Frei lesbar · kostenloses Konto zum MitmachenNachfolger von Anticars (2000)

Mini Mini

2001– · 5 generationen · 50 dokumentierte Mängel · 3 Märkte
Generationen

Technische Bulletins (TSB) sind Reparaturanweisungen, die Hersteller ihren Händlern zu bekannten Problemen schicken. Sie sind keine Sicherheitsrückrufe, bestätigen aber oft einen Mangel.

SchweregradAlleMittelGering
Modelljahr
Mini III · 2013–2024
BulletinMittelGetriebeNA

Bulletin

"B38, B46, and B48 Engines: Engine Noise, Drivability Complaints, and Various DME Faults. The vehicle exhibits one the following complaints: z Noise from the lower engine area, described as a high-pitched whine z Loss of power when idling z At a higher engine speed (above 3,000 rpm), a brief decrease in the engine speed can be felt. z Extended cranking before the engine will start z The customer notices an increased level of ""free play"" in the clutch pedal when changing gears. z The clutch pedal remains depressed, and will not return to the disengaged position. z Emergency operation is active, with one or more of the faults listed below. One or more of the following faults may be stored in the vehicle: z 160020 Crankshaft sensor, signal: implausible z 180001 Catalytic converter: efficiency too low z 200D0C Powertrain, safety function: bus signal rpm reduction implausible z 11A002 Fuel high pressure, plausibility: Pressure too low z 1F054D Powertrain, safety function: powertrain reduced power, DSC-signal implausible Note: If additional faults are found in the DME memory (e.g., misfire, camshaft sensor, knock sensor, etc.), then those faults will be the primary focus of the diagnosis using the test plans provided for those faults. ""FC 120408 Boost pressure control: Shut-down as a consecutive reaction"" is only a result of the component fault and is not the primary reason for the complaint or https://www.minitis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/286...1/4/2016 Page 2 of 2 illumination of the engine malfunction warning."

NHTSA · Herstellerbulletin10147907Modelljahre 2016Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Mini III · 2013–2024
BulletinMittelGetriebeNA

Bulletin

"B38, B46, and B48 Engines: Clutch Operation, Engine Noise, and Drivability Complaints. The vehicle exhibits one the following complaints: z The customer notices an increased level of ""free play"" in the clutch pedal when changing gears. z The clutch pedal remains depressed and will not return to the disengaged position. z Noise from the lower engine area described as a high-pitched whine z Loss of power when idling z At a higher engine speed (above 3,000 rpm), a brief decrease in the engine speed can be felt. z Extended cranking before the engine will start z Emergency operation is active with one or more of the faults listed below. One or more of the following faults may be stored in the vehicle: z 160020 Crankshaft sensor, signal: implausible z 180001 Catalytic converter: efficiency too low z 200D0C Powertrain, safety function: bus signal rpm reduction implausible z 11A002 Fuel high pressure, plausibility: Pressure too low z 1F054D Powertrain, safety function: powertrain reduced power, DSC-signal implausible Note: If additional faults are found in the DME memory (e.g., misfire, camshaft sensor, knock sensor, etc.), then those faults will be the primary focus of the diagnosis using the test plans provided for those faults. ""FC 120408 Boost pressure control: Shut-down as a consecutive reaction"" is only a result of the component fault and is not the primary reason for the complaint or illumination of the engine malfunction warning."

NHTSA · Herstellerbulletin10147908Modelljahre 2016Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Mini III · 2013–2024
BulletinMittelGetriebeNA

Bulletin

"?SI M12 04 15 Engine Electrical Systems June 2015 Technical Service This Service Information bulletin supersedes SI M12 04 15 dated March 2015. designates changes to this revision SUBJECT B38, B46, and B48 Engines: Engine Noise, Drivability Complaints, and Various DME Faults. The vehicle exhibits one the following complaints: ? Noise from the lower engine area, described as a high-pitched whine ? Loss of power when idling ? At a higher engine speed (above 3,000 rpm), a brief decrease in the engine speed can be felt. ? Extended cranking before the engine will start ? The customer notices an increased level of ""free play"" in the clutch pedal when changing gears. ? The clutch pedal remains depressed, and will not return to the disengaged position. ? Emergency operation is active, with one or more of the faults listed below. Faults stored in the vehicle: ? 160020 Crankshaft sensor, signal: implausible ? 180001 Catalytic converter: efficiency too low ? 200D0C Powertrain, safety function: bus signal rpm reduction implausible ? 11A002 Fuel high pressure, plausibility: Pressure too low ? 1F054D Powertrain, safety function: powertrain reduced power, DSC-signal implausible? 120408 Boost pressure control: Shut-down as a consecutive reaction"

