Free to read · free account to contributeSuccessor to Anticars (2000)

BMW 7 Series E32

1986–1994 · 5 documented defects · 4 markets
Model year
MarketAllNA
RecallCriticalInteriorNA

Airbag

On certain 318I, 318IS, 325I, 325IS, 525I, 525IT, 535I, 735I, 735IL, 750IL, 850I and M5, the locking tab for the airbag contact ring in the steering wheel assembly could break without warning. If this happens it is possible that the contact ring wiring could break. This would cause the readiness indicator lamp ("SRS" or "AIRBAG") to illuminate and in such a case the airbag would not be available for deployment in a frontal impact. Correction: Locking tab will be replaced with one of a different design.

Transport CanadaOct 7, 19961996159Model years 1991–1992View details →
RecallCriticalInteriorNA

Air bags:Frontal

The air bag contact ring locking tab located in the steering wheel assembly can break without warning.

NHTSA · United StatesJul 1, 199696V110000Model years 1991–1992View details →
RecallCriticalEngineNA

Fuel System

On certain 318I, 318IC, 318IS, 325IC, 325IS, 325IX, 525I, 535I, 735I and 735IL vehicles, the fuel feed hose could harden and "set" over time due to engine compartment temperatures. If this "setting" occurs, it is possible that seepage between the hose and fitting could result because the clamp cannot provide sufficient sealing force to compensate for the hardening of the hose. Fuel seepage, in the presence of an ignition source, could result in an engine compartment fire. Correction: fuel feed hoses and associated clamps will be replaced with ones of a new design.

Transport CanadaMay 30, 19941994096Model years 1989–1993View details →
RecallCriticalEngineNA

Fuel system, gasoline:Delivery:Hoses, lines/piping, and fittings

Feed fuel hoses can harden and "set" over time, allowing a seepage of fuel at the connection between the hose and the engine fitting. The clamp used to hold the hose to the fitting is unable to compensate for the hardening of the feed fuel hose.

NHTSA · United StatesApr 11, 199494V066000Model years 1989–1993View details →
RecallModerateInteriorNA

Heater And Defroster

On certain vehicles, failure of a cooling system component such as thermostat, water pump or fan belt can result in a significant increase in coolant temperature and system pressure. Increased system pressure could result the formation of a crack or separation of a seam in the heater core end piece which would cause hot coolant to be expelled from the heater core. This hot fluid could contact car occupants resulting in possible personal injury and/or fogging of the interior window surfaces. Correction: Radiator cap will be replaced with a new design cap in order to avoid buildup of excessive pressure in the cooling system.

Transport CanadaOct 14, 19981998197Model years 1988–1993View details →
RecallModerateEngineNA

Engine and engine cooling:Cooling system

Vehicle description: Passenger vehicles. A malfunction or failure of a coolant system component, such as a thermostat, water pump, or fan belt, can result in significantly increased coolant temperature and system pressure. If the indications of a critical overheating condition is not noticed by the driver, it is possible that damage to, or failure of, a coolant system component could occur.

NHTSA · United StatesAug 4, 199898V178000Model years 1988–1993View details →
RecallModerateEngineNA

Engine

On certain 318IC, 318IS, 318TI, 325I, 325IC, 325IS, 525I, 525IT, 530I, 530IT, 540I, 740I, 740IL, 840CI and M3, the cruise control and throttle cable are attached to the same throttle valve actuating lever at the throttle housing. It is possible that the plastic bushing on either cable could break causing the outer cable housing to separate from the bushing. Throttle pedal application without cruise control engagement could cause the outer tube to catch on the edge of the broken bushing resulting in the throttle valve remaining partially open. If this were to occur, the car might not decelerate as expected and a crash could occut. Correction: A spring clip will be installed on the outer tube of each cable to prevent dislodgment from the bushing.

Transport CanadaOct 9, 19971997173Model years 1993View details →
RecallModerateEngineNA

Vehicle speed control

The cruise control and throttle cables are attached to the same throttle valve actuating lever at the throttle housing. It is possible that the plastic bushing on either cable could break due to environmental influences coupled with vibration. If the bushing breaks, the outer cable housing can separate from the bushing. In this case, during application of the throttle pedal without cruise control being engaged, the outer tube could catch on the edge of the broken bushing.

NHTSA · United StatesAug 19, 199797V131000Model years 1993View details →
RecallModerateElectricalNA

Lights And Instruments

On certain 325I, 325IC, 325IS, 525I, 525IT, 530I, 530IT, 535I, 540I, 735I, 735IL, 740I, 740IL and 750I, the brake light switch may fail due to a reduction of contact force on the "snap contact" system which the switch incorporates. This could cause heat induced distortion of the plastic internal switch parts in the area of the electrical contacts. This could cause the switch to remain either in the ON or the OFF position resulting in the brake lights being continuously illuminated or inoperative regardless of brake pedal operation. Correction: Switch will be replaced with on that utilizes a different contact system.

Transport CanadaOct 7, 19961996158Model years 1990–1993View details →
RecallModerateBrakesNA

Exterior lighting:Brake lights:Switch

The brake light switch can fail allowing the switch to remain in the "brake lights off" position or in the "brake lights on" position.

