Frei lesbar · kostenloses Konto zum MitmachenNachfolger von Anticars (2000)

Mazda Tribute

2000–2011 · 2 generationen · 19 dokumentierte Mängel · 4 Märkte
Generationen
Modelljahr
Tribute II · 2007–2011
RückrufKritischMotorNA

Kraftstoffsystem, Benzin:Förderung:Kraftstoffpumpe

Mazda North American Operations (Mazda) ruft bestimmte Fahrzeuge des Modelljahrs 2010–2011 der Baureihe Tribute zurück, die zwischen dem 3. März 2009 und dem 26. Mai 2011 gefertigt wurden. Bei Fahrzeugen mit 3,0-Liter-Motor kann das Kraftstofffördermodul (Fuel Delivery Module, FDM) reißen, was zu einem Kraftstoffaustritt führt.

NHTSA · USA28. Okt. 201616V788000Modelljahre 2010–2011Automatisch übersetzt · Original: EnglischDetails ansehen →
Tribute I · 2000–2011
RückrufKritischKarosserieNA

Structure:Frame and members

Mazda North American Operations (Mazda) is recalling certain model year 2001-2004 Tribute vehicles manufactured May 22, 2000, through December 19, 2003, originally sold, or currently registered in, Connecticut, Delaware, Illinois, Indiana, Iowa, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, West Virginia, Wisconsin and the District of Columbia. These vehicles may experience excessive corrosion at the forward attachment of the lower control arm.

NHTSA · USA4. Apr. 201414V174000Modelljahre 2001–2004Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Tribute I · 2000–2011Tribute II · 2007–2011
RückrufKritischMotorNA

Vehicle speed control:Cables

Mazda is recalling certain model year 2001 through 2006, and 2008, Tribute vehicles equipped with 3.0L V6 engines and speed control. Inadequate clearance between the engine cover and the speed control cable connector could result in a stuck throttle when the accelerator pedal is fully or almost-fully depressed. This risk exists regardless of whether or not speed control (cruise control) is used.

NHTSA · USA27. Juli 201212V357000Modelljahre 2001–2008Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Tribute I · 2000–2011
RückrufKritischBremsenNA

Brakes

Certain vehicles may have been originally equipped with a brake master cylinder reservoir cap that could leak. If brake fluid leaks from the cap, it could come in contact with the ABS module wiring harness connector. The same vehicles were previously involved in campaign 2007119 to address potentially missing or misplaced seals in the wiring harness connector to the ABS module electronic control unit. If this repair wasn’t done correctly, brake fluid leaking from the reservoir cap could corrode the ABS module electrical connector. This could result in vehicle fire causing property damage and/or personal injury. Correction: Dealers will replace the brake master cylinder reservoir cap and modify the ABS electrical system. Note: Owners are advised to park the vehicle outdoors until the remedy is applied.

Transport Canada21. Jan. 20122012020Modelljahre 2001–2002Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Tribute I · 2000–2011
RückrufKritischBremsenNA

Service brakes, hydraulic:Antilock/traction control/electronic limited slip:Control unit/module

Mazda is recalling certain model year 2001-2002 mazda tribute vehicles manufactured from april 20, 2000, through july 19, 2002. The brake master cylinder reservoir cap can leak brake fluid. If brake fluid leaks, it could come in contact with the antilock brake system (abs) module wiring harness connector.

NHTSA · USA20. Jan. 201212V016000Modelljahre 2001–2002Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Tribute I · 2000–2011
RückrufKritischBremsenNA

Service brakes, hydraulic:Antilock/traction control/electronic limited slip:Control unit/module

On certain sport utility vehicles equipped with antilock brakes (abs), the abs module connector may have missing or dislodged wire seals. This condition could allow contamination to enter the module connector, creating a potential for an electrical short.

NHTSA · USA10. Apr. 200707V157000Modelljahre 2001–2004Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Tribute I · 2000–2011
RückrufKritischBremsenJP

主ブレーキ一般

制動装置において、倍力装置の製造工程が不適切なため、ダイヤフラムが倍力装置の本 体容器に噛み込まれた状態のものがあり、そのままの状態で使用を続けると、ブレーキ操 作の繰り返しによりダイヤフラムが破損することがあり、負圧が漏れ、制動力が低下する おそれがある。

MLIT · Japan20. Dez. 20011107970Modelljahre 2001Im Original (Japanisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Tribute I · 2000–2011
RückrufKritischMotorNA

Fuel System

On certain vehicles, the o-ring seals in the fuel line connector at the fuel filter outlet may have been damaged during assembly. This damage can result in fuel odor or possible fuel leakage. Fuel leakage, in the presence of an ignition source, could result in a fire. Correction: Vehicles will be inspected and fuel line replaced if necessary.

