Frei lesbar · kostenloses Konto zum MitmachenNachfolger von Anticars (2000)

Mini Mini

2001– · 5 generationen · 48 dokumentierte Mängel · 3 Märkte
Generationen

Technische Bulletins (TSB) sind Reparaturanweisungen, die Hersteller ihren Händlern zu bekannten Problemen schicken. Sie sind keine Sicherheitsrückrufe, bestätigen aber oft einen Mangel.

SchweregradAlleMittelGering
Modelljahr
Mini IV (F65/66/67) · 2024–
BulletinMittelElektrikNA

Bulletin

Aufgrund eines Implementierungsfehlers in verschiedenen OBD-Diagnosefunktionen der Steuergeräte des Fahrzeugs kann es in sehr seltenen Fällen vorkommen, dass gespeicherte Fehlerspeichercodes (DTCs) und die MIL (Warnleuchte) nicht automatisch gelöscht werden, obwohl die zugrunde liegende Störung bereits behoben wurde. Dies entspricht nicht den gesetzlichen OBD-Vorgaben.

NHTSA · Herstellerbulletin11034470Modelljahre 2025Automatisch übersetzt · Original: EnglischDetails ansehen →
Mini IV (F65/66/67) · 2024–
BulletinMittelElektrikNA

Bulletin

Aufgrund eines Implementierungsfehlers in verschiedenen OBD-Diagnosefunktionen der Steuergeräte des Fahrzeugs kann es in sehr seltenen Fällen vorkommen, dass gespeicherte Fehlerspeichercodes (DTCs) und die MIL (Warnleuchte) nicht automatisch gelöscht werden, obwohl die zugrunde liegende Störung bereits behoben wurde. Dies entspricht nicht den gesetzlichen OBD-Vorgaben.

NHTSA · Herstellerbulletin11031579Modelljahre 2025Automatisch übersetzt · Original: EnglischDetails ansehen →
Mini III · 2013–2024
BulletinMittelElektrikNA

Bulletin

Die richtige Batteriepflege ist unerlässlich, wenn MINI-Fahrzeuge in Ihrem Center auf Lager stehen. Lässt man die Niederspannungsbatterie eines Fahrzeugs unter 12,0 Volt (12,0 V) absinken, verkürzt sich die zu erwartende Batterielebensdauer dauerhaft, und es kann zu einem vorzeitigen Ausfall kommen. Bei Fahrzeugen mit Hochvolt-Batterie (HV) (Plug-in-Hybrid Electric Vehicle (PHEV) und Battery Electric Vehicle (BEV)) kann eine unsachgemäße Wartung oder Handhabung dazu führen, dass die HV-Batterie entladen wird und ausgetauscht werden muss. Wir stellen ein flexibles Batteriepflegesystem zur Verfügung, das jeder MINI-Händler an seine jeweiligen Bedürfnisse anpassen kann. Dieses Bulletin erläutert den Batterie-Ladekalender (siehe Anhang), das Ladesystem und das unten beschriebene Verfahren zur Überprüfung der Batteriespannung.

NHTSA · Herstellerbulletin10245427Modelljahre 2024Automatisch übersetzt · Original: EnglischDetails ansehen →
Mini II · 2006–2013
BulletinMittelElektrikNA

Bulletin

N12 Tankleck-Diagnosemodul (DMTL) Pumpe: begrenzte Garantieverlängerung auf 10 Jahre/120.000 Meilen

NHTSA · Herstellerbulletin10216756Modelljahre 2009Automatisch übersetzt · Original: EnglischDetails ansehen →
Mini III · 2013–2024
BulletinMittelElektrikNA

Bulletin

CONDENSATION FROM AIR CONDITIONING LEAKS INTO PASSENGER FOOTWELL: Condensation from the air conditioning systems evaporator drips, below the instrument panel, into the passenger's footwell. During assembly, the cover of the fresh air intake was not fully seated when the screws were tightened. This cover can then leak condensation out through the existing gap.

