Service bulletins (TSBs) are repair instructions manufacturers send to their dealers about known problems. They are not safety recalls, but they often confirm a defect.
Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): **P0420 - Catalyst System Efficiency Below Threshold Bank 1. P0430 - Catalyst System Efficiency Below Threshold Bank 2.** P0456 - EVAP System Small Leak. **Customers may also comment on one or more of the following: Vehicle fails emissions inspection testing.* This bulletin involves reprogramming the PCM with the latest available software.
NHTSA · manufacturer bulletin11034362Model years 2019View details →
Part Description: Mirror, Side View Issue Description: New mirror now includes a grommet on the electrical wire. If the mirror being removed from the vehicle does not have a grommet and the new mirror does, this is not an issue. Install the new mirror and grommet.
NHTSA · manufacturer bulletin10229874Model years 2014View details →
Part Description: 5.7L Long Block Issue Description: This 5.7L Long Block Assembly is compatible with both EGR and Non-EGR applications. An EGR Block-Off Plate (53032739AA) must be ordered when installing this Long Block Assembly in a Non-EGR application. Unless, the EGR Block-Off Plate is being transferred from the old engine.
NHTSA · manufacturer bulletin10229181Model years 2007View details →
Customer Satisfaction Notification T12 VECI Label The Vehicle Emission Control Information (VECI) label on about 120,000 of the above vehicles may be missing emission control information. The VECI label is often used during in-use Inspection and Maintenance (I/M) testing to verify proper emissions related components. Incorrect VECI label information could result in denial of vehicle registration for the vehicle in the state of California. A new VECI label must be installed.
NHTSA · manufacturer bulletin10224875Model years 2015View details →
Service - Four Piece Oil Pan Gasket All Cummins Equipped Vehicles ONLY - The replacement oil pan gasket can be a four piece gasket rather than a single piece gasket. This applies to Cummins 5.9L and 6.7L engines only. Installation: 1. Clean the oil pan T-joints.~ 2. Fill the T-joint between the pan rail/gear housing and pan rail/rear seal retainer with sealant. Use Mopar Silicone Rubber Adhesive Sealant or equivalent. 3. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the oil pan flange.~ 4. The four piece gasket will need to be assembled to make a complete oil pan gasket. 5. Lay the oil pan gasket(s) onto the oil pan flange.~ 6. Ensure the oil pan gasket segment joints are properly aligned. 7. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the top of the oil pan gasket.~ 8. Install the oil pan. Starting from the center and working outward, tighten the oil pan bolts to 28 Nm [21 ft. lbs.].
NHTSA · manufacturer bulletin10223854Model years 2007View details →
Part Description: 5.7L Long Block Issue Description: This 5.7L Long Block Assembly is compatible with both EGR and Non-EGR applications. An EGR Block-Off Plate (53032739AA) must be ordered when installing this Long Block Assembly in a Non-EGR application. Unless, the EGR Block-Off Plate is being transferred from the old engine.
NHTSA · manufacturer bulletin10223602Model years 2007View details →
Part Description: Mirror, Side View Issue Description: New mirror now includes a grommet on the electrical wire. If the mirror being removed from the vehicle does not have a grommet and the new mirror does, this is not an issue. Install the new mirror and grommet.
NHTSA · manufacturer bulletin10221042Model years 2014View details →
SEAL, Input If looking to replace stubshaft due to ATX fluid leaking, do not replace PTU seals. None of the seals from the PTU side will need to be replaced whenever the ATX stubshaftis replaced, even though V-seal (68408748A$) is in direct contact with the stubshaft,it will not avoid grease/oil leakage from transmission side. PTU V-seals are intended to act as a dust cover for stubshaft-PTU input shaft spline interface. PTU Input shaft seal (68408749A$) is intended to hold PTU oil and debris ingress; it should be replaced only if the fluid leakage is confirmed to be PTU oil and not ATX trans. fluid.
NHTSA · manufacturer bulletin10168388Model years 2019View details →
Part Description: Mirror, Side View Issue Description: New mirror now includes a grommet on the electrical wire. If the mirror being removed from the vehicle does not have a grommet and the new mirror does, this is not an issue. Install the new mirror and grommet.