NHTSA · Herstellerbulletin10147739Modelljahre 2016Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Mini III · 2013–2024
BulletinMittelGetriebeNA

Bulletin

"B38, B46 and B48 Engines: Drivability Complaints with Crankshaft Sensor Fault. The vehicle exhibits one of the following complaints: ? Loss of power when idling ? At a higher engine speed (above 3,000 rpm), a brief decrease in the engine speed can be felt. ? Extended cranking before the engine will start ? The customer notices an increased level of ""free play"" in the clutch pedal when changing gears. ? The clutch pedal remains depressed and will not return to the disengaged position. ? Emergency operation is active with one or more of the faults listed below. Faults stored in the vehicle: ? 160020 Crankshaft sensor, signal: implausible ? 180001 Catalytic converter: efficiency too low ? 200D0C Powertrain, safety function: bus signal rpm reduction implausible ? 11A002 Fuel high pressure, plausibility: Pressure too low ? 1F054D Powertrain, safety function: powertrain reduced power, DSC-signal implausible? 120408 Boost pressure control: Shut-down as a consecutive reaction"

NHTSA · Herstellerbulletin10147698Modelljahre 2016Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Mini III · 2013–2024
BulletinMittelGetriebeNA

Bulletin

"B38, B46, and B48 Engines: Clutch Operation, Engine Noise, and Drivability Complaints. The vehicle exhibits one the following complaints: ? The customer notices an increased level of ""free play"" in the clutch pedal when changing gears. ? The clutch pedal remains depressed and will not return to the disengaged position. ? Noise from the lower engine area described as a high-pitched whine ? Loss of power when idling ? At a higher engine speed (above 3,000 rpm), a brief decrease in the engine speed can be felt. ? Extended cranking before the engine will start ? Emergency operation is active with one or more of the faults listed below. Faults stored in the vehicle: ? 160020 Crankshaft sensor, signal: implausible ? 180001 Catalytic converter: efficiency too low ? 200D0C Powertrain, safety function: bus signal rpm reduction implausible ? 11A002 Fuel high pressure, plausibility: Pressure too low ? 1F054D Powertrain, safety function: powertrain reduced power, DSC-signal implausible? 120408 Boost pressure control: Shut-down as a consecutive reaction."

NHTSA · Herstellerbulletin10147224Modelljahre 2016Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Mini III · 2013–2024
BulletinMittelGetriebeNA

Bulletin

F54 ALL4: FAULT CODE 440317 STORED IN THE LMV. The following Check Control Message (CCM) is displayed in the instrument cluster: CCM 350: Driving stabilization. Drive at a moderate speed. The following entry is present in the fault memory of the LMV: 440317 - Pump motor: General multiple fault. Further fault memory entries can occur in combination: DSC: 48068C - Transfer box - clutch closed down temporarily, possible overheating. 48078A - All-wheel drive clutch - clutch position open, only front-wheel drive. LMV: 440304 - Pump motor: Current too low Unfavorable software of the longitudinal torque distribution module (LMV).

NHTSA · Herstellerbulletin10146975Modelljahre 2016–2017Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Mini III · 2013–2024
BulletinMittelGetriebeNA

Bulletin

Mini: Due to faulty installation of crankshaft sensor, catalytic converter, powertrain, fuel high pressure, and boost pressure control, customer complaints of noise from lower engine, loss of power, decrease in engine speed and depressed clutch pedal. *ma

NHTSA · Herstellerbulletin10059110Modelljahre 2016Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Mini II · 2006–2013
BulletinMittelGetriebeNA

Bulletin

Bmw(mini): Transmission - various egs faults caused by wiring harness damage. Difficult to engage the d or r gears from park position; gear shifts are extremely harsh during drive; intermittently the transmission warning light may be displayed. *pe

NHTSA · Herstellerbulletin10026570Modelljahre 2008Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Mini III · 2013–2024
BulletinGeringGetriebeNA

Bulletin

A Check Control message displays for Transmission oil service required (ID 2120). This warning can be triggered: From 60,000 miles (95,000 km) to 78,000 miles (125,000 km) After six years: The time interval of six years starts from the production date of the vehicle, not on the day of the first registration or the completion of the pre-delivery check (PDI). If the vehicle is driven more than approx. 1900 miles (3,000 km) after the first CCM, then a second message will be display for Transmission fault! (ID 368).