NHTSA · Herstellerbulletin10182928Modelljahre 2021Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Mini III · 2013–2024
BulletinMittelElektrikNA

Bulletin

CONDENSATION FROM AIR CONDITIONING LEAKS INTO PASSENGER FOOTWELL: Condensation from the air conditioning systems evaporator drips, below the instrument panel, into the passenger's footwell. During assembly, the cover of the fresh air intake was not fully seated when the screws were tightened. This cover can then leak condensation out through the existing gap.

NHTSA · Herstellerbulletin10182629Modelljahre 2021Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Mini II · 2006–2013
BulletinMittelElektrikNA

Bulletin

CLASS ACTION SETTLEMENT: N14 HIGH-PRESSURE FUEL PUMP (HDP) SERVICE BENEFIT CLASS VEHICLES: The MINI vehicle may experience a sudden engine operational failure reduced or loss of power while driving and the malfunction indicator lamp (MIL) may be illuminated along with high-pressure fuel pumprelated faults stored in the Engine Control Module (DME). PROCEDURE Perform the corresponding diagnosis/vehicle test and run the test plans to completion as applicable.

NHTSA · Herstellerbulletin10171506Modelljahre 2009Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Mini III · 2013–2024
BulletinMittelElektrikNA

Bulletin

"Air Conditioning Refrigerant R1234yf Introduction. INFORMATION Highlights of R-1234yf Meets SAE J2888_201301 ""This SAE Standard covers fittings, couplers, and hoses intended for connecting service hoses from mobile air- conditioning Systems to service equipment such as charging, recovery and recycling equipment"". New tools and equipment are required. To service vehicles equipped with R-1234yf refer to SI M04 01 16. Air conditioning technician certification is required to work on system. Refer to your State Law. Unique low and high side fittings. Revised evaporator core as per SAE J2842. System will use about 5% more refrigerant than a comparable R134a system. System oil is a specific PAG oil. Refer to ISTA repair recommendation. Do not interchange components between systems using other refrigerants. Do not reuse Seals / O-ring material from another system. The system piping has internal heat exchangers (IHX or IWT). SAFETY INFORMATION Several precautions need to be observed when working on automotive air conditioning systems: Always wear eye protection and gloves while handling refrigerant or servicing air conditioning system. Avoid breathing R1234yf lubricant vapor or mist. Use only approved service equipment to discharge A/C systems. If refrigerant or compressor oil contacts the skin or eyes, large quantities of cool water should be used to flush the affected area. Never heat a refrigerant container with an open flame. Keep all refrigerant away from open flames. Under no circumstances should R1234yf service equipment or vehicle A/C systems be pressure tested or leak tested with air/R1234yf mixtures. NOTE: The use of compressed air (shop air) for leak detection in an R1234yf system can contaminate the system and/or refrigerant with moisture. Leak detection equipment that meets the SAE J2791 standard will work with R1234yf Never use fittings for an R12 or R134a system on an R1234yf system. Any difficulty in connecting service equipment may be an indication of ref

NHTSA · Herstellerbulletin10151231Modelljahre 2016Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Mini II · 2006–2013
BulletinMittelElektrikNA

Bulletin

"N12 Tank Leak Diagnostic Module (DMTL) Pump: Limited Warranty Extension to 10 Years/120,000 Miles. INFORMATION This updated version of this bulletin now includes the addition of the model year 2009 R55, R56 and R57 MINI Cooper vehicles with the N12 engine. For the above-referenced vehicles, MINI USA, a division of BMW of North America, LLC (""MINI USA"") is extending the limited warranty for the Tank Leak Diagnostic Module (DMTL) Pump to: 10 years/120,000 miles as determined by the vehicle's original in-service date Component #1: This ""component specific"" limited warranty extension applies to defects in materials and workmanship and is subject to the applicable vehicle and coverage eligibility requirements, exclusions and limitations that apply to the MINI New Passenger Car Limited Warranty. GRUSB0116-04 This bulletin is notice of a ""limited warranty extension."" This is NOT a notice of a Recall or Service Action. There is no immediate repair required unless the MINI vehicle is currently experiencing this problem. Even though this is NOT a Recall, MINI USA will be sending VIN-specific customer notification letters in a phased release. Customer Notification Letter - VIN and Component-specific Warranty Extension Even though this is NOT a Recall, MINI USA will be sending VIN-specific customer notification letters in a phased release for the additional MY 2009 vehicles."

