Frei lesbar · kostenloses Konto zum MitmachenNachfolger von Anticars (2000)

Mazda Tribute

2000–2011 · 2 generationen · 19 dokumentierte Mängel · 4 Märkte
Generationen

Technische Bulletins (TSB) sind Reparaturanweisungen, die Hersteller ihren Händlern zu bekannten Problemen schicken. Sie sind keine Sicherheitsrückrufe, bestätigen aber oft einen Mangel.

Modelljahr
Tribute II · 2007–2011
BulletinKritischMotorNA

Bulletin

On some vehicles, a sulfur smell or 'rotten egg' odor may be noticed coming from the exhaust system. The odor is usually noticed after a cold start, fast idle, extended periods of idling and full throttle acceleration. Sulfur smell is not an indication of an engine concern and will not cause reduced driveability or durability of the engine or any of its emission components. The sulfur smell or 'rotten egg' odor is caused by high amounts of sulfur in the gasoline being used in the vehicle. Sulfur is normally eliminated during the refining process, but the EPA regulation of sulfur in gasoline differs from state to state. Vehicles using fuel containing high amounts of sulfur will most likely emit sulfur smell from the exhaust system.When high sulfur fuel is burned, there is a chemical reaction in the catalytic converter causing the sulfur tooxidize. As the vehicle is driven, the oxidizing reaction odor in the converter will decrease with mileage and age.

NHTSA · Herstellerbulletin10153311Modelljahre 2011Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Tribute II · 2007–2011
BulletinKritischMotorNA

Bulletin

On some vehicles, a sulfur smell or 'rotten egg' odor may be noticed coming from the exhaust system. The odor is usually noticed after a cold start, fast idle, extended periods of idling and full throttle acceleration. Sulfur smell is not an indication of an engine concern and will not cause reduced driveability or durability of the engine or any of its emission components. The sulfur smell or 'rotten egg' odor is caused by high amounts of sulfur in the gasoline being used in the vehicle. Sulfur is normally eliminated during the refining process, but the EPA regulation of sulfur in gasoline differs from state to state. Vehicles using fuel containing high amounts of sulfur will most likely emit sulfur smell from the exhaust system. When high sulfur fuel is burned, there is a chemical reaction in the catalytic converter causing the sulfur to oxidize. As the vehicle is driven, the oxidizing reaction odor in the converter will decrease with mileage and age.

NHTSA · Herstellerbulletin10145242Modelljahre 2011Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Tribute II · 2007–2011
BulletinMittelSonstigesNA

Bulletin

In Unterstützung der neuen MRT-Verteilung wird Mazda ab März 2019 ein neues Diagnosegerät zur Dual-Purpose-Lecksuche an die Händler ausliefern. Schulungsvideos werden in Kürze auf MGSS veröffentlicht, und die Verfahren im Werkstatthandbuch werden nach und nach überarbeitet.

NHTSA · Herstellerbulletin10154879Modelljahre 2011Automatisch übersetzt · Original: EnglischDetails ansehen →
Tribute II · 2007–2011
BulletinMittelFahrwerkNA

Bulletin

Wenn ein Fahrzeug während der Fahrt Karosserievibrationen oder Lenkradflattern aufweist und die Ursache als Reifenunwucht festgestellt wird, wuchten Sie die Reifen mit einer Hunter GSP9700 oder einer gleichwertigen Wuchtmaschine neu aus. Wenn Ihr Händler keine GSP9700 oder gleichwertige Wuchtmaschine hat, geben Sie das Fahrzeug zur Reparatur an eine Fremdwerkstatt weiter. Den Standort einer GSP9700 in der Nähe Ihres Händlers finden Sie auf der Website von Hunter unter www.gsp9700.com. Klicken Sie dort auf „Locate a GSP9700 Road Force Balancer“.

