Frei lesbar · kostenloses Konto zum MitmachenNachfolger von Anticars (2000)

MercuryMercury Capri

1979–1994 · 2 generationen · 9 dokumentierte Mängel · 1 Märkte
Generationen
Modelljahr
MarktAlleNA
Capri II · 1979–1986
RückrufKritischInnenraumNA

Sitze und Rückhaltesysteme

Längere Sonneneinstrahlung kann dazu führen, dass die Kunststoffhülse der vorderen Gurtzungenbaugruppe, die den Sperrbolzen hält, spröde wird und sich verschiebt. Dadurch könnte sich die Gurtzunge vom Gurtband lösen, sodass der Sicherheitsgurt für den Fahrzeuginsassen unbrauchbar wird. Korrektur: Die Besitzer werden darüber informiert, dass Ford Sicherheitsgurte, bei denen dieser Zustand auftritt, reparieren wird.

Transport Canada28. Sept. 19921992117Modelljahre 1984–1985Automatisch übersetzt · Original: EnglischDetails ansehen →
Capri II · 1979–1986
RückrufKritischInnenraumNA

Seat belts:Front:Anchorage

The plastic sleeve in the front safety belt tongue assembly which retains the lock bar can deteriorate from prolonged exposure to sunlight and become displaced, causing the tongue to detach from the safety belt webbing.

NHTSA · USA29. Apr. 199292V063000Modelljahre 1984–1985Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Capri III · 1991–1994
RückrufMittelInnenraumNA

Air bags

The air bag modules do not meet the ford specifications for high ambient temperature performance.

NHTSA · USA2. Juni 199292V080000Modelljahre 1991–1992Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Capri II · 1979–1986
RückrufMittelInnenraumNA

Seats And Restraints

The forward screw which provides part of the attachment between the driver`s seat back assembly and the seat cushion frame could fracture and permit the driver's seat back to pivot rearward. Such a condition could adversely affect the driver's ability to control the vehicle and could result in a vehicle crash. Correction: New driver's seat cushion attachment screws will be installed on affected vehicles.

Transport Canada17. Mai 19881988066Modelljahre 1981–1983Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Capri II · 1979–1986
RückrufMittelInnenraumNA

Seat belts:Front:Anchorage

The bolts that attach the d-shaped ring for the shoulder belt are inadequately supported by the material in which they are mounted. The attachment does not comply with the requirements of federal motor vehicle safety standard no. 210, "seat belt assembly anchorages".

NHTSA · USA20. Dez. 198383V134000Modelljahre 1984Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Capri II · 1979–1986
RückrufMittelInnenraumNA

Rückruf

The upper torso restraint d-ring which attaches the shoulder belt to the b pillar, under certain test conditions, separated from its anchorage, and may not comply with cmvss 210 - belt anchorage.

Transport Canada17. Dez. 19831983114Modelljahre 1984Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Capri II · 1979–1986
RückrufMittelInnenraumNA

Rückruf

These vehicles do not comply with cmvss 209 - seat belt assemblies.

Transport Canada20. Dez. 19821982102Modelljahre 1980–1981Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Capri II · 1979–1986
RückrufMittelInnenraumNA

Seats:Front assembly:Recliner

The housing plates on the driver seat back latch recliner assemblies were manufactured with substandard material products. This tainted steel was used to produce seatback latches for both the right and left side seat assemblies. Under certain conditions, the defective housing plates may distort, allowing the locking teeth to disengage and tear off. This permits the seatback to pivot backwards.

NHTSA · USA8. Sept. 198181V102000Modelljahre 1981Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Capri II · 1979–1986
RückrufMittelInnenraumNA

Rückruf

Vehicles produced at dearborn assembly plant. Vehicles may have been equipped with driver seat back latch recliner assemblies that contain housing plates manufactured from suspect steel material. Under certain types of driver induced seat loading the recliner mechanism housing plates might distort allowing the locking teeth to disengage. This would allow the seat back to rotate rearward into a reclined position.

Transport Canada4. Sept. 19811981092Modelljahre 1981Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →

Quellen: NHTSA (USA, gemeinfrei), Transport Canada (Open Government Licence – Canada), DVSA (Vereinigtes Königreich, Open Government Licence v3.0), RappelConso und EU-Safety-Gate (Frankreich, Licence Ouverte 2.0), MLIT (Japan, Public Data License 1.0) und MOLIT (Südkorea, car.go.kr).