NHTSA · Herstellerbulletin10151222Modelljahre 2009Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Mini III · 2013–2024
BulletinMittelElektrikNA

Bulletin

"SI M84 02 15 Communication Systems SUBJECT HU-B: Bluetooth Connection Fails Sporadically . Page 1 of 2 January 2016 Technical Service The Bluetooth system works intermittently. One or more of the following scenarios may occur: ? Bluetooth pairing is not possible - display shows ""Please wait"" ? Unable to select the check box to activate Bluetooth? Device does not reconnect to the vehicle after a key cycle ? Audio interference noise is heard listening to iPod etc. ? When trying to access the user manual, the display shows ""Please wait"" Incorrect software installed in the Radio MINI Visual Boost."

NHTSA · Herstellerbulletin10151050Modelljahre 2016Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Mini III · 2013–2024
BulletinMittelElektrikNA

Bulletin

B38 and B48 Engines: Engine Oil Pressure Faults Stored in DME Memory. INFORMATION When diagnosing the vehicle, the following fault is stored in the DME: FC 1C0102 Engine Oil Pressure control, plausibility, static: pressure too low If the vehicle's integration level is not F056-14-11-500 or higher, and no other faults related to the engine oil pump or engine oil pressure regulating valve are stored in the DME, it can be ignored. This fault will not illuminate the Service Engine Soon lamp. When available, the vehicle can be reprogrammed to integration level F056-14-11-500 or higher to eliminate this erroneous fault. The release of this integration level is scheduled for December 2014. This bulletin will be updated when the applicable programming software is available. If one of the following faults is stored in the DME memory in conjunction with the fault above, or the oil pressure warning lamp is illuminated, proceed with diagnosing the vehicle with the applicable test plan for the fault stored. FC 1C2002 Oil pump, mechanical: Oil pressure too low And/or FC 1C0301 Oil pressure regulating valve, mechanical: hangs in a fully energized position (minimum oil pressure WARRANTY INFORMATION Not applicable.

NHTSA · Herstellerbulletin10148345Modelljahre 2014Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Mini II · 2006–2013
BulletinMittelElektrikNA

Bulletin

N16: Fault 274D Mixture Adaptation Is Stored in the DME. Certain low speed, light-load driving conditions at lower outside temperatures could cause the Service Engine Soon lamp (MIL) to illuminate. The following fault would be stored in the DME: Fault 274D: Mixture adaptation, lower engine speed range (mixture too lean) CAUSE 1. Possible intake/exhaust leaks, or a faulty component as listed in the test plan 2. Unfavorable DME software

NHTSA · Herstellerbulletin10148346Modelljahre 2009–2012Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Mini III · 2013–2024
BulletinMittelElektrikNA

Bulletin

"Delivery Stop/Service Action:Replace Oil Filter Housing Assembly. A Delivery Stop has been issued on certain 2014 model year F56 vehicles produced from November 2013 to March 2014. A coolant leak could occur at the oil filter housing, resulting in overheating, loss of power and an engine warning light. Affected vehicles in dealer inventory must not be retailed or delivered until the oil filter assembly has been replaced. Vehicles at ports of entry will be repaired prior to dealer delivery. The affected vehicles are listed in the attachment to this bulletin; they are also identified with a ""Vehicle Comment"" in the DCSnet Warranty Vehicle Inquiry or ISPA, as follows: Defect Code 0011330300, Delivery Stop, Oil Cooler; see SI M11 01 14."