NHTSA · Herstellerbulletin10154139Modelljahre 2011Automatisch übersetzt · Original: EnglischDetails ansehen →
Tribute II · 2007–2011
BulletinMittelSonstigesNA

Bulletin

This service bulletin provides information regarding the proper use of the driver's floor mat to avoid anypotential interference with the foot pedals. The following are possible causes of floor mat interference,which can be avoided with proper usage. Floor mat moves forward due to improper installation. Inappropriate floor mat (such as aftermarket, non-factory-equipped, or non-genuine) is used. Floor mat is stacked one on top of another.

NHTSA · Herstellerbulletin10153331Modelljahre 2011Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Tribute II · 2007–2011
BulletinMittelFahrwerkNA

Bulletin

Some customers may complain that the steering wheel is off center more than 3 even when driving straight on a flat road.

NHTSA · Herstellerbulletin10153318Modelljahre 2011Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Tribute II · 2007–2011
BulletinMittelBremsenNA

Bulletin

Mazda North American Operations has approved an additional on-car brake lathe as an option for MNAO authorized equipment. The Pro-Cut On-Car Brake Lathe has been added to the MNAO authorized equipment program. NOTE: Accu-turn is still an approved brake lathe, but it is no longer available for purchase from our vendor. IMPORTANT: Rotors must be machined using a Mazda approved on-car brake lathe, or warranty claims are subject to denial or debit. Tool Number Description Pricing PC1923MAZ Pro-Cut On-Car Brake Lathe Check eStore or call for current pricing OBTAINING TOOLS This tool can be ordered through Mazda eStore. You can log on to eStore at: http://dealers.mazdausa.com CUSTOMER SERVICE INFORMATION For warranty or product information contact Mazda Authorized Service Equipment at 877-768-6657. Customer service representatives are available from 7:30 AM until 7:00 PM CST, Monday through Friday. SPECIAL SERVICE TOOL (SST) PART NAME: OVERVIEW Pro-Cut On-Car Brake Lathe PART NUMBER: PC1923MAZ APPLICABLE MODELS: All USAGE: To machine brake rotors on the vehicle.

NHTSA · Herstellerbulletin10153307Modelljahre 2011Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Tribute II · 2007–2011
BulletinMittelBremsenNA

Bulletin

Mazda North American Operations has approved an additional on-car brake lathe as an option for MNAO authorized equipment. The Pro-Cut On-Car Brake Lathe has been added to the MNAO authorized equipment program. NOTE: Accu-turn is still an approved brake lathe, but it is no longer available for purchase from our vendor. IMPORTANT: Rotors must be machined using a Mazda approved on-car brake lathe, or warranty claims are subject to denial or debit.

NHTSA · Herstellerbulletin10148003Modelljahre 2011Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Tribute II · 2007–2011
BulletinMittelBremsenNA

Bulletin

Mazda North American Operations has approved an additional on-car brake lathe as an option for MNAOauthorized equipment. The Pro-Cut On-Car Brake Lathe has been added to the MNAO authorizedequipment program.NOTE: Accu-turn is still an approved brake lathe, but it is no longer available for purchase from our vendor. IMPORTANT: Rotors must be machined using a Mazda approved on-car brake lathe, or warranty claimsare subject to denial or debit.

NHTSA · Herstellerbulletin10142515Modelljahre 2011Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Tribute II · 2007–2011
BulletinMittelFahrwerkNA

Bulletin

Some customers may complain that the steering wheel is off center more than 3 even when driving straight on a flat road.

NHTSA · Herstellerbulletin10142519Modelljahre 2011Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Tribute II · 2007–2011
BulletinMittelSonstigesNA

Bulletin

This service bulletin provides information regarding the proper use of the driver's floor mat to avoid any potential interference with the foot pedals. The following are possible causes of floor mat interference, which can be avoided with proper usage. Floor mat moves forward due to improper installation. Inappropriate floor mat (such as aftermarket, non-factory-equipped, or non-genuine) is used. Floor mat is stacked one on top of another. Use these points at your dealership to protect our mutual operations and to help ensure our customers' safety.

