Vehicle speed control
On certain pickup trucks, passenger vehicles, sport utility vehicles, and motor homes chassis, the speed control deactivation switch may, under certain conditions, leak internally and then overheat, smoke, or burn.
🔔 Kostenloses Konto anlegen und Benachrichtigungen zu Mercury Capri (alle generationen) erhalten
On certain pickup trucks, passenger vehicles, sport utility vehicles, and motor homes chassis, the speed control deactivation switch may, under certain conditions, leak internally and then overheat, smoke, or burn.
The transmission fluid rubber tube connecting the transmission to the transmission oil cooler located in the radiator can become disconnected from the transmission, resulting in discharge of transmission fluid.
Längere Sonneneinstrahlung kann dazu führen, dass die Kunststoffhülse der vorderen Gurtzungenbaugruppe, die den Sperrbolzen hält, spröde wird und sich verschiebt. Dadurch könnte sich die Gurtzunge vom Gurtband lösen, sodass der Sicherheitsgurt für den Fahrzeuginsassen unbrauchbar wird. Korrektur: Die Besitzer werden darüber informiert, dass Ford Sicherheitsgurte, bei denen dieser Zustand auftritt, reparieren wird.
The plastic sleeve in the front safety belt tongue assembly which retains the lock bar can deteriorate from prolonged exposure to sunlight and become displaced, causing the tongue to detach from the safety belt webbing.
The rubber tube that connects the transmission to the transmission oil cooler (in the radiator) may disconnect causing discharge of fluid.
Bei Fahrzeugen mit EFI oder CFI kann sich die Federring-Schnellkupplung der Kraftstoffleitung, die die Kraftstoffzufuhr- und Rücklaufleitungen mit den EFI-Kraftstoffverteilern bzw. den CFI-Drosselklappengehäusen verbindet, sowie andere Kraftstoffleitungsanschlüsse nahe der Armaturenbrettverkleidung bei einigen Fahrzeugen während des Fahrzeugbetriebs lösen. Tritt dies auf, kommt es zu einem Kraftstoffverlust, wodurch die Gefahr eines Fahrzeugbrands besteht. Korrektur: Bei betroffenen Fahrzeugen werden Haltklammern für die Kupplungen installiert. Hinweis: Escort-Fahrzeuge sind mit EFI und CFI ausgestattet. Lynx-Fahrzeuge sind nur mit CFI ausgestattet. EFI – Elektronische Kraftstoffeinspritzung CFI – Zentrale Kraftstoffeinspritzung
The tandem power brake booster rear shells may have been produced with reduced wall thicknesses. Repeated brake applications could cau se such a shell to crack and the booster assembly to come apart.This could result in a total loss of braking capabilty without prior warn ing and present the possibility for loss of control and vehicle cras h.
The air bag modules do not meet the ford specifications for high ambient temperature performance.
The forward screw which provides part of the attachment between the driver`s seat back assembly and the seat cushion frame could fracture and permit the driver's seat back to pivot rearward. Such a condition could adversely affect the driver's ability to control the vehicle and could result in a vehicle crash. Correction: New driver's seat cushion attachment screws will be installed on affected vehicles.
Bremskraftverstärker-Rückschalen können verringerte Wandstärken aufweisen, wodurch die Schale brechen könnte. Folge des Mangels: Wiederholte Bremsbetätigung könnte dazu führen, dass die Schale reißt und sich die Verstärkereinheit auseinanderbaut. Die Betriebsbremsleistung würde ohne Vorwarnung vollständig ausfallen und könnte einen Unfall zur Folge haben.
Die sekundäre Drosselklappenwelle kann sich mit zunehmender Laufleistung verschmutzen und während der Fahrt in einer teilweise geöffneten Stellung festklemmen.
Carburetor throttle shafts may be susceptible to dirt contamination and wear of the bearing coatings. This could cause the secondary throttle plates to remain partially open after the driver has released the accelerator pedal. This this were to occur, engine speed would not return to idle potentially affecting vehicle control and stopping distances.
The bolts that attach the d-shaped ring for the shoulder belt are inadequately supported by the material in which they are mounted. The attachment does not comply with the requirements of federal motor vehicle safety standard no. 210, "seat belt assembly anchorages".
The upper torso restraint d-ring which attaches the shoulder belt to the b pillar, under certain test conditions, separated from its anchorage, and may not comply with cmvss 210 - belt anchorage.
Some of the vehciles affected by the recall may have been produced with incorrect hoods - the incorrect hoods were intended for use with conventional (non-turbo) engines and maynot provide a sufficient clearnace between the throttle linkage and the hood undersides. As a result, under certain conditions, the throttle linkage may come in contact with the hood potentially causing damage to the linkage and preventing the throttle from returning to its idle position.
Inadequate clearance between the underside of the hood and the throttle linkage could damage the linkage and prevent the throttle from returning to idle position. This condition is due to installation of the incorrect hood style during vehicle assembly.
These vehicles do not comply with cmvss 209 - seat belt assemblies.
The housing plates on the driver seat back latch recliner assemblies were manufactured with substandard material products. This tainted steel was used to produce seatback latches for both the right and left side seat assemblies. Under certain conditions, the defective housing plates may distort, allowing the locking teeth to disengage and tear off. This permits the seatback to pivot backwards.
Vehicles produced at dearborn assembly plant. Vehicles may have been equipped with driver seat back latch recliner assemblies that contain housing plates manufactured from suspect steel material. Under certain types of driver induced seat loading the recliner mechanism housing plates might distort allowing the locking teeth to disengage. This would allow the seat back to rotate rearward into a reclined position.
Vehicles equipped with turbocharged 2.3l engines and manual transmissions. Vehicles may have been built without a particular electric curcuit in the idle tracking system wiring harness. This condition may cause exhaust emissions of hydrocarbon (hc) and carbon monoxide (co) gases to exceed the limits specified by canada motor vehicle safety standard 1103 - exhaust emissions.
During the railcar chain-down operation or during in-transit railcar movement, the chain could interfere with and break the evaporative emission carbon canister. These vehicles would then not comply with canada motor vehicle safety standard 1105 - evaporative emissions.
Hinweis: Fahrzeuge mit 3,8-Liter-Motoren. Diese Fahrzeuge entsprechen möglicherweise nicht C.M.V.S.S. 1103 – Abgasemissionen. Das Trägermaterial in den Katalysatoren kann sich bei normalem Gebrauch lösen und zerbröseln, wodurch die Abgasemissionen den Grenzwert überschreiten können. Korrektur: Fahrzeuge werden überprüft, und der Katalysator wird bei Bedarf ersetzt.
Bestimmte 2.3-Liter-Mustang von 1987–89, 5.0-Liter-HO-Mustang und Capri von 1986 sowie 5.0-Liter-HO-Mustang und Mark VII von 1987–89. Diese Fahrzeuge entsprechen möglicherweise nicht der C.M.V.S.S. 1103 – Abgasemissionen. Das Trägermaterial im Katalysator kann sich im normalen Betrieb lösen und zerbröseln, wodurch die Abgasemissionen den Grenzwert überschreiten können. Korrektur: Der Katalysator wird bei Bedarf ersetzt.
Quellen: NHTSA (USA, gemeinfrei), Transport Canada (Open Government Licence – Canada), DVSA (Vereinigtes Königreich, Open Government Licence v3.0), RappelConso und EU-Safety-Gate (Frankreich, Licence Ouverte 2.0), MLIT (Japan, Public Data License 1.0) und MOLIT (Südkorea, car.go.kr).