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufMittelBremsenUK

Brake master cylinder may fail.

If the incorrect brake fluid is used in the brake system it is possible that the rear seal can become dry and curl in its recess due to the operation of the piston. This can result in a brake fluid leak which will when the fluid reaches a low level illuminate the brake fluid low warning light on the dash.

DVSA · Vereinigtes Königreich8. Nov. 2010R/2010/170Modelljahre 2003–2005Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufMittelBremsenNA

Brakes

Certain vehicles use brake fluids containing polymers that act as lubricants for certain brake system components. If during vehicle maintenance, brake fluid is used that does not contain such polymers or only small amounts, part of the internal rubber seal located at the end of the brake master cylinder piston may become dry and may curl during movement of the piston. If this occurs, a small amount of the brake fluid could slowly leak from the brake master cylinder into the brake booster, resulting in illumination of the brake warning lamp. If the brake warning light has illuminated and the vehicle continues to be operated without refilling the master cylinder brake fluid reservoir, the driver will begin to notice a spongy or soft brake pedal feel and braking performance may gradually decline. This will increase the stopping distance, increasing the likelihood of a crash. Correction: Dealers will replace the brake master cylinder seal with a newly designed one.

Transport Canada21. Okt. 20102010361Modelljahre 2004–2006Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufMittelBremsenNA

Service brakes, hydraulic:Foundation components:Master cylinder

Toyota is recalling certain model year 2005-2006 avalon, model year 2004-2006 highlander, model year 2004-2006 lexus rx, and model year 2006 lexus gs and is vehicles. Brake fluid containing polymers is used that acts as lubricants for certain brake system components. If replacement brake fluid is used that does not contain such polymers, or that contains only small amounts, a part of the rubber seal located at the rear of the brake master cylinder may become dry, and the seal may curl during movement of the piston. If this occurs, a small amount of brake fluid could slowly leak from the seal into the brake booster.

NHTSA · USA21. Okt. 201010V499000Modelljahre 2004–2006Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufMittelInnenraumKR

승차 및 실내장치 기타

ㅇ 결함대상자동차 및 결함원인 - 렉서스RX330(1,863대):03.2.10~05.5.24에 제작수입된 자동차 - 운전석 오른쪽 하단에 바닥 카페트 고정하는 커버가 탈락하여 가속페달과 접촉될수 있음 ㅇ 결함시정 개시일 : 06.8.4 ㅇ 결함시정방법 : 무상수리 ※문의 : 한국토요타자동차(주) 고객센터(080-4300-4300)

MOLIT · Südkorea4. Aug. 2006326Modelljahre 2003–2005Im Original (Koreanisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufMittelSonstigesNA

Vehicle speed control:Accelerator pedal

On certain sport utility and hybrid vehicles, the two retaining clips for the driver's side forward center console can become loose. If both clips separate from the floor carpet cover, the cover may lean toward the accelerator pedal, causing interference with the accelerator pedal rod.

NHTSA · USA13. Juli 200606V253000Modelljahre 2004–2005Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufMittelSonstigesNA

Other

On certain vehicles, due to the improper installation of the retaining clips for the floor carpet cover located in front of the center console, there is a possibility that the clips may become loose. If both clips separate from the floor carpet cover, the cover may lean toward the accelerator pedal, causing interference with the accelerator pedal rod. In the worst case, the accelerator pedal may become stuck in a partially depressed position when returning to the idle position. Correction: Dealers will install new clips.

Transport Canada11. Juli 20062006168Modelljahre 2004–2006Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufMittelInnenraumNA

Seats And Restraints

Certain vehicles do not comply with the requirements of CMVSS 210. The left rear seat belt buckle anchor may separate from the floor before holding the required test load for the required time. If a separation occurred in a crash, the left rear seat occupant may not be properly restrained, increasing the risk of personal injury. Correction: Dealers will replace the left rear seat belt buckle anchor bolt.

Transport Canada26. Jan. 20062006021Modelljahre 2004Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufMittelElektrikUK

Possibility that the stop lamp could fail

In the stop lamp switch of subject vehicles equipped with LED stop lamps there is the possibility that silicone oxide may be generated the surface of the contact point and in consequence the resistance of the contact could increase. In this circumstance current may not flow causing the stop lamp to become inoperative.

DVSA · Vereinigtes Königreich15. Dez. 2004R/2004/199Modelljahre 2004Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufMittelBremsenKR

제동등

ㅇ 수입사 : (주)한국토요타자동차 ㅇ 결함대상자동차 및 대수 : 렉서스 RX330 1,222대 ㅇ 결함내용 : 제동등 스위치내의 접촉면에서 실리콘 산화물이 발생하여 접촉저항이 증가되어 제동등이 정상작동하지 않는 결함 ㅇ 대상자동차 : '02.10.16-'04.7.1까지 제작수입된 차량 ㅇ 결함시정기간 : '04.12.6-'06.6.5(1년6개월) ㅇ 결함시정방법 : 무상수리 ※ 문의 : 한국토요타자동차 고객지원센터 080-4300-4300

MOLIT · Südkorea6. Dez. 2004210Modelljahre 2003–2004Im Original (Koreanisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufMittelElektrikNA

Electrical

On certain vehicles equipped with a light emitting diode (LED) stop lamp, there is a possibility that silicon oxide may be generated on the surface of the contact point inside the stop lamp switch. Consequently, current may not flow at the contact, causing the stop lamp to become inoperative. The loss of stop lamps would result in failure to warn following drivers that the vehicle is braking and/or is stopped, which could lead to a vehicle crash. Correction: Dealers will replace the stop lamp switch.

Transport Canada23. Nov. 20042004409Modelljahre 2004Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Ältere →

Quellen: NHTSA (USA, gemeinfrei), Transport Canada (Open Government Licence – Canada), DVSA (Vereinigtes Königreich, Open Government Licence v3.0), RappelConso und EU-Safety-Gate (Frankreich, Licence Ouverte 2.0), MLIT (Japan, Public Data License 1.0) und MOLIT (Südkorea, car.go.kr).