NHTSA · Herstellerbulletin10134703Modelljahre 2011Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Tribute II · 2007–2011
BulletinMittelKarosserieNA

Bulletin

When dealing with customer complaints of excessive condensation and/or water within the headlamp unit, first determine if all the bulb sockets (including O-ring), seals and covers are present and correctly installed. In most cases you will find that the Bulb Seal No. 1 (A) or HID Bulb Seal No. 1 (B) and Bulb Seal No. 2 (C) socket covers have not been correctly installed or are missing due to improper prior repairs (i.e., customer replacing the headlamp bulbs or body shop not transferring them when replacing the headlamp unit(s) due to a collision). Any damage caused by missing socket covers, HID module seal (D), or missing bumper brackets (E) is not covered by warranty policy.

NHTSA · Herstellerbulletin10118468Modelljahre 2011Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Tribute II · 2007–2011
BulletinMittelBremsenNA

Bulletin

Mazda Motor Corporation has decided to conduct a Special Service Program (SSP) on certain 2009-2011 Tribute vehicles. On certain 2009-2011 Tribute vehicles, contamination on the internal motor contacts of the throttle body may result in intermittent electrical connectivity.If this condition is present, the Malfunction Indicator Lamp or Wrench Lamp will illuminate, and the vehicle may enter fail-safe mode. In this mode, the engine power and vehicle speed is reduced, while maintaining full functionality of the power steering, power braking, lighting, and climate control systems. To improve vehicle performance should the above problem occur, dealers must reprogram the Powertrain Control Module (PCM). Please refer to Attachment II for repair details.This SSP will be in effect until July 31, 2015 regardless of mileage.

NHTSA · Herstellerbulletin10117770Modelljahre 2011Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Tribute II · 2007–2011
BulletinMittelBremsenNA

Bulletin

Mazda Motor Corporation is extending the warranty coverage for throttle body replacement on certain 2009-2011 Tribute vehicles produced from April 14, 2008 through May 30, 2011. The warranty for throttle body replacement will be extended to 10 years (120 months) from the original warranty start date or 150,000 miles, whichever comes first. If a vehicle has already exceeded the time or mileage limits, this coverage will last through January 31, 2015. Affected vehicles may develop contamination on the internal motor contacts of the throttle body, resulting in intermittent electrical connectivity. If this condition is present, the Malfunction Indicator Lamp (MIL) or Wrench light will illuminate and the vehicle may enter a fail-safe mode. In this mode, engine power and vehicle speed are reduced, while full functionality of the power steering, power braking, lighting, and climate control systems are maintained. If diagnosis identifies the throttle body as the causal component, dealers are authorized to replace the throttle body under this warranty extension program.This service must be performed at no charge to the vehicle owner.

NHTSA · Herstellerbulletin10117771Modelljahre 2011Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Tribute II · 2007–2011
BulletinMittelKarosserieNA

Bulletin

When dealing with customer complaints of excessive condensation and/or water within the headlamp unit, first determine if all the bulb sockets are resent and correctly installed. In most cases you will find that the bulb seal no. 1 (a) or hid bulb seal no. 1 (b) and bulb seal no. 2 (c) socket overs have not been correctly installed or are missing due to improper prior repairs (i.E., customer replacing the headlamp bulbs or body shop not transferring them when replacing the headlamp unit(s) due to a collision). Any damage caused by missing socket covers, hid module seal (d), or missing bumper brackets (e) is not covered by warranty policy.

NHTSA · Herstellerbulletin10105886Modelljahre 2011Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Tribute II · 2007–2011
BulletinMittelFahrwerkNA

Bulletin

Some customers may complain that the steering wheel is off center more than 3 even when driving straight on a flat road.

