A defect in the gas generator of the passenger airbag may cause uncontrolled inflation and the release of metal fragments when the airbag is activated, which can cause injuries to the occupants.
EU Safety GateAug 14, 2020A12/00356/20Model years 2011View details →
In the driver-side airbag inflators (inflation devices), an investigation of market-recalled units from another manufacturer confirmed some units with large variation in the density of the gas-generating agent. Because of this, the cause has not been identified, and there is a risk that the airbag may not deploy normally when it is triggered.
Investigation of market-recovered units of the driver-side airbag inflator (inflation device) confirmed that some inflator housings have airtightness defects. Therefore, over long periods of use, atmospheric moisture may enter the inflator interior, causing the gas generant to absorb moisture, which may prevent the airbag from deploying properly when it is activated.
In the driver's side airbag inflators, improper moisture control after the gas generant is loaded during inflator manufacturing means that, under the influence of outside temperature and other factors during use, some gas generants swell and their density decreases. As a result, the internal pressure of the inflator may rise abnormally when the airbag deploys, which can rupture the inflator housing, causing fragments to scatter and posing a risk of injury to the occupant.
In the engine fuel system, some pulsation dampers (fuel pressure pulsation attenuators) were manufactured with their diaphragms damaged during the production process. If they continue to be used in this condition, the fuel pressure pulsations that occur during vehicle operation may cause cracks to develop from the damage in the diaphragm, which could result in fuel leakage.
In the manufacturing process of the oil cooler hoses for continuously variable transmissions (CVT), some hoses have been subjected to improper cleaning treatment. As a result, the hose may come off due to engine vibration and other factors, causing oil to leak, which can render the vehicle unable to travel and, in the worst case, lead to a fire.
There are some units in which the switch unit for operating the turn signals and other functions, located below the steering wheel, has been installed out of its proper position. As a result, when the steering wheel is operated, the electrical wiring of that switch unit may come loose, and in the worst case, a short circuit could occur and lead to a fire.
In the front seats, the mounting bolts were not tightened properly, so some of these bolts may loosen due to vibration during driving. As a result, abnormal noise may occur from the mounting area, and if use continues as is, the bolts may fall out. In the worst case, the seat could move in a collision, and the occupant protection performance it is meant to provide may not be achieved.
In the fuel pump impeller (resin impeller), improper molding conditions can result in low resin density, causing the impeller to swell and deform when exposed to fuel. As a result, the impeller may come into contact with the pump case, causing the fuel pump to malfunction and, in the worst case, potentially leading to engine stall while driving.
For replacement front seat belt retractors, some units were assembled with defective force limiter mechanisms that were manufactured improperly. Therefore, in the event of a collision or similar situation, the force limiter may not function correctly, causing the seat belt to be pulled out, and there is a risk that the occupant protection performance required by regulations may not be met.
In the fuel pump impeller (resin impeller), improper molding conditions can lead to low resin density, causing the impeller to swell and deform when exposed to fuel. As a result, the impeller may come into contact with the pump case, causing the fuel pump to malfunction and, in the worst case, potentially leading to engine stalling while driving.
De airbag inflators zijn vervaardigd zonder de juiste afdichtingen waardoor lucht en vocht gedurende een langere periode in de inflators kunnen lekken. Hierdoor gaat de kwaliteit het drijfgas achteruit.
rdwMar 4, 2020MGP200090Model years 2012Shown in the original Dutch · translation pendingView details →
In a continuously variable transmission (CVT) torque converter, improper manufacture of the internal bearing leaves unevenness on the sliding surface. During use, this unevenness can cause the bearing to wear abnormally and break. Fragments of the bearing then scatter inside the torque converter and produce abnormal noise. If the vehicle continues to be driven in this condition, the fragments may, in the worst case, become lodged inside the torque converter, causing the engine to stall when the vehicle stops and preventing it from moving off again.
Sources: NHTSA (United States, public domain), Transport Canada (Open Government Licence – Canada), DVSA (United Kingdom, Open Government Licence v3.0), RappelConso and EU Safety Gate (France, Licence Ouverte 2.0), Japan's MLIT (Public Data License 1.0) and South Korea's MOLIT (car.go.kr).