NHTSA · Herstellerbulletin10148294Modelljahre 2014Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Mini II · 2006–2013
BulletinMittelElektrikNA

Bulletin

Service Action: Bluetooth Software (KISU Data) Update. This Service Action is being released to improve customer satisfaction as we strive to be number 1 in the JD Power Initial Quality Survey (IQS). This new KISU software improves the Bluetooth functionality in our vehicles, and it helps to keep us up-to-date with technology innovation. Please implement the Bluetooth Software Update Service Action. This Service Action will be in effect until March 2015. Thank you for your continuous support. Improved KISU data (Customer Initiated Software Update) is now available for installation in these vehicles via the USB port. Improved functionality for COMBOX: z Detailed view of the text messages z Android device connection stability (linked contacts causing BT disconnection) Improved functionality for HU-H: z Reconnection strategy z 3rd Party App Metadata - Album art and song title Note: This Service Action is to be completed only at the dealer. You (dealers) will be receiving vehicles from the VDCs that will require this Service Action to be completed prior to customer delivery.

NHTSA · Herstellerbulletin10148212Modelljahre 2009Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Mini III · 2013–2024
BulletinMittelElektrikNA

Bulletin

Service Action: Replace Oil Filter Housing Assembly. A coolant leak could occur at the oil filter housing, resulting in overheating, loss of power and an engine warning light.

NHTSA · Herstellerbulletin10148202Modelljahre 2014Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Mini II · 2006–2013
BulletinMittelElektrikNA

Bulletin

"N16 and N18 Engine Oil Leak. The customer states that a small engine oil leak can be seen from the underside of the engine. CAUSE The internal sealing of the oil pump volume control solenoid valve is compromised, allowing engine oil to leak from the oil pump volume control solenoid. DIAGNOSTIC Below is the procedure for identifying how far the engine oil has migrated inside the engine electrical harness, when this issue occurs, if at all. The procedure must be followed very carefully so that the proper repair is identified. 1. Disconnect the oil pump volume control solenoid valve electrical connection per Repair Instructions 11 41 519 ""Removing and installing or replacing the solenoid valve (engine oil pump)."" Inspect the electrical connector; if no engine oil is found inside the electrical connector, perform the oil pump volume control valve repair procedure. If engine oil is found inside the electrical connector, proceed to diagnostic procedure step 2. 2. Remove the cover from the DME and remove all three electrical connectors from the DME. Inspect the connectors for traces of engine oil. If no engine oil is found, perform the oil pump volume control valve repair procedure and replace the engine section of the wire harness. Refer to EPC for the additional part number. If engine oil is found in the DME connector, proceed to step 3. 3. If engine oil is found in the DME electrical connector, perform the oil pump volume control valve repair procedure, replace the engine section of the wire harness and replace the DME. Refer to EPC for the additional part numbers. Do not remove the engine oil pan. Do not replace the oil pump volume control valve. Do not replace engine oil pump. OIL PUMP VOLUME CONTROL VALVE REPAIR"

NHTSA · Herstellerbulletin10147956Modelljahre 2009Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Mini II · 2006–2013
BulletinMittelElektrikNA

Bulletin

N16: Fault 274D Mixture Adaptation Is Stored in the DME. Certain low speed, light-load driving conditions at lower outside temperatures could cause the Service Engine Soon lamp (MIL) to illuminate. The following fault would be stored in the DME: ??Fault 274D: Mixture adaptation, lower engine speed range (mixture too lean) CAUSE 1. Possible intake/exhaust leaks, or a faulty component as listed in the test plan 2. Unfavorable DME software.

NHTSA · Herstellerbulletin10147958Modelljahre 2009–2012Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Mini III · 2013–2024
BulletinMittelElektrikNA

