On certain vehicles, the bracket that is the anchor point for the left rear fuel tank mounting strap may have been improperly formed during the manufacturing process. This may have caused the metal to spilt in the area where the bolt holds the fuel strap to the underside of the vehicle. In the event the tank is full of fuel and the vehicle is involved in a serious collision the bracket could break and the tank could drop down. This situation could result in a fuel leak and the possibility of a fire. Correction: Dealers will inspect and if necessary install a reinforcement cap to the fuel tank bracket.
Transport Canada10. Okt. 20082008374Modelljahre 2006–2007Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Mitsubishi is recalling 45,988 my 2005-2007 endeavor, galant, eclipse coupe, and my 2007 eclipse spyder vehicles. The bracket that is the attachment point for the left rear fuel tank mounting strap may have been improperly formed during a metal stamping process. The process may have caused the metal to have a split in the area where the bolt that holds one of the two fuel tank straps to the underside of the vehicle is located. In the event the fuel tank is full and the vehicle is subject to a severe collision, the bracket may break and allow the fuel tank to drop down, possibly causing a fuel leak.
On certain passenger vehicles, the metal forming part of the front crossmember may have been improperly stamped resulting in the metal becoming thinner in the cross-section than specified. This could, over time, result in breakage of the crossmember.
Mitsubishi Motors North America, Inc. (MMNA) is recalling certain model year 2006-2009 Eclipse vehicles manufactured April 20, 2005, to February 13, 2009, and 2007-2009 Eclipse Spyder vehicles manufactured December 23, 2005, to February 13, 2009. Due to corrosion inside the antil-lock brake system (ABS) unit, one or more of the internal valves may seize. In a braking event that uses the ABS, a seized valve would increase brake pedal travel and reduce braking ability.
NHTSA · USA2. Juni 201515V337000Modelljahre 2006–2009Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
On certain vehicles, corrosion may occur in the ABS hydraulic unit due to a reaction between the brake fluid and the surface treatment of the internal valves. If this were to occur and the ABS hydraulic unit is activated, one or more of the valves could seize. This could result in longer brake pedal travel and increased stopping distances, which may increase the risk of a crash causing injury and/or damage to property. Correction: Dealers will flush and clean the hydraulic unit by replacing the brake fluid with higher grade (DOT4) fluid. If module valve movement is determined to be poor, the ABS hydraulic unit will be replaced.
Transport Canada22. Mai 20152015219Modelljahre 2006–2009Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
On certain vehicles equipped with automatic transmissions, the key lock cable was improperly manufactured and may not allow the cable end to lock into the floor shifter mechanism. This can result in the interlock system to become inoperative and allow the ignition key to be removed without the gearshift mechanism being placed in the park position.
On certain passenger vehicles, one of four seals inside the master cylinder may have been installed improperly. As a result, the master cylinder may unexpectedly by-pass hydraulic braking force pressure and allow a longer than normal pedal stroke.
NHTSA · USA27. Juni 200505V299000Modelljahre 2006Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Quellen: NHTSA (USA, gemeinfrei), Transport Canada (Open Government Licence – Canada), DVSA (Vereinigtes Königreich, Open Government Licence v3.0), RappelConso und EU-Safety-Gate (Frankreich, Licence Ouverte 2.0), MLIT (Japan, Public Data License 1.0) und MOLIT (Südkorea, car.go.kr).