NHTSA · United StatesJul 1, 199696V111000Model years 1990–1993View details →
RecallModerateEngineNA

Engine

On certain 740IA and 740ILA vehicles, the inner throttle cable could break due to a smaller than specification bend in the cable tube. If this were to occur, throttle control would be lost and the engine would return to or remain at idle. Correction: Throttle cable will be replaced with one meeting BMW specifications.

Transport CanadaApr 25, 19941994081Model years 1993View details →
RecallModerateEngineNA

Vehicle speed control:Cables

The throttle cable's tube (outer casing) contains a bend that leads to increased loading of the inner cable, causing it to break.

NHTSA · United StatesJan 3, 199494V022000Model years 1993View details →
RecallModerateEngineNA

Engine

On certain 535I, 535IA, 735IA, 735ILA vehicles, the nut which secures the throttle valve shaft may not have been tightened with sufficient torque. If the nut were to loosen, it is possible that movement of the throttle valve might be impaired. If this should occur, the vehicle might not decelerate as expected after the gas pedal is released and loos of vehicle control could result. Correction: Vehicles will be inspected and affected throttle housings with undertorqued throttle valve retaining nuts will be replaced.

Transport CanadaOct 13, 19921992129Model years 1991View details →
RecallModerateEngineNA

Vehicle speed control

Some of these vehicles are equipped with a throttle housing on which the throttle valve shaft retaining nut was not sufficiently tightened.

NHTSA · United StatesJul 10, 199292V101000Model years 1991View details →
RecallModerateInteriorNA

Seats And Restraints

On certain 525I, 535I, 735I, 735IL and 750IL vehicles, the front seat center fold-down armrest may contact and damage the seatbelt buckle if the seat back is moved forward to an upright position while the armrest is locked in the down position (horizontal). If this occurs, the release button may be held in the down position, preventing the seatbelt from being latched during the buckle-up operation. Non-latching of the seatbelts will increase the risk of personal injury in the event of a crash. Correction: Front seat safety belt buckles will be replaced with shorter ones that are not susceptible to damage by contact with the armrest.

Transport CanadaFeb 27, 19901990037Model years 1988–1990View details →
RecallModerateInteriorNA

Seat belts:Front:Buckle assembly

Under certain conditions, front seat center, fold-down arm rest may contact the safety belt buckle, causing damage to the release button and preventing the belt tongue from latching when buckling up.

NHTSA · United StatesJan 30, 199090V016000Model years 1988–1990View details →
RecallModerateEngineNA

Emissions

Certain 750IL vehicles fail to comply with the requirements of CMVSS 1103 - Exhaust Emissions.

Transport CanadaMay 2, 19891989063Model years 1988–1989View details →
RecallModerateEngineNA

Emissions

Certain 750IL vehicles fail to comply with the requirements of CMVSS 1103 - Exhaust Emissions

Transport CanadaMay 2, 19891989062Model years 1988–1989View details →
RecallModerateEngineNA

Engine

On certain 750IL vehicles, during the assembly process, the gas pedal may not have been properly attached to the floor pan. If the gas pedal is operated in a rough or erratice manner, it may become stuck between the gas pedal stop (on the floor pan) and the carpeting on the transmission tunnel. If this occurs, the pedal might not return fully to the idle position when the driver's foot is removed and loss of control could result. Application of the brake pedal will close the throttle on this model of vehicle. Correction: Accelerator pedal will be inspected and tightened to the floor is required. Also, a modified pedal stop will be installed.

Transport CanadaApr 6, 19891989046Model years 1988–1989View details →
RecallModerateElectricalNA

Electrical

On certain 325E, 325ES, 528E, 535I, 635CSI and 735I vehicles, the center high mounted brake light could add sufficient electrical load to cause the brake light switch to overheat, eventually leading to melting of the plastic internal switch parts. This could cause the switch plunger to jam in the ON or OFF position. This would render the brake light permanently ON or OFF regardless of brake pedal operation. Correction: A brake light switch with an increased current load capacity will be installed on affected vehicles.

Transport CanadaNov 27, 19861986134Model years 1986–1987View details →
RecallMinorInteriorNA

Seats And Restraints

On certain 725I, 735IA and 750IL vehicles, on the front seats, the seatbacks may not have been fully seated on the recliner arms. This could result in looseness of, or noise in the seat. In extreme cases, during a severe rear impact, the seatback may not support the occupant and increase the risk of injury. Correction: Seatbacks will be inspected and properly seated if required.

Transport CanadaAug 25, 19881988124Model years 1988View details →
RecallMinorInteriorNA

Seats

The driver and/or passenger seatbacks may not have been fully attached to the seat base reclining arms (attaching brackets).

NHTSA · United StatesAug 11, 198888V135000Model years 1988View details →

Sources: NHTSA (United States, public domain), Transport Canada (Open Government Licence – Canada), DVSA (United Kingdom, Open Government Licence v3.0), RappelConso and EU Safety Gate (France, Licence Ouverte 2.0), Japan's MLIT (Public Data License 1.0) and South Korea's MOLIT (car.go.kr).