Bulletin

"Engine Cranks, No Start and/or Engine Coolant Temperature Faults. 1 The engine either exhibits a crank, no start or a hard start (long crank), usually on a cold engine. No faults are stored in the DME. Proceed to Correction 1 for further diagnosis. 2 NOTE: The engine may also exhibit the same starting behavior as in Situation1. The Service Engine Soon lamp is illuminated, with one or more of the following fault codes stored in the DME: Engine temperature sensor faults ? 2943 Coolant temperature sensor, signal change too fast ? 2937 Coolant temperature sensor, electrical: short circuit to positive ? 2936 Coolant temperature sensor, electrical: short circuit to earth ? 293A Coolant temperature sensor, plausibility, cold start: temperature too high ? 293B Coolant-temperature sensor, plausibility, cold start: Temperature too low ? 2947 Coolant-temperature sensor, signal: Fixed on low ? 2948 Coolant-temperature sensor, signal: Fixed ? 3393 Engine downtime, plausibility: Time too long in correlation with engine coolant cooling down ? 3392 Engine downtime, plausibility: Time too short in correlation with engine coolant cooling downIf any of the above fault codes are stored, proceed to Correction 2. Engine thermostat faults: ? 348E Characteristic map thermostat, actuation: Short circuit to positive ? 348F Characteristic map thermostat, actuation: Short circuit to earth ? 3490 Characteristic map thermostat, actuation: Open circuit If any of the above fault codes are stored then proceed to Correction 2: The above fault codes for the engine temperature sensor and thermostat are the primary fault codes for turning the Service Engine Soon light on. 1. Poor solder contacts in the engine coolant temperature sensor integrated into the engine thermostat housing 2. A faulty external or replaceable engine coolant temperature sensor (see below for identifying production changes in the thermostat and engine temperature sensors) 3. A faulty map-contro

NHTSA · Herstellerbulletin10147700Modelljahre 2013Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Mini III · 2013–2024
BulletinMittelElektrikNA

Bulletin

"THERMOSTAT FAULTS (B-ENGINES). The Service Engine Soon light is on. A Check Control message for ""Engine overheated"" and or ""Exercise caution!"" may also display. The following fault codes may be stored in the DME: 1D2401 - Characteristic map thermostat, actuation: Short circuit to B+ 1D2402 - Characteristic map thermostat, actuation: Short circuit to ground 1D2404 - Characteristic map thermostat, actuation: Line disconnection During diagnosis the coolant may be found to be discolored. Insulation on the wiring for the map activation thermostat (heating element) may be damaged. Exposed wiring may allow coolant to enter the harness. This may cause damage to the heating element."

NHTSA · Herstellerbulletin10147576Modelljahre 2016Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Mini III · 2013–2024
BulletinMittelElektrikNA

Bulletin

"B46 LEAK DIAGNOSIS MODULE (NVLD): LIMITED WARRANTY EXTENSION TO 10 YEARS/120,000 MILES FOR ""NON-CALIFORNIA EMISSION"" STATUTE STATES. INFORMATION For the eligible vehicles that are not eligible for coverage under the ""State of California PZEV (SULEV) emission regulation,"" MINI USA a division of BMW of North America, LLC (""MINI USA"") is extending the limited warranty for the leak diagnosis module (NVLD) to: 10 years/120,000 miles as determined by the vehicle's original in-service date Item #1: This componentspecific limited warranty extension applies to defects in materials or workmanship. This coverage is subject to the same vehicle eligibility requirements, limitations, and exclusions that apply to the MINI New Passenger Car Limited Warranty.Note: This bulletin is notice of a ""limited warranty extension."" This is NOT a notice of a Recall or Service Action. There is no immediate repair required unless the MINI vehicle is currently experiencing this problem. Customer Notification Letter - VIN and Component-specific Warranty Extension Even though this is NOT a Recall, MINI USA will be sending VIN-specific customer notification letters in a phased release. ELIGIBLE VEHICLES To assist you in identifying the ""eligible vehicles"" that have this extended limited warranty coverage, the DCSnet Warranty Vehicle Inquiry will be updated with the VIN-specific ""Vehicle Comment"" shown below: MINI USA has extended the limited warranty for the leak diagnosis module (NVLD) on this vehicle to 10 years/120,000 miles as determined from the original in-service date. This component-specific limited warranty extension applies to defects in materials or workmanship. This coverage is subject to the same vehicle eligibility requirements, limitations, and exclusions that apply to the MINI New Passenger Car Limited Warranty. See SI M01 04 16. Vehicles that are registered in California or a State that has ""fully"" adopted the ""State of California PZEV (SULEV) emission regulation.""

