Service bulletins (TSBs) are repair instructions manufacturers send to their dealers about known problems. They are not safety recalls, but they often confirm a defect.
Flash: Drivetrain Control Module (DTCM) Updates Customers may experience a Malfunction Indicator Lamp (MIL) or warning lamp illumination. Upon further investigation the technician may find that the multiple Diagnostic Trouble Codes (DTCs) have been set: ? C1403-29 - Transfer Case Range Position Sensor-Signal Invalid. ? C14AA-62 - Transfer Case Motor Position Sensor Supply-Signal Compare Failure. This bulletin involves reprogramming the DTCM with the latest software available.
NHTSA · manufacturer bulletin10239927Model years 2023View details →
Part Description: 5.7L Long Block Issue Description: This 5.7L Long Block Assembly is compatible with both EGR and Non-EGR applications. An EGR Block-Off Plate (53032739AA) must be ordered when installing this Long Block Assembly in a Non-EGR application. Unless, the EGR Block-Off Plate is being transferred from the old engine.
NHTSA · manufacturer bulletin10229181Model years 2006View details →
UConnect Hands Free Module Fails To Respond Due To Module Lock Up This bulletin involves replacing the Hands Free Module (HFM) if required. The HFM fails to operate causing the UConnect Hands Free Communications system to not respond when system activation is attempted by the customer. Further diagnosis may reveal that when the wiTECH scan tool is used to read Diagnostic Trouble Codes (DTCs) the tool indicates that the module is not responding. Other modules on the bus may display loss of communication with the HFM. If the Hands Free Communication system is unresponsive then the HFM may require electronic reset.To perform a electronic reset, turn off the vehicle and pull the Ignition Off Drain (IOD) fuse. Wait a few minutes before reinstalling the IOD fuse and checking if the HFM is communicating. If the HFM still will not communicate, then normal No Response diagnostic should be performed. If the HFM is working properly, the module should be replaced to prevent this condition from happening again.
NHTSA · manufacturer bulletin10139704Model years 2006View details →
"Rear View Camera (RVC) Error Customers may experience the following: RVC display has a blurry image, a blue screen and/or grid line that is not working Fig. 1. This bulletin involves inspecting the RVC for errors and possibly replacing the RVC."
NHTSA · manufacturer bulletin11001287Model years 2024View details →
"Rear View Camera (RVC) Error Customers may experience the following: RVC display has a blurry image, a blue screen and/or grid line that is not working Fig. 1. This bulletin involves inspecting the RVC for errors and possibly replacing the RVC."
NHTSA · manufacturer bulletin11001235Model years 2024View details →
"Rear View Camera (RVC) Error Customers may experience the following: RVC display has a blurry image, a blue screen and/or grid line that is not working Fig. 1. This bulletin involves inspecting the RVC for errors and possibly replacing the RVC."
NHTSA · manufacturer bulletin11001135Model years 2024View details →
Flash: Body Control Module (BCM) Updates Customers may experience the following: ? **During an Engine Stop/Start (ESS) event, media source is changed from USB to AM/FM.** ? Excessive consistent battery drain. ? Rear tail lamps flickering. Upon further investigation the technician may find that the following Diagnostic Trouble Code (DTC) has been set: ? B100B-15 - Left Rear Mobile Lantern Position Light Command - Short - Battery Circuit Or Open Circuit. This bulletin involves reprogramming the BCM module with the latest available software.
NHTSA · manufacturer bulletin10248043Model years 2022View details →
Flash: Body Control Module (BCM) Updates Customers may experience the following: ? During an Engine Stop/Start (ESS) event, media source is changed from USB to AM/FM. This bulletin involves reprogramming the BCM module with the latest available software.
NHTSA · manufacturer bulletin10248044Model years 2023View details →
B2768-49 Right Impact Pressure Sensor-Internal Failure, prior to replacement of any components please contact FCA Redacted Content for further assistance. If no response in 15 minutes, proceed with repair.
NHTSA · manufacturer bulletin10240000Model years 2023View details →
Flash: Body Control Module (BCM) Updates Customers may experience the following: ? **During an Engine Stop/Start (ESS) event, media source is changed from USB to AM/FM.** ? Excessive consistent battery drain. ? Rear tail lamps flickering. Upon further investigation the technician may find that the following Diagnostic Trouble Code (DTC) has been set: ? B100B-15 - Left Rear Mobile Lantern Position Light Command - Short - Battery Circuit Or Open Circuit. This bulletin involves reprogramming the BCM module with the latest available software.
NHTSA · manufacturer bulletin10234516Model years 2022View details →
Flash: Body Control Module (BCM) Updates Customers may experience the following: ? During an Engine Stop/Start (ESS) event, media source is changed from USB to AM/FM. This bulletin involves reprogramming the BCM module with the latest available software.
NHTSA · manufacturer bulletin10234517Model years 2023View details →
KEY, Master If replacing the key/FOBIK on a WJ, KJ, TJ, or PT Cruiser, use the "AC" NIC level part number. The "AB" NIC level will not program to these platforms. For all other platforms, if the "AB" NIC level will not program to the vehicle, use the "AC" NIC level part and submit a part warranty.
NHTSA · manufacturer bulletin10229256Model years 2006View details →
Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.
NHTSA · manufacturer bulletin10220840Model years 2005View details →
Sources: NHTSA (United States, public domain), Transport Canada (Open Government Licence – Canada), DVSA (United Kingdom, Open Government Licence v3.0), RappelConso and EU Safety Gate (France, Licence Ouverte 2.0), Japan's MLIT (Public Data License 1.0) and South Korea's MOLIT (car.go.kr).