Transport Canada2. Okt. 20002000212Modelljahre 2001Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Tribute I · 2000–2011
RückrufKritischMotorNA

Fuel system, gasoline:Delivery

Vehicle description: Sport utility vehicles. The o-ring seals in the fuel line connector at the outlet end of the fuel filter were damaged when the line was connected to the filter during vehicle assembly. In some cases, this damage could result in a fuel odor, or possibly in fuel dripping from the connection.

NHTSA · USA18. Sept. 200000V277002Modelljahre 2001Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Tribute I · 2000–2011
RückrufKritischFahrwerkNA

Wheels:Hubcap/cover

Vehicle description: Some 4x2 sport utility vehicles not equipped with an antilock braking system may have inadvertently been built with 4x4 rear hubs instead of 4x2 hubs. If the incorrect hubs are installed on a 4x2 vehicle, the rear wheels can loosen, or in some cases, separate from the vehicle.

NHTSA · USA12. Sept. 200000V260002Modelljahre 2001Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Tribute I · 2000–2011
RückrufKritischFahrwerkNA

Steering: Steering wheel/handle bar

Vehicle description: Sport utility vehicles. These vehicles may have a mis-assembled or incorrectly manufactured nut that attaches the steering wheel assembly to the steering column. The nut could be upside down in the steering wheel assembly, which could overstress the steering column shaft when the nut is tightened. In addition, some of the nuts may have been cracked during manufacture resulting in the nut fracturing when it is tightened during vehicle assembly.

NHTSA · USA9. Aug. 200000V223002Modelljahre 2001Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Tribute II · 2007–2011
RückrufMittelGetriebeNA

Antriebsstrang

Ein Sicherheitsmangel kann bei Fahrzeugen vorliegen, in denen als Ersatzteile für den Kundendienst generalüberholte Automatikgetriebe eingebaut wurden. Die Schalthebelschraube ist unter Umständen nicht mit dem vorgeschriebenen Anzugsdrehmoment festgezogen worden. Wenn sich die unzureichend angezogene Schalthebelschraube lockert und herausdreht, kann sich der Schalthebel ohne Vorwarnung vom Getriebe lösen, und das Getriebe reagiert möglicherweise nicht auf die Schaltbewegung des Fahrers. Dies könnte zum Verlust der Gangwahl im Getriebe und zu einer möglichen ungewollten Fahrzeugbewegung führen, wodurch das Risiko eines Unfalls mit Personen- und/oder Sachschäden steigt. Abhilfe: Händler überprüfen die Schaltbaugruppe und/oder die Schalthebelschraube und ersetzen sie bei Bedarf, wobei die Schraube mit dem vorgeschriebenen Drehmoment angezogen wird.

Transport Canada19. Okt. 20152015490Modelljahre 2008Automatisch übersetzt · Original: EnglischDetails ansehen →
Tribute II · 2007–2011
RückrufMittelGetriebeNA

Antriebsstrang:Automatikgetriebe:Schalthebel und Gestänge:Bodenschaltung

Mazda North American Operations (Mazda) ruft bestimmte Fahrzeuge des Modelljahres 2008 vom Typ Tribute zurück, die zwischen dem 9. Februar 2007 und dem 22. April 2008 gefertigt wurden. Bei den betroffenen Fahrzeugen wurde das Getriebe CD4E durch ein regeneriertes Getriebe ersetzt, das zwischen dem 11. Juni 2015 und dem 15. Juli 2015 instand gesetzt wurde. Bei diesen als Ersatzteil für Servicereparaturen eingesetzten Getrieben kann die Schraube des Schalthebels nicht ordnungsgemäß angezogen sein. Dadurch könnte sich hebel der Schaltsteuerung ohne Vorwarnung vom Getriebe lösen.

NHTSA · USA19. Okt. 201515V677000Modelljahre 2008Automatisch übersetzt · Original: EnglischDetails ansehen →
Tribute II · 2007–2011
RückrufMittelGetriebeNA

Hybrid propulsion system

Mazda North American Operations (Mazda) is recalling certain model year 2008 Mazda Tribute Hybrid vehicles manufactured October 10, 2006, to May 23, 2008. The coolant pump for the hybrid system may fail, resulting in the hybrid electronics overheating.