NHTSA · Herstellerbulletin10147572Modelljahre 2015Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Mini II · 2006–2013
BulletinMittelElektrikNA

Bulletin

FOOTWELL MODULE: LIMITED WARRANTY EXTENSION TO 8 YEARS/125,000 MILES. When performing ISTA/D diagnosis and/or a programming procedure (software update) on an affected vehicle, the Footwell Module could fail. There is a compatibility issue with certain combinations vehicle software (Plant Integration ILevel) and the Footwell Module hardware installed in the vehicle.

NHTSA · Herstellerbulletin10147573Modelljahre 2011Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Mini III · 2013–2024
BulletinMittelElektrikNA

Bulletin

"B38 AND B48 LEAK DIAGNOSIS MODULE (NVLD): LIMITED WARRANTY EXTENSION TO 10 YEARS/120,000 MILES. INFORMATION For the eligible vehicles, MINI USA a division of BMW of North America, LLC (""MINI USA"") is extending the limited warranty for the leak diagnosis module (NVLD) to: 10 years/120,000 miles as determined by the vehicle's original in-service date Note: This bulletin is notice of a ""limited warranty extension."" This is NOT a notice of a Recall or Service Action. There is no immediate repair required unless the MINI vehicle is currently experiencing this problem. Customer Notification Letter - VIN and Component-specific Warranty Extension Even though this is NOT a Recall, MINI USA will be sending VIN-specific customer notification letters in a phased release. ELIGIBLE VEHICLES To assist you in identifying the ""eligible vehicles"" that have this extended limited warranty coverage, the DCSnet Warranty Vehicle Inquiry will be updated with the VIN-specific ""Vehicle Comment"" shown below: MINI USA has extended the limited warranty for the leak diagnosis module (NVLD) on this vehicle to 10 years/120,000 miles as determined from the original in-service date. This component-specific limited warranty extension applies to defects in materials or workmanship. This coverage is subject to the same vehicle eligibility requirements, limitations, and exclusions that apply to the MINI New Passenger Car Limited Warranty. Please see SI M01 03 16. Warning: Before performing and submitting a repair under this extended limited warranty (ELW), always do a DCSnet Warranty inquiry to confirm that the vehicle has the above ""Notice of Limited Warranty Extension"" in the Vehicle Comment section. The ""model year"" production start (SOP) and end date (EOP) for a specific ""model variant"" within a ""Series"" will vary, please do not use a vehicle's production date as the sole determent for ELW coverage eligibility. If you have ELW eligibility and/or coverage question, please send an ema

NHTSA · Herstellerbulletin10147064Modelljahre 2014–2015Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Mini III · 2013–2024
BulletinMittelElektrikNA

Bulletin

"MIL LIGHT WITH DME FAULTS 1B2002 AND 1F1A51 STORED. Service Engine Soon (MIL) light is on. Both of the following fault codes are stored in Digital Motor Electronics (DME) memory: 1B2002: ""EWS protection against tampering: no starting value programmed"" 1F1A51: ""DME, internal fault: Read EEPROM faulty"" Note: Only vehicles with DME MEVD17.2.3 produced or programmed to Integration level 16-03-50x - 16-07-50x - 16-11-50x are affected. Ineffective DME software."

NHTSA · Herstellerbulletin10146868Modelljahre 2016Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Mini III · 2013–2024
BulletinMittelElektrikNA

Bulletin

"NAVIGATION PRO (NBT EVO) MAP UPDATE NOT POSSIBLE, NAVIGATION DOES NOT START. A. Navigation system will not start at all or the ""Navigation system starts"" message is permanently displayed. B. While attempting to update the Navigation system's map, it will not update. Subfolder on internal Hard Disk Drive (HDD) is missing."

NHTSA · Herstellerbulletin10146776Modelljahre 2016Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Mini III · 2013–2024
BulletinMittelElektrikNA

Bulletin

Mini: The oil filter housing may leak coolant which will cause overheating. Activating the engine warning light and loss of power. *ma

NHTSA · Herstellerbulletin10059096Modelljahre 2014Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Ältere →

Quellen: NHTSA (USA, gemeinfrei), Transport Canada (Open Government Licence – Canada), DVSA (Vereinigtes Königreich, Open Government Licence v3.0), RappelConso und EU-Safety-Gate (Frankreich, Licence Ouverte 2.0).