Vehicle description: Certain passenger vehicles, equipped with sunvisor located air bag labels, fail to conform to federal motor vehicles safety standard no. 208, "occupant crash protection." these vehicles have a message area less than 30 cm which does not meet the requirements of the standard.
NHTSA · United StatesApr 6, 200101V109000Model years 2000–2001View details →
Vehicle description: Passenger vehicles. Some of these vehicles exhibit a condition in which the driver side impact air bag inflator separates from the air bag module during deployment.
NHTSA · United StatesNov 13, 200000V371000Model years 2000–2001View details →
Some of these vehicles with the key in the "on" position, exhibit a condition in which the antilock brake system (abs) motor shorts to its case and grounds through a flexible brake fluid pipe.
NHTSA · United StatesJul 9, 199999V170000Model years 1999View details →
Note: Vehicles located in ontario(4) and british columbia(1). These vehicles may have an under torqued right hand front spindle nut. If this nut were to fall off, the wheel could separate from the vehicle possibly resulting in a crash without prior warning. Correction: Vehicles will be inspected and if the right hand front spindle nut is under torqued, the wheel bearing assembly and nut will be replaced.
Transport CanadaOct 4, 19941994151Model years 1994View details →
The right hand spindle nut was not properly tightened during assembly. This can cause premature wheel bearing failure and over time, the spindle can fracture.
NHTSA · United StatesOct 4, 199494V189000Model years 1994View details →
The power door lock relay on these vehicles can short internally due to water intrusion. This condition may result in a vehicle fire. Correction: Power door lock relay and any corroded terminals will be replaced. In addition, the new relay will be relocated to an area where water intrusion is less likely
Transport CanadaSep 7, 19941994141Model years 1994View details →
The power seat or recliner wiring harness can be pinched or can chafe on the seat frame or spring support rod, wearing through the wire insulation and causing an electrical short.
NHTSA · United StatesSep 1, 199292V124000Model years 1990–1991View details →
The fuel feed hose could leak at the coupling on the engine end of the hose assembly. This condition could allow fuel to leak into the engine compartment and possibly result in an engine compartment fire. Correction: Fuel feed hose assembly will be inspected and replaced if necessary with a new hose assembly.
Transport CanadaDec 5, 19881988166Model years 1988View details →
On certain vehicles, excessive enlargement of a pilot hole in the rear brake backing plate could allow the wheel cylinder to rotate possibly leading to loss of brake fluid in the rear brakes and loss of rear braking capability.this Would result in increased stopping distances and possible crash. note: vehicles in ontario and quebec only.
Transport CanadaMay 28, 19861986056Model years 1980–1984View details →
The generator "bat" terminal located on the rectifier end frame may contact the carburetor fuel inlet pipe. Consequence of defect: The "bat" stud may rub through the terminal boot and contact the fuel pipe which could result in an underhood fire and cause burn injuries to the occupant.
NHTSA · United StatesOct 4, 198585V122000Model years 1986View details →
Excessive enlargement of the wheel cylinder pilot hole in the rear brake backing plate could allow the wheel cylinder to rotate and cause loss of brake fluid. Consequence of defect: A loss of brake fluid leads to loss of rear brake action, creating the potential for an accident. Front brakes would remain operational.
NHTSA · United StatesApr 29, 198585V048000Model years 1980View details →
On vehicles with 2.5l engines. The fuel system may leak at the throttle body injection fuel feed pipe connection presenting the possibility of an underhood fire.
Transport CanadaMar 29, 19851985032Model years 1984View details →
The fuel system may leak at the throttle body injection fuel feed pipe connection. Consequence of defect: This leakage could result in an underhood fire which could spread to the passenger compartment and cause burn injuries to occupants.
NHTSA · United StatesMar 29, 198585V034000Model years 1984View details →
The axle retaining "c" clip in the differential may dislodge and allow the axle, wheel and brake drum to separate from the vehicle when subjected to side forces. Axle separation could result in loss of vehicle control and possible crash.
Transport CanadaJan 11, 19851985010Model years 1980View details →
The brake proportioner valves may break and separate from the master cylinder during braking. This will result in a loss of brake fluid and a partial loss of braking action
Transport CanadaOct 7, 19841983084Model years 1983View details →
The rear brake hoses were not fully seated into their fittings when the fittings were crimped onto the hose at the time of manufacture. Hose failure would cause loss of brake fluid and partial loss of braking action thereby increasing stopping distance.
Transport CanadaJan 26, 19831983009Model years 1982View details →
Under certaain conditions, the hose clamps on the fuel tank filler pipe and fuel tank filler vent pipe could fracture. The fracture of these clamps could cause fuel leakage at any of the four pipe to hose connections. Leakage can occur during refueling, or while driving, if the fuel tank is above 3/4 full.
NHTSA · United StatesMar 8, 198282V021000Model years 1982View details →
Under certain conditions the hose clamps on the fuel filler pipe and fuel tank filler vent pipe could fracture. This could cause seepage of fuel at any one of the four pipe to hose connections when the fuel tank is above 3/4 full creating the possibility of fire.
Transport CanadaMar 3, 19821982026Model years 1982View details →
"tx" heavy duty wheels may have been manufactured with laminated steel. The wheel disc may fracture and the wheel and tire could partially or completely separate from the vehicle.
NHTSA · United StatesMar 23, 198181V036000Model years 1981View details →
Certain passenger vehicles do not conform to the requirements of federal motor vehicle safety standard no. 108, "lamps, reflective devices, and associated equipment." some of these vehicles do not meet the overhead sign illumination requirements.
NHTSA · United StatesAug 10, 200404V375000Model years 1999View details →
Certain vehicles do not comply with the requirements of CMVSS 101 - Location and Identification of Controls and Displays. Vehicles exhibit a condition in which the "Oil Warning Light" will not illuminate under low/no oil pressure conditions. Correction: Dealers will reflash the vehicle PCM with new calibration software.
Transport CanadaApr 12, 20012001094Model years 1998View details →
Sources: NHTSA (United States, public domain), Transport Canada (Open Government Licence – Canada), DVSA (United Kingdom, Open Government Licence v3.0), RappelConso and EU Safety Gate (France, Licence Ouverte 2.0), Japan's MLIT (Public Data License 1.0) and South Korea's MOLIT (car.go.kr).