NHTSA · manufacturer bulletin10139872Model years 2014View details →
Radiator If vehicle comes in for transmission fluid leaking from trans-oil cooler fittings on the radiator, please check the following before replacing the radiator/cooler:~ 1. Remove both of the transmission lines from the cooler?s top/bottom flared fittings on the radiator. ~ 2. Loosen the hex nut on the top flared fitting on the radiator tank.~ 3. Torque the top flared fitting to 235 +/- 15 Lb-In.~ 4. Torque hex nut to 100 +/- 10 Lb-In.~ 5. Repeat for bottom flared fitting.~ 6. Reinstall transmission line per normal installation procedures and ensure correct fluid level.~ ~ If vehicle is in need of a new radiator for another reason, check the new radiator for correct torque on the trans-oil cooler fitting per steps 2-5 above.~ ~ If radiator has a yellow mark by the trans-oil cooler fittings the torque does not have to be checked.
NHTSA · manufacturer bulletin10121923Model years 2000View details →
Oem torque specifications for the steering shaft have been identified and are now being used in the installation of the vmi steering extension. This sb notifies the technicians to ensure the torque specifications for the steering extension have been complied with at the factory. This will bring the van into conformance with vmi updated processes
NHTSA · manufacturer bulletin10096410Model years 2016View details →
Oem torque specifications for the steering shaft have been identified and are now being used in the installation of the vmi steering extension. This sb notifies the technicians to ensure the torque specifications for the steering extension have been complied with at the factory. This will bring the van into conformance with vmi updated processes
NHTSA · manufacturer bulletin10084322Model years 2016View details →
"flash: Powertrain diagnostic and system improvements this bulletin involves selectively erasing and reprogramming the powertrain control module (pcm) with new software. Symptom/condition: A small number of customers may experience a malfunction indicator lamp (mil) illumination. Upon further investigation the technician may find one or more of the following diagnostic trouble codes (dtcs) set in the pcm: Jc vehicles 3.6l: P0335 - crankshaft position sensor circuit. P2610 - pcm internal engine off timer performance. U0140 - lost communication with body control module (bcm). P0456 - evap system small leak. P0108 - manifold absolute pressure sensor circuit high (2012 my only). The following transmission enhancements are also included in this software update: Continuous cycling of fuel pump relay when using remote start. 1 - 2 upshift clunk or bump. 3 - 4 harsh upshift at closed throttle after a wot stab in 1st or 2nd gear. 4 - 5 upshift clunk or bump. 5 - 6 upshift clunk or bump. 5- 4 downshift clunk or bump. 6 - 5 downshift clunk or bump. Rpm fluctuating or jerking while operating in cruise control. Condition is more noticeable when the vehicle is going up and down grades. Improves the consistency of how shifts are controlled during upshifts torque management. Delayed downshifts. Jc vehicles 2.4l: **u0140 - lost communication with body control module (bcm).** p0456 - evap system small leak. The following transmission enhancements are also included in this software update: 1 - 2 upshift clunk or bump. 3 - 4 harsh upshift at closed throttle after a wot stab in 1st or 2nd gear. 4 - 5 upshift clunk or bump. Rpm fluctuating or jerking while operating in cruise control. Condition is more noticeable when the vehicle is going up and down grades. 1 - 2 harsh upshift going down a grade. 3 - 2 downshift clunk or bump. 4 - 3 downshift clunk or bump.
NHTSA · manufacturer bulletin10076532Model years 2013View details →
Chrysler/dodge: When braking, steering wheel would shake, brake pedal pulsates and/or floor pan vibrates and need to replace, both, front brake rotors, right and left front lower control arms, brake linings and resurfacing, and install new right and left front lower control arms. Model 2011-2012 caravan, town and country. *pe
NHTSA · manufacturer bulletin10054185Model years 2012View details →
Chrysler/dodge service campaign: See document search button for owner letter. The low pressure power steering hose on certain vehicles may leak under certain extreme cold climate operating conditions. This result in a loss of power steering assist upon vehicle start up. Csc letter was received. *pe
NHTSA · manufacturer bulletin10028064Model years 2008View details →
Chrysler\dodge\jeep service campaign: See document search button for owner letter. Emissions recall h06-spark plugs. Approximately 440 engines in the above vehicles may have had incorrect spark plugs inadvertently installed in three of the six cylinders. Csc was received. *pe
NHTSA · manufacturer bulletin10025305Model years 2008View details →
Sources: NHTSA (United States, public domain), Transport Canada (Open Government Licence – Canada), DVSA (United Kingdom, Open Government Licence v3.0), RappelConso and EU Safety Gate (France, Licence Ouverte 2.0), Japan's MLIT (Public Data License 1.0) and South Korea's MOLIT (car.go.kr).