NHTSA · Herstellerbulletin10101062Modelljahre 2011Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Tribute II · 2007–2011
BulletinMittelKarosserieNA

Bulletin

When dealing with customer complaints of excessive condensation and/or water within the headlamp unit, first determine if all the bulb sockets are present and correctly installed. In most cases you will find that the bulb seal no. 1 (a) or hid bulb seal no. 1 (b) and bulb seal no. 2 (c) socket covers have not been correctly installed or are missing due to improper prior repairs (i.E., customer replacing the headlamp bulbs or body shop not transferring them when replacing the headlamp unit(s) due to a collision). Any damage caused by missing socket covers, hid module seal (d), or missing bumper brackets (e) is not covered by warranty policy.

NHTSA · Herstellerbulletin10098885Modelljahre 2011Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Tribute II · 2007–2011
BulletinMittelFahrwerkNA

Bulletin

Bulletin noteservice bulletin 06-001/14, 2008-2011 tribute - dtc b2278 stored in the power steering control module, is no longer valid. Service bulletin 06-001/14 has been superseded by safety recall 7614e, 2008-2011 tribute - electric power-assisted steering (epas).

NHTSA · Herstellerbulletin10098346Modelljahre 2011Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Tribute II · 2007–2011
BulletinMittelSonstigesNA

Bulletin

This service bulletin provides information regarding the proper use of the drivers floor mat to avoid any potential interference with the foot pedals. The following are possible causes of floor mat interference, which can be avoided with proper usage. Floor mat moves forward due to improper installation. Inappropriate floor mat (such as aftermarket, non-factory-equipped, or non-genuine) is used. Floor mat is stacked one on top of another.

NHTSA · Herstellerbulletin10098282Modelljahre 2011Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Tribute II · 2007–2011
BulletinMittelBremsenNA

Bulletin

Mazda north american operations received many requests from our dealers asking us to approve additional on-car brake lathes as an option for mnao authorized equipment. Due to your feedback and after evaluating a few on-car brake lathes, we are pleased to announce that we have added the pro cut on-car brake lathe to mnao authorized equipment program. The accu-turn is still an approved brake lathe but it is no longer available for purchase from our vendor. Important reminder rotors must be machined using a mazda approved on-car brake lathe or warranty claims are subject to denial or debit.

NHTSA · Herstellerbulletin10098245Modelljahre 2011Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Tribute II · 2007–2011
BulletinMittelSonstigesNA

Bulletin

Some vehicles may exhibit an intermittent no crank, no start condition with no diagnostic trouble codes (dtc) or passive anti-theft system (pats) indicator flashing.

NHTSA · Herstellerbulletin10097806Modelljahre 2010–2011Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Tribute II · 2007–2011
BulletinMittelGetriebeNA

Bulletin

Some vehicles equipped with an automatic transmission gain enhanced flat tow performance with an optional transmission cooling pump kit for recreational towing. The kit is available from the parts department and will help prevent transmission overheating.

NHTSA · Herstellerbulletin10097804Modelljahre 2011Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Tribute II · 2007–2011
BulletinMittelGetriebeNA

Bulletin

Some vehicles may exhibit an occasional fluid leak coming from the rear differential vent cap in temperatures below 32 degrees fahrenheit (0 degrees celsius) under certain conditions.

NHTSA · Herstellerbulletin10097801Modelljahre 2011Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Tribute II · 2007–2011
BulletinMittelFahrwerkNA

Bulletin

Some customers may complain that the steering wheel is off center more than 3 even when driving straight on a flat road.

NHTSA · Herstellerbulletin10097722Modelljahre 2011Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Tribute II · 2007–2011
BulletinMittelFahrwerkNA

Bulletin

Some customers may complain that the steering wheel is off center more than 3 even when driving straight on a flat road.

NHTSA · Herstellerbulletin10097377Modelljahre 2011Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Ältere →

Quellen: NHTSA (USA, gemeinfrei), Transport Canada (Open Government Licence – Canada), DVSA (Vereinigtes Königreich, Open Government Licence v3.0), RappelConso und EU-Safety-Gate (Frankreich, Licence Ouverte 2.0), MLIT (Japan, Public Data License 1.0) und MOLIT (Südkorea, car.go.kr).