Frei lesbar · kostenloses Konto zum MitmachenNachfolger von Anticars (2000)

Mazda MX-5 (ND)

2015– · 7 dokumentierte Mängel · 4 Märkte

Technische Bulletins (TSB) sind Reparaturanweisungen, die Hersteller ihren Händlern zu bekannten Problemen schicken. Sie sind keine Sicherheitsrückrufe, bestätigen aber oft einen Mangel.

Modelljahr
BulletinKritischMotorNA

Bulletin

On some vehicles, a sulfur smell or 'rotten egg' odor may be noticed coming from the exhaust system. The odor is usually noticed after a cold start, fast idle, extended periods of idling and full throttle acceleration. Sulfur smell is not an indication of an engine concern and will not cause reduced driveability or durability of the engine or any of its emission components. The sulfur smell or 'rotten egg' odor is caused by high amounts of sulfur in the gasoline being used in the vehicle. Sulfur is normally eliminated during the refining process, but the EPA regulation of sulfur in gasoline differs from state to state. Vehicles using fuel containing high amounts of sulfur will most likely emit sulfur smell from the exhaust system.When high sulfur fuel is burned, there is a chemical reaction in the catalytic converter causing the sulfur tooxidize. As the vehicle is driven, the oxidizing reaction odor in the converter will decrease with mileage and age.

NHTSA · Herstellerbulletin10153311Modelljahre 2019Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelKarosserieNA

Bulletin

Dieses Bulletin ersetzt die zuvor unten aufgeführten Bulletins. Die Änderungen sind in Rot vermerkt. 09-012/21 13.12.21, 10.06.21 und 27.04.21 BESCHREIBUNG Einige Kunden können folgende Symptome erleben: Die Türverriegelung/Entriegelung funktioniert nicht mit dem Fernschalter des Senders. 1. Die Türverriegelung/Entschlussfunktion funktioniert nicht mit dem Tür- und Entriegelungssensor. 2. Der Motor startet nicht über den Zündschalter. 3. Der Sender arbeitet von selbst. 4. Die Schlüsselbatterie entlädt sich schneller als üblich. 5. Symptome 1-3: Dies kann durch übermäßige Last auf den Fernsender verursacht werden, die elektrische Anschlüsse verformen und einen schlechten Kontakt mit der Batterie schaffen. Um dieses Problem zu beseitigen, wurde die Struktur des Fernsender modifiziert, um die Verformung der elektrischen Anschlüsse zu verringern. Symptom 4-5: Dies kann entstehen, wenn übermäßige Last auf den Fernsender ausgeübt wird, wodurch eine Lücke um die Dichtung entsteht, in die Feuchtigkeit eindringt und die Platine korrodiert, wodurch die Schlüsselbatterie schneller als üblich entlädt wird. Um dieses Problem zu beseitigen, wurde die Dicke der Gehäusewand an der Dichtungsoberfläche erhöht und die Haftfestigkeit der Komponenten verbessert, um Verformungen zu verhindern. REPARATURVERFAHREN Wenn die Batterie defekt ist oder falsch installiert ist, ersetzen Sie die Batterie und/oder installieren Sie sie korrekt. Wenn die Fernbedienung der Energiesparfunktion ausgeschaltet ist und die Batterie korrekt eingebaut ist, ersetzen Sie den defekten Fernsender gemäß den Anweisungen auf MGSS (IMMOBILIZER SYSTEM-RELATED PARTS PROGRAMMING) durch einen modifizierten Sender. HINWEIS: Ersetzen Sie nicht andere Fernsender des Fahrzeugs, wenn keine Probleme auftreten.

NHTSA · Herstellerbulletin11034436Modelljahre 2020Automatisch übersetzt · Original: EnglischDetails ansehen →
BulletinMittelMotorNA

Bulletin

Some vehicles may exhibit oil leakage from the drive belt auto tensioner and rattling noises from the engine compartment. This may be caused by insufficient sealing at the drive belt auto tensioner damper when the auto tensioner fully operates under both high ambient temperature and high load conditions. To eliminate this concern, the shape of the drive belt auto tensioner damper has been changed.

NHTSA · Herstellerbulletin10238663Modelljahre 2019Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelFahrwerkNA

Bulletin

The Blind Spot Monitoring (BSM) system can malfunction with the following symptoms if the rear side radar sensors are installed facing the wrong direction. - BSM system indicates vehicle on the opposite side. - i-ACTIVSENSE indicator ring will not turn green - Rear Cross Traffic Alert (RCTA) does not work - Rear side radar sensor

NHTSA · Herstellerbulletin10222563Modelljahre 2023Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelBremsenNA

Bulletin

Some vehicles may experience a lack of power and the check engine light on with DTC P061B:00 stored in PCM memory under one of the following conditions (A or B). - DTC P061B:00 - [PCM] Internal control module torque calculation performance problem. Condition Condition Description A When cranking is interrupted (likely occurs when the brake pedal is released during cranking) B When accelerating from 1300-1600 rpm with wide open throttle Due to an improper control logic of the PCM, the engine torque calculation error detection is too sensitive. To eliminate this concern, the PCM software has been modified.