NHTSA · Herstellerbulletin11032775Modelljahre 2024Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Mini III · 2013–2024
BulletinGeringGetriebeNA

Bulletin

The upper crankshaft guide bearing may wear out prematurely. The wear on the guide bearing can cause the clutch pedal to malfunction during shifting.

NHTSA · Herstellerbulletin10216759Modelljahre 2014Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Mini III · 2013–2024
BulletinGeringGetriebeNA

Bulletin

The upper crankshaft guide bearing may wear out prematurely. The wear on the guide bearing can cause the clutch pedal to malfunction during shifting.

NHTSA · Herstellerbulletin10216760Modelljahre 2014Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Mini III · 2013–2024
BulletinGeringGetriebeNA

Bulletin

When the vehicle is on a lift and wheels are manually spun, a clanking noise is heard from the transmission area.

NHTSA · Herstellerbulletin10206695Modelljahre 2021Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Mini III · 2013–2024
BulletinGeringGetriebeNA

Bulletin

EGS FAULTS STORED AFTER AISIN TRANSMISSION REPLACEMENT. Due to hardware changes in the AISIN GA6F21AW or GA8F22AW transmissions.

NHTSA · Herstellerbulletin10163062Modelljahre 2016Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Mini III · 2013–2024
BulletinGeringGetriebeNA

Bulletin

The manual transmission gear shift knob easily comes off the shift rod with minimal upward force. The retaining tabs on the shifter knob do not hold securely to the shifter rod.

NHTSA · Herstellerbulletin10152334Modelljahre 2016Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Mini III · 2013–2024
BulletinGeringGetriebeNA

Bulletin

"The upper crankshaft guide bearing may wear out prematurely. The wear on the guide bearing can cause the clutch pedal to malfunction during shifting. The Engine Malfunction Warning may be illuminated and a fault will be stored in the DME memory for the crankshaft sensor. Noise may be heard from the lower engine and transmission bell housing area and engine damage can occur in rare occasions. This Service Action involves ""396"" F55 and F56 vehicles produced from January 2014 to February 2015. Vehicles which require this Service Action to be completed will show it as ""Open"" when checked either in the ""Service Menu"" of DCSnet (Dealer Communication System) or with the Key Reader. UN"

NHTSA · Herstellerbulletin10151287Modelljahre 2015–2016Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Mini III · 2013–2024
BulletinGeringGetriebeNA

Bulletin

"SI M11 02 16 February 2016 Engine Technical Service This Service Information bulletin supersedes SI M11 02 16 dated February 2016.. The upper crankshaft guide bearing may wear out prematurely. The wear on the guide bearing can cause the clutch pedal to malfunction during shifting. The Engine Malfunction Warning may be illuminated and a fault will be stored in the DME memory for the crankshaft sensor. Noise may be heard from the lower engine and transmission bell housing area and engine damage can occur in rare occasions. This Service Action involves ""382"" F55 and F56 vehicles produced from February 2014 to December 2014. Vehicles which require this Service Action to be completed will show it as ""Open"" when checked either in the ""Service Menu"" of DCSnet (Dealer Communication System) or with the Key Reader. UN"

NHTSA · Herstellerbulletin10151150Modelljahre 2015–2016Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Mini III · 2013–2024
BulletinGeringGetriebeNA

Bulletin

?SUBJECT Service Action: Program Control Units (DME) . A Check Control Message could intermittently be displayed indicating a Start/Stop Function failure. Vehicle may not restart after stopping. The following fault is stored in the DME: Fault 20BA20: clutch switch, signal: missing In addition the BDC may have the following fault stored: Fault 804084: clutch switch, plausibility fault compared to CAN signal This can occur if for example 14 gears changes are made, but the upper clutch position switch is only activated 10 times. This difference could occur when the clutch pedal is not being fully released between gear shifts or by resting a foot on the pedal so the upper switch position is not recognized.

NHTSA · Herstellerbulletin10151046Modelljahre 2016Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Mini III · 2013–2024
BulletinGeringGetriebeNA

Bulletin

Clutch Is Slipping or Grabbing. The customer states that the clutch is slipping or grabbing.

