The body mounting panels of the rear seatbelt buckle anchorages have been made using an incorrect grade of material. In the event of an impact accident, if the rear centre seat is occupied at the same time as an outer rear seat, the rear seatbelt buckle may become detached from the bodywork, leading to injuries.
EU Safety GateJan 24, 2019A12/0161/19Model years 2012–2018View details →
Issue: On certain vehicles, the mounting points for the rear seat belts may not be properly manufactured. This could cause a seat belt to fail in a crash. Safety Risk: An occupant that is not properly restrained has a greater chance of being injured in a crash. Corrective Actions: The company will notify owners by mail. Owners will be instructed to take their vehicle to an authorized dealer to have the body structure modified to improve the strength of the rear seat belt mount.
Transport CanadaJan 17, 20192019026Model years 2012–2018View details →
Bentley Motors, Inc. (Bentley) is recalling certain 2012-2018 Bentley Mulsanne vehicles. In the event of a crash, the rear seat belt anchor may detach from the vehicle. As such, these vehicles fail to comply to Federal Motor Vehicle Safety Standard (FMVSS) number 210, "Seat Belt Assembly Anchorages."
NHTSA · United StatesJan 15, 201919V033000Model years 2012–2018View details →
Bentley is recalling 14 my 1980-1982 bentley t2, my 1980-1987 continental, and mulsanne, my 1980-1982 rolls-royce silver shadow ii, my 1980 silver wraith ii, my 1980-1987 corniche, silver spirit and my 1981-1987 silver spur passenger vehicles. A fuel hose assembly, available as a replacement part, has been found to have a defect in the material specification of the rubber hose. The hose may degrade under certain operating conditions resulting in a fuel leak.
NHTSA · United StatesNov 7, 200808V585000Model years 1980–1987View details →
The engine oil cooler pipe may come into contact with a hydraulic system pipe that connects to the right front brake caliper. This could cause fretting of the hydraulic pipe, potentially resulting in a hydraulic fluid leak and loss of braking efficiency. Correction: A protective shield will be installed to prevent contact between the pipes.
Transport CanadaApr 23, 19901990064Model years 1989–1990View details →
There is insufficient clearance between the right front brake caliper hydraulic line and the engine oil cooler line. If the lines come in contact with each other, the chafing may damage the brake line and cause a fluid leak.
NHTSA · United StatesApr 12, 199090V073000Model years 1989–1990View details →
The body panel to which the rear center seat belt and buckle are attached lacks sufficient strength. Therefore, if one or both of the rear left and right seats are occupied, the panel may be damaged in a vehicle collision, and the occupant of the rear center seat may not be properly restrained.
Bentley Motors, Inc. (Bentley) is recalling certain 2018 Bentley Mulsanne and 2018 Bentayga vehicles. When reverse gear has been selected, the rearview camera display may be obstructed or may not be fully visible within two seconds. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 111, "Rearview Mirrors."
NHTSA · United StatesSep 14, 201818V632000Model years 2018View details →
A wire inside the electric motor driven gearbox actuator may come into contact with the inner face of the assembly case, causing fretting of the wire and also causing the fuse protecting the circuit to blow if this occurs it would not be possible to engage the desired gear range and may not be possible to restart the vehicle after the engine has been switched off. If "park" is not engaged and the driver does not apply the parking brake, a roll away could occur. Correction: Affected wire will be repositioned.
Transport CanadaSep 28, 19951995169Model years 1992–1993View details →
An incorrectly positioned wire within the electrically operated gearbox actuator can chafe against the cover causing the transmission selector fuse to blow.
NHTSA · United StatesAug 17, 199595V159000Model years 1992–1993View details →
The fuse in the rear window demister circuit may fail, disabling the rear stop lamps other than the high mounted stop lamp. Correction: An additional fused circuit to handle only the main stop lamps will be installed.
Transport CanadaMar 5, 19901990041Model years 1990View details →
The micro-switch for the stop lamps may fail, causing the lamps to remain continuously illuminated or to fail to illuminate. If this occurs, application of the brakes would not be signalled to following vehicles, creating the potential for a collision. Correction: Stop lamp switch will be replaced with an improved switch.
Transport CanadaApr 7, 19891989049Model years 1986–1989View details →
Sources: NHTSA (United States, public domain), Transport Canada (Open Government Licence – Canada), DVSA (United Kingdom, Open Government Licence v3.0), RappelConso and EU Safety Gate (France, Licence Ouverte 2.0), Japan's MLIT (Public Data License 1.0) and South Korea's MOLIT (car.go.kr).