Steering:Gear box (other than rack and pinion)
The steering intermediate shaft could have been improperly assembled causing the shaft lower coupling to loosen and rotate on the steering gear input shaft.
🔔 Kostenloses Konto anlegen und Benachrichtigungen zu Pontiac Firebird (alle generationen) erhalten
The steering intermediate shaft could have been improperly assembled causing the shaft lower coupling to loosen and rotate on the steering gear input shaft.
These vehicles may have been built with an improperly assembled steering intermediate shaft. This condition could cause the intermediate shaft lower coupling to loosen and rotate on the steering gear input shaft. If this were to occur while the vehicle was in motion, a loss of steering control could result and a crash could occur without prior warning. Correction: Steering shaft will be inspected and lower coupling will be replaced if required.
Die Lötverbindung am Tankeinfüllstutzen kann Risse oder Nadelporenlecks entwickeln, was nicht der FMVSS Nr. 301, „Fuel system integrity“, entspricht. Die Risse und Löcher können Kraftstoffdampf und Kraftstoffaustritt zulassen.
Diese Fahrzeuge könnten Risse oder "Pinholes" (feine Lecklöcher) an der Lötverbindung des Tankeinfüllstutzens aufweisen. Dies könnte zu Kraftstoffgeruch oder Kraftstoffaustritt führen. Bei Vorhandensein einer Zündquelle könnte ein Kraftstoffaustritt aufgrund dieses Zustands einen Fahrzeugbrand verursachen. Korrektur: Kraftstofftanks an betroffenen Fahrzeugen werden auf Undichtigkeiten geprüft und bei Bedarf ersetzt.
Note: Vehicle located in ontario. The fuel line could develop a hole due to contact with the hot air (air injection reaction) check valve. This could result in fuel leakage and an engine compartment fire. Correction: Fuel line bundle will be inspected for heat damage and replaced if necessary. Fuel line bundle will also be rerouted.
The fuel lines on these vehicles may have been misrouted and may contact the "air" check valve. The high temperatures from the "air" check valve could allow it to melt through and damage a fuel line.
Fuel feed hoses may pull out of the crimped coupling at the engine end of the hose assembly.
Fuel return hoses may break at either crimped coupling.
Note: Vehicles equipped with 5.0 litre and 5.7 litre engines. Vehicles may have fuel return hoses which could break at either or both crimped couplings. If a coupling were to separate, fuel leakage and a possible engine compartment fire could result. Correction: A properly crimped fuel return hose will be installed on all involved vehicles.
Note: Vehicles equipped with 2.8.L v6 engines. The fuel feed hoses may pull out of the crimped coupling at the engine end of the hose assembly. This could result in fuel leakage and an engine compartment fire. Correction: A redesigned fuel feed hose will be installed on all involved vehicles.
The hub area of the wheels may not be structurally sound and thus subject to fracture. Consequence of defect: The wheels could separate from the car causing a loss of control. This could result in an accident without prior warning.
Due to undersized grinding at the time of manufacture, the rear brake centre flex hoses could separate from the end fittings when subjected to the pull force required by cmvss 106-74. Tensile strangth test. Such a separation would result in loss of brake fluid and a partial loss of braking action. Should this happen while the vehicle is in motion, at a time when minimum stopping distances are required, a vehicle crash could occur without prior warning.
The involved vehicles do not conform to federal motor vehicle safety standard no. 210, "seat belt assembly anchorages". The non-compliance exists because the rear seat belt anchorages may pull through the underbody of the vehicle if enough force is applied.
Fuel tank ventilator valve in the fuel system may produce a loud and persistent "whistle" during venting of the tank. If the fuel filler cap is removed while this condition exists and the tank is more than 3/4 full, gasoline may be forced out of the filler neck onto bystanders.
Bei bestimmten Fahrzeugen enthalten die Gurtaufroller an den hinteren Sitzplätzen erste Verriegelungsstellen, die bei Verwendung durch kleinere Mitfahrer nicht einrasten. Dies entspricht nicht den Anforderungen der Bundesnorm für Kraftfahrzeugsicherheit Nr. 208 („Insassenschutz bei Unfällen“).
Bestimmte Personenkraftwagen erfüllen die Anforderungen der FMVSS Nr. 208, „Insassenschutz bei Unfällen", und Nr. 214, „Seitenaufprallschutz", nicht. Bei diesen Fahrzeugen können Schweißnähte in der Nähe des unteren Scharniers der Fahrertür nicht den Spezifikationen entsprechen.
Fahrzeugbeschreibung: Personenkraftwagen mit Schaltgetriebe. Der Kupplungsgeberzylinder wurde möglicherweise mit einem falschen Sicherungsring gefertigt.
Hinweis: Fahrzeuge mit 5,7-Liter-Motoren. Das Abgasrückführventil (EGR-Ventil) könnte aufgrund von innerer Korrosion ausfallen. Dadurch könnte das Fahrzeug die geltenden Emissionsvorschriften nicht erfüllen. Korrektur: Händler prüfen das EGR-Ventil anhand der Teilenummer und ersetzen es bei Bedarf durch ein EGR-Ventil in neuer Bauart.
Note: Convertible vehicles. These vehicles do not comply with c.M.V.S.S. 209 - seat belt assemblies. The front seat belt retractors may lock-up on slopes less severe than the requirement of the standard. As a result, occupants may not be able to extract and fasten their seat belts until the vehicle is moved to a more level surface. Correction: Dealers will inspect for proper front seat belt retractor position and those found to be improperly positioned will be reinstalled correctly.
These vehicles were manufactured with seat belt retractors out of design position which can cause the retractor to lock-up on slopes less severe than the fmvss requirement. This does not comply with fmvss no. 209, "seat belt assemblies."
Hinweis: Betroffen sind Fahrzeuge mit Automatikgetrieben vom Typ 4L60. Der Schaltseilmantel kann sich lösen und verhindern, dass das Getriebe in die richtige Stellung geschaltet wird. Beispielsweise kann sich der Getriebeschalthebel in der Stellung P (Park) befinden, obwohl das Getriebe tatsächlich in D (Drive) oder R (Reverse) steht. Dieser Zustand kann zu unerwarteter Fahrzeugbewegung führen und ohne vorherige Warnung einen Fahrzeugunfall verursachen. Abhilfe: Bei betroffenen Fahrzeugen wird ein überarbeiteter Schaltkulissenhebel eingebaut.
The automatic transmission shift control cable can separate.
These vehicles may not comply with c.M.V.S.S. 209 - seat belt assemblies. - seat belt latch plates may not engage or may do so only after wiggling and/or forcing the latch plate. Correction: Vehicles will be inspected and suspect retractor side safety belt assemblies (which include latch plates) will be replaced if necessary.
The metal latchplates may not engage the buckle assemblies, causing a "no latch" condition. Movement of the seat occupant in this condition could cause latchplate release from the buckle.
On certain vehicles, the parking brake system may contain a non-functional parking brake adjuster. This may result in a gradual loss of parking brake effectiveness as the rear disc pads wear. As a result, the parking brake may not hold the vehicle on a steep incline. If the vehicle is parked with the transmission in neutral or a forward gear, the vehicle may roll away and result in personal injury or property damage. Correction: A new parking brake adjuster will be installed.
Quellen: NHTSA (USA, gemeinfrei), Transport Canada (Open Government Licence – Canada), DVSA (Vereinigtes Königreich, Open Government Licence v3.0), RappelConso und EU-Safety-Gate (Frankreich, Licence Ouverte 2.0), MLIT (Japan, Public Data License 1.0) und MOLIT (Südkorea, car.go.kr).