NHTSA · Herstellerbulletin10150145Modelljahre 2013Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Mini III · 2013–2024
BulletinGeringGetriebeNA

Bulletin

B38 and B48 Engines: Grease Residue Found at Bottom of Transmission Bell Housing. INFORMATION While performing repairs to the underside of the vehicle, the technician may notice yellow grease residue has formed on the lowest point of the transmission bell housing near the engine starter. The residue is not related to the engine oil or transmission fluid. The grease was applied to the starter during vehicle assembly. If the residue is noticed, the grease can be wiped away with a shop towel. The residue will stop accumulating after the engine has been operated for a few hundred miles. If the residue were to drip from the bell housing, it would be caught by the under body covering and would not create a customer complaint. In a severe case, some marks may be seen on the engine side of the under body covering. The grease drippings will not be seen on the ground under the vehicle. Do not remove or replace any components.

NHTSA · Herstellerbulletin10148295Modelljahre 2014Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Mini III · 2013–2024
BulletinGeringGetriebeNA

Bulletin

"Engine Power Reduction with ""Clutch Damaged"" Faults Stored. A drivetrain malfunction check control message is displayed, prompting the customer to contact the dealer for a service visit. The vehicle drives normally, but fault(s) for a damaged clutch are stored in the DME. ? 1D3101 - Clutch: Damaged, transmittable torque too low ? 1D3201 - Clutch: Severely damaged, transmittable torque too low CAUSE 1. The DME software diagnostic for detecting excessive clutch slip is too sensitive. 2. The clutch is damaged."

NHTSA · Herstellerbulletin10147741Modelljahre 2016Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Mini III · 2013–2024
BulletinGeringGetriebeNA

Bulletin

"eAutomatic Transmission Selector Lever Will Not Move Out of Park. The transmission selector lever cannot be disengaged from the ""P"" position. This can occur very randomly and is difficult to reproduce. No faults are stored in the EGS control unit, and no warnings are displayed in the instrument cluster. For the most part, if the vehicle is locked and goes to sleep (the light in the hazard switch goes out), the problem is no longer present. Unfavorable EGS software"

NHTSA · Herstellerbulletin10147111Modelljahre 2016Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Mini III · 2013–2024
BulletinGeringGetriebeNA

Bulletin

Service Action: B38 Engine - Check and Replace Crankshaft Guide Bearing. The upper crankshaft guide bearing may wear out prematurely. The wear on the guide bearing can cause the clutch pedal to malfunction during shifting. The Engine Malfunction Warning may be illuminated and a fault will be stored in the DME memory for the crankshaft sensor. Noise may be heard from the lower engine and transmission bell housing area and engine damage can occur in rare occasions.

NHTSA · Herstellerbulletin10146973Modelljahre 2016Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Mini III · 2013–2024
BulletinGeringGetriebeNA

Bulletin

Service Action: B46 and B48 Engines - Check and Replace Crankshaft Guide Bearing. The upper crankshaft guide bearing may wear out prematurely. The wear on the guide bearing can cause the clutch pedal to malfunction during shifting. The Engine Malfunction Warning may be illuminated and a fault will be stored in the DME memory for the crankshaft sensor. Noise may be heard from the lower engine and transmission bell housing area and engine damage can occur in rare occasions.

NHTSA · Herstellerbulletin10146867Modelljahre 2016Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Mini III · 2013–2024
BulletinGeringGetriebeNA

Bulletin

GROANING NOISE WITH CLUTCH OPERATION. Clutch operation may exhibit the following characteristics: produces a groaning noise, especially when engine is at operating temperature, during stopand-go travel. noise comes from transmission housing. noise can be heard in the interior and exterior of the vehicle. Friction between clutch slave cylinder piston rod end and ball socket (thrust piece).

NHTSA · Herstellerbulletin10146870Modelljahre 2016Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Mini III · 2013–2024
BulletinGeringGetriebeNA

Bulletin

Service Action: B38 Engine - Check and Replace Crankshaft Guide Bearing. The upper crankshaft guide bearing may wear out prematurely. The wear on the guide bearing can cause the clutch pedal to malfunction during shifting. The Engine Malfunction Warning may be illuminated and a fault will be stored in the DME memory for the crankshaft sensor. Noise may be heard from the lower engine and transmission bell housing area and engine damage can occur in rare occasions.

NHTSA · Herstellerbulletin10146800Modelljahre 2016Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Ältere →

Quellen: NHTSA (USA, gemeinfrei), Transport Canada (Open Government Licence – Canada), DVSA (Vereinigtes Königreich, Open Government Licence v3.0), RappelConso und EU-Safety-Gate (Frankreich, Licence Ouverte 2.0), MLIT (Japan, Public Data License 1.0) und MOLIT (Südkorea, car.go.kr).