NHTSA · Herstellerbulletin10218722Modelljahre 2019Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelBremsenNA

Bulletin

Clunk/Rattle noise from rear brake

NHTSA · Herstellerbulletin10213396Modelljahre 2016Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelKarosserieNA

Bulletin

Some vehicles may experience one of the following 2 symptoms, even though the windshield is clear. Under certain driving conditions, the Forward Sensing Camera (FSC) may detect a dirty windshield (not clear). NOTE FOR CUSTOMER: The FSC may not work properly under the conditions: The windshield is not clear. The FSC lens is not clear. Driving in heavy rain, dense fog or snow, or into the sun. Driving on a road with no or blurred road lane markings. When the windshield becomes foggy in the winter time or other cold weather conditions and LDWS/HBC warning lights turn on, drive with the defroster on for about 10 minutes. This will help clear the foggy windshield at the FSC.

NHTSA · Herstellerbulletin10185957Modelljahre 2016Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelSonstigesNA

Bulletin

Some vehicles may exhibit the inner cloth (A) falling down at the rear end causing a poor appearance and obstructing the view of the back window. This is caused by the J-hook binding holding the inner cloth coming loose during the opening/closing of the convertible top, from vibration during driving or from high ambient temperatures. To correct the problem, two top-protector clips have been additionally installed to both side edges of the J-hook to prevent the J-hook from loosening and separating.

NHTSA · Herstellerbulletin10185955Modelljahre 2016Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelElektrikNA

Bulletin

Ldws and hbc warning lights on and dtc c1001:92

NHTSA · Herstellerbulletin10186337Modelljahre 2016Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelElektrikNA

Bulletin

If you experience issues with the current version of ID's such as missing tools or modules not showing after completing a network test, be advised that we are aware of these issues and are working to resolve them. As a counter measure, it is advised that you un-install ids and re-install version 103.00 and "do not update" until further notice.

NHTSA · Herstellerbulletin10185813Modelljahre 2017Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelMotorNA

Bulletin

If an engine assembly is replaced after a catastrophic internal mechanical failure, clean the intake manifold internally before installing a replacement engine assembly. If the intake manifold is not cleaned properly, the replacement engine may fail prematurely. Metallic debris from the old engine (with catastrophic internal mechanical failure) may rest inside the intake manifold. When the new engine assembly is installed, debris in the intake manifold will be ingested into the new engine and cause internal damage.

NHTSA · Herstellerbulletin10165676Modelljahre 2019Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelKarosserieNA

Bulletin

Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system.

NHTSA · Herstellerbulletin10165350Modelljahre 2019Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelSonstigesNA

Bulletin

Due to a database error discovered with IDS 114.00-114.02 release (which affects Recall 3719F), it will be necessary to uninstall IDS 114 and install IDS 113.00 and 113.06 update. The Recall can be performed after removing IDS 114 and installing IDS 113. This SA will be updated when more information is available.

NHTSA · Herstellerbulletin10163333Modelljahre 2019Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelSonstigesNA

Bulletin

On May 1, 2018, Japan produced vehicles starting using 17 mm hex lug nuts instead of 21 mm on the same size thread. When installing the accessory locking lug nuts, make sure to use the appropriate part number for the vehicle you are working on.

NHTSA · Herstellerbulletin10159199Modelljahre 2018–2019Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelFahrwerkNA

Bulletin

On May 1, 2018, Japan produced vehicles starting using 17 mm hex lug nuts instead of 21 mm on the same size thread. When installing new lug nuts or the accessory Wheel Lock Set, make sure to use the appropriate part number for the vehicle you are working on.

NHTSA · Herstellerbulletin10159196Modelljahre 2018–2019Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelSonstigesNA

Bulletin

In Unterstützung der neuen MRT-Verteilung wird Mazda ab März 2019 ein neues Diagnosegerät zur Dual-Purpose-Lecksuche an die Händler ausliefern. Schulungsvideos werden in Kürze auf MGSS veröffentlicht, und die Verfahren im Werkstatthandbuch werden nach und nach überarbeitet.

NHTSA · Herstellerbulletin10154879Modelljahre 2019Automatisch übersetzt · Original: EnglischDetails ansehen →
BulletinMittelFahrwerkNA

Bulletin

Subject: Mazda Service Program (MSP) 53. 2019 CX-3 & 2018-2019 MX-5 With Direct Tire Pressure Monitoring System (TPMS) Panic Alarm System Activates While Driving. Mazda Motor Corporation has decided to conduct a Mazda Service Program (MSP) on certain 2019 CX-3 vehicles produced from February 27, 2018 through October 12, 2018 and 2018-2019 MX-5 vehicles produced from October 3, 2017 through October 15, 2018. On certain subject vehicles equipped with Direct TPMS (TPMS wheel sensor is directly mounted on each wheel), it is possible that the panic alarm system may activate while driving, and the horn may sound intermittently, and hazard warning lights may flash. The panic alarm concern will stop after cycling the ignition switch off, then on again. No DTCs are stored. Action Required: Beginning today, reprogram the body control module (BCM) to the latest calibration using MMDS for all affected CX-3 and MX-5 vehicles in dealer inventory, and when customers bring their vehicles for maintenance, or other service/warranty work. The subject vehicles must not be delivered to customers until the repair of MSP53 is completed. Please inform the customer that the BCM will be reprogrammed to the latest calibration, free of charge. If a vehicle is sold with an open MSP53 your Step 3 PDI warranty claim will be subject to debit.

