Due to a non-conformity in the production process the electrical power steering (EPS) must be replaced. This will prevent a potential loss of steering assistance. Loss of EPS functionality could increase the risk of a collision occurring.
DVSA · United KingdomDec 19, 2017R/2017/297Model years 2017View details →
Enkele veiligheidsgordelsluitingen op de voorstoelen hebben bij fabricage niet de juiste warmtebehandeling ondergaan. Hierdoor zijn de sluitingen niet van voldoende sterkte.
rdwMar 4, 2015MGP150078Model years 2015Shown in the original Dutch · translation pendingView details →
The fuel pump protection bracket is not to conformity and in the event of an accident the fuel feed pipe could be damaged leading to an increased risk of fuel leakage and possible fire.
DVSA · United KingdomJan 5, 2014R/2013/130Model years 2013View details →
The steering column upper shaft fixing bolt may not have had thread locking agent applied to it during assembly. This may allow it to come loose causing a noise. In extreme cases this may result in a loss of steering control.
DVSA · United KingdomSep 10, 2010R/2010/101View details →
In the power transmission system, some right front drive shafts have been fitted with components of insufficient strength due to improper manufacturing control. As a result, the shaft may break during use, potentially rendering the vehicle unable to be driven.
It has been identified that the rear brake shoe lining material may not have been manufactured to the correct specification. This could result in a reduction in brake performance from the rear brakes.
DVSA · United KingdomNov 25, 2016R/2016/247Model years 2016View details →
The seat may not remain in position when subjected to greater than normal driving forces such as those involved in an impact. This may possibly cause injury to the driver/passenger seated in the right hand front seat. The right hand front seat guides may not conform to design specification and installation specifications.
DVSA · United KingdomSep 23, 2016R/2016/194Model years 2015–2016View details →
De diagnosesoftware in de Power Inverter Module (PIM) is te gevoelig. Tijdens normaal gebruik van de auto kan de module ten onrechte de diagnose van een overspanning conditie instellen.
rdwSep 2, 2016MGP160342Model years 2014–2016Shown in the original Dutch · translation pendingView details →
It has been identified that the front seatbelt anchorage links may not have been manufactured to the correct specification. If the link is subjected to an abnormal force then it may not perform as required.
DVSA · United KingdomApr 10, 2015R/2015/077Model years 2014View details →
It has been identified that the front seatbelt anchorage links may not have been manufactured to the correct specification. If the link is subjected to an abnormal force then it may not perform as required.
DVSA · United KingdomApr 10, 2015R/2015/076Model years 2014View details →
It is possible under extreme conditions that the wiring harness under the dashboard could come into contact with the steering column. This over a period of time may result in the chaffing of wires in the harness. If this should occur then it is possible both the exterior and instrument lights could fail.
DVSA · United KingdomSep 22, 2014R/2014/089Model years 2013–2014View details →
It is possible under extreme conditions that the wiring harness under the dashboard could come into contact with the steering column. This over a period of time may result in the chaffing of wires in the harness. If this should occur then it is possible both the exterior and instrument lights could fail.
DVSA · United KingdomSep 22, 2014R/2014/088Model years 2013–2014View details →
Sources: NHTSA (United States, public domain), Transport Canada (Open Government Licence – Canada), DVSA (United Kingdom, Open Government Licence v3.0), RappelConso and EU Safety Gate (France, Licence Ouverte 2.0), Japan's MLIT (Public Data License 1.0) and South Korea's MOLIT (car.go.kr).