NHTSA · USA10. Sept. 201414V552000Modelljahre 2008Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Tribute II · 2007–2011
RückrufMittelFahrwerkNA

Steering:Electric power assist system

Mazda North American Operations (Mazda) is recalling certain model year 2008-2011 Tribute vehicles manufactured October 5, 2006, through September 11, 2010. The affected vehicles have a steering torque sensor that may not be able to properly detect driver steering input. As a result, the system could remove the Electric Power Steering (EPS) assist.

NHTSA · USA29. Mai 201414V282000Modelljahre 2008–2011Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Tribute I · 2000–2011
RückrufMittelMotorEU

null There may be inadequate clearance between the engine cover and the cruise control cable, which could…

null There may be inadequate clearance between the engine cover and the cruise control cable, which could allow the throttle to stick in the fully open position when the accelerator pedal is fully or almost-fully depressed. If this occurs, it would be difficult to stop or to decelerate, which could lead to an accident. This risk exists regardless of whether or not the cruise control is used.

Safety Gate · EU7. Nov. 2012A12/1697/12Modelljahre 2000–2004Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Tribute I · 2000–2011
RückrufMittelMotorUK

Possible unintentional increase of engine speed

The throttle valve may become stuck when the accelerator pedal is fully or almost fully depressed leading to possible unintentional increase of engine speed. This is caused by interference of the cruise control cable connector with the engine cover.

DVSA · Vereinigtes Königreich7. Nov. 2012R/2012/107Modelljahre 2001–2004Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Tribute I · 2000–2011
RückrufMittelFahrwerkJP

パワーステアリング

かじ取り装置のパワーステアリング用油圧ポンプのプーリー取り付けナットの締付け力及びプーリーの強度が不足しているため、当該プーリーの取り付けナットが緩む又はプーリーに亀裂が入るものがある。そのため、そのままの状態で使用を続けると、異音が発生し、最悪の場合、当該プーリーが破損又は外れてハンドル操作力が増大するおそれがある。

MLIT · Japan8. Juni 20062103200Modelljahre 2002–2005Im Original (Japanisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Tribute I · 2000–2011
RückrufMittelKarosserieNA

Visibility:Windshield wiper/washer:Motor

On certain trucks and sport utility vehicles, the windshield wiper motor may have been produced without grease applied to the output shaft gear.

NHTSA · USA17. Nov. 200505V525000Modelljahre 2006Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Tribute I · 2000–2011
RückrufMittelKarosserieNA

Latches/locks/linkages:Hatchback/liftgate:Lock

Certain 2004-2005 sport utility vehicles and certain 2001-2003 sport utility vehicle having rear liftgate components serviced with 2004 equivalent components fail to comply with the requirements of federal motor vehicle safety standard no. 206, 'door locks and door retention components.' the rear liftgate latching system does not meet the inertia load requirement in one direction.

NHTSA · USA23. Dez. 200404V605000Modelljahre 2001–2005Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Tribute I · 2000–2011
RückrufMittelMotorNA

Vehicle speed control:Cables

On certain sport utility vehicles, the accelerator cable may prevent the throttle from returning to the idle position.

NHTSA · USA10. Dez. 200404V583000Modelljahre 2002–2004Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Tribute II · 2007–2011
RückrufMittelInnenraumUK

Seat belt may not latch

It is possible that the driver and/or front seat passenger seat belt buckle cannot be latched or will not remain latched.

DVSA · Vereinigtes Königreich7. Mai 2004R/2004/002Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Tribute I · 2000–2011
Tribute I · 2000–2011
RückrufMittelInnenraumNA

Seat belts:Front:Buckle assembly

On certain sport utility vehicles, a post within the safety belt buckle covers could fracture, which could affect latch function, resulting in either a "no latch" or "partial latch" condition. In the "partial latch" condition, the buckle tongue can be inserted into the buckle and appear to be engaged, but will release from the buckle without the push button being depressed when a relatively low load is applied, such as when an occupant moves slightly in the seat.

NHTSA · USA15. Dez. 200303V515000Modelljahre 2001Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Tribute I · 2000–2011
RückrufMittelElektrikUK

Stop lamps may not work

Oil has remained on the stop lamp switch bracket during assembly. The oil deposit can cause the switch contacts to to carbonise. Due to this the stop lamp may not turn on even if the brake pedal is depressed.

DVSA · Vereinigtes Königreich13. Sept. 2002R/2002/118Modelljahre 2001–2002Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Ältere →

Quellen: NHTSA (USA, gemeinfrei), Transport Canada (Open Government Licence – Canada), DVSA (Vereinigtes Königreich, Open Government Licence v3.0), RappelConso und EU-Safety-Gate (Frankreich, Licence Ouverte 2.0), MLIT (Japan, Public Data License 1.0) und MOLIT (Südkorea, car.go.kr).