NHTSA · Herstellerbulletin10154528Modelljahre 2018–2019Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelFahrwerkNA

Bulletin

On certain subject vehicles, it is possible that the panic alarm system may activate while driving, and the horn may sound intermittently and hazard warning lights may flash. The panic alarm concern will stop after cycling the ignition switch off, then on again. No DTCs are stored. Some TPMS wheel sensor IDs on the concerned vehicle or other vehicles nearby may cause the error in the body control module (BCM). Air pressure data transmitted from the wheel sensors may be recognized by the BCM as if the panic button on the remote transmitter has been pressed.

NHTSA · Herstellerbulletin10154531Modelljahre 2018–2019Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelFahrwerkNA

Bulletin

Wenn ein Fahrzeug während der Fahrt Karosserievibrationen oder Lenkradflattern aufweist und die Ursache als Reifenunwucht festgestellt wird, wuchten Sie die Reifen mit einer Hunter GSP9700 oder einer gleichwertigen Wuchtmaschine neu aus. Wenn Ihr Händler keine GSP9700 oder gleichwertige Wuchtmaschine hat, geben Sie das Fahrzeug zur Reparatur an eine Fremdwerkstatt weiter. Den Standort einer GSP9700 in der Nähe Ihres Händlers finden Sie auf der Website von Hunter unter www.gsp9700.com. Klicken Sie dort auf „Locate a GSP9700 Road Force Balancer“.

NHTSA · Herstellerbulletin10154139Modelljahre 2019Automatisch übersetzt · Original: EnglischDetails ansehen →
BulletinMittelBremsenNA

Bulletin

Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.

NHTSA · Herstellerbulletin10153227Modelljahre 2019Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelInnenraumNA

Bulletin

This information is provided to help address Passenger Airbag Deactivation (PAD) Indicator illumination concerns during vehicle service.

NHTSA · Herstellerbulletin10153329Modelljahre 2019Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelSonstigesNA

Bulletin

This service bulletin provides information regarding the proper use of the driver's floor mat to avoid anypotential interference with the foot pedals. The following are possible causes of floor mat interference,which can be avoided with proper usage. Floor mat moves forward due to improper installation. Inappropriate floor mat (such as aftermarket, non-factory-equipped, or non-genuine) is used. Floor mat is stacked one on top of another.

NHTSA · Herstellerbulletin10153331Modelljahre 2019Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelFahrwerkNA

Bulletin

As of May 1, 2018, Japan produced vehicles use 17 mm hex lug nuts instead of 21 mm on the same size thread. When installing new lug nuts or the accessory Wheel Lock Set, make sure to use the appropriate part number for the vehicle you are working on. NOTE: The Mazda3 produced in Mexico is not affected.Use the GEPC or the Mazda Accessory web site [MXConnect (dealers.mazdausa.com)] to look up the correct part number for the vehicle you are working on.

NHTSA · Herstellerbulletin10153226Modelljahre 2018–2019Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelElektrikNA

Bulletin

Some vehicles may experience the CHECK ENGINE LIGHT ON with DTC P2610 and P2507 stored inmemory after engine start and room fuse 15A (A) removed. P2610:00: Instrument cluster internal engine off timer performance problem P2507:00: PCM battery voltage low input As a past malfunction, the customer will not notice it (no warning light illuminated), but the DTC may be found during a vehicle service. P2507 in this situation is only applicable on 2016 and later models. This is caused by the engine being started 3 or more times after a short duration of engine off (less than 15 seconds) with the room fused removed. NOTE: The odometer will display "F0-002" during transport mode (room fuse 15A removed). Transport mode is canceled when room fuse 15A is installed or the vehicle odometer is more than 12.4mi (20km). Vehicles in dealer inventory with this concern should be repaired using the following repair procedure.

NHTSA · Herstellerbulletin10153310Modelljahre 2019Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelFahrwerkNA

Bulletin

The vehicles listed above are equipped with a push button start/stop ignition system. Unlike previous Mazda models, there is no key cylinder on the steering column. Therefore, the engine cannot be started with the auxiliary key if the room fuse is removed or if the transmitter battery is dead.

NHTSA · Herstellerbulletin10153313Modelljahre 2019Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Ältere →

Quellen: NHTSA (USA, gemeinfrei), Transport Canada (Open Government Licence – Canada), DVSA (Vereinigtes Königreich, Open Government Licence v3.0), RappelConso und EU-Safety-Gate (Frankreich, Licence Ouverte 2.0), MLIT (Japan, Public Data License 1.0) und MOLIT (Südkorea, car.go.kr).