Free to read · free account to contributeSuccessor to Anticars (2000)

Mazda Tribute

2000–2011 · 2 generations · 19 documented defects · 4 markets
Generations

Service bulletins (TSBs) are repair instructions manufacturers send to their dealers about known problems. They are not safety recalls, but they often confirm a defect.

Model year
MarketAllEUNAUK
Tribute II · 2007–2011
BulletinCriticalEngineNA

Bulletin

On some vehicles, a sulfur smell or 'rotten egg' odor may be noticed coming from the exhaust system. The odor is usually noticed after a cold start, fast idle, extended periods of idling and full throttle acceleration. Sulfur smell is not an indication of an engine concern and will not cause reduced driveability or durability of the engine or any of its emission components. The sulfur smell or 'rotten egg' odor is caused by high amounts of sulfur in the gasoline being used in the vehicle. Sulfur is normally eliminated during the refining process, but the EPA regulation of sulfur in gasoline differs from state to state. Vehicles using fuel containing high amounts of sulfur will most likely emit sulfur smell from the exhaust system.When high sulfur fuel is burned, there is a chemical reaction in the catalytic converter causing the sulfur tooxidize. As the vehicle is driven, the oxidizing reaction odor in the converter will decrease with mileage and age.

NHTSA · manufacturer bulletin10153311Model years 2011View details →
Tribute II · 2007–2011
BulletinCriticalEngineNA

Bulletin

On some vehicles, a sulfur smell or 'rotten egg' odor may be noticed coming from the exhaust system. The odor is usually noticed after a cold start, fast idle, extended periods of idling and full throttle acceleration. Sulfur smell is not an indication of an engine concern and will not cause reduced driveability or durability of the engine or any of its emission components. The sulfur smell or 'rotten egg' odor is caused by high amounts of sulfur in the gasoline being used in the vehicle. Sulfur is normally eliminated during the refining process, but the EPA regulation of sulfur in gasoline differs from state to state. Vehicles using fuel containing high amounts of sulfur will most likely emit sulfur smell from the exhaust system. When high sulfur fuel is burned, there is a chemical reaction in the catalytic converter causing the sulfur to oxidize. As the vehicle is driven, the oxidizing reaction odor in the converter will decrease with mileage and age.

NHTSA · manufacturer bulletin10145242Model years 2011View details →
Tribute II · 2007–2011
BulletinModerateOtherNA

Bulletin

In support of the new MRT distribution, Mazda will ship to dealers a new Dual Purpose Diagnostic Leak Detector beginning March, 2019. Training videos will be posted to MGSS shortly and Workshop Manual procedures will be revised gradually.

NHTSA · manufacturer bulletin10154879Model years 2011View details →
Tribute II · 2007–2011
BulletinModerateSuspensionNA

Bulletin

If a vehicle has body vibration or steering wheel shimmy while driving and the root cause is determined to be tire balance, re-balance the tires using a Hunter GSP9700 or equivalent balance machine. If your dealer does not have a GSP9700 or equivalent balance machine, sublet the vehicle out for repair. To find the location of a GSP9700 near your dealer, visit Hunter?s web site at www.gsp9700.com and click on ?Locate a GSP9700 Road Force Balancer.?

NHTSA · manufacturer bulletin10154139Model years 2011View details →
Tribute II · 2007–2011
BulletinModerateOtherNA

Bulletin

This service bulletin provides information regarding the proper use of the driver's floor mat to avoid anypotential interference with the foot pedals. The following are possible causes of floor mat interference,which can be avoided with proper usage. Floor mat moves forward due to improper installation. Inappropriate floor mat (such as aftermarket, non-factory-equipped, or non-genuine) is used. Floor mat is stacked one on top of another.

NHTSA · manufacturer bulletin10153331Model years 2011View details →
Tribute II · 2007–2011
BulletinModerateSuspensionNA

Bulletin

Some customers may complain that the steering wheel is off center more than 3 even when driving straight on a flat road.

NHTSA · manufacturer bulletin10153318Model years 2011View details →
Tribute II · 2007–2011
BulletinModerateBrakesNA

Bulletin

Mazda North American Operations has approved an additional on-car brake lathe as an option for MNAO authorized equipment. The Pro-Cut On-Car Brake Lathe has been added to the MNAO authorized equipment program. NOTE: Accu-turn is still an approved brake lathe, but it is no longer available for purchase from our vendor. IMPORTANT: Rotors must be machined using a Mazda approved on-car brake lathe, or warranty claims are subject to denial or debit. Tool Number Description Pricing PC1923MAZ Pro-Cut On-Car Brake Lathe Check eStore or call for current pricing OBTAINING TOOLS This tool can be ordered through Mazda eStore. You can log on to eStore at: http://dealers.mazdausa.com CUSTOMER SERVICE INFORMATION For warranty or product information contact Mazda Authorized Service Equipment at 877-768-6657. Customer service representatives are available from 7:30 AM until 7:00 PM CST, Monday through Friday. SPECIAL SERVICE TOOL (SST) PART NAME: OVERVIEW Pro-Cut On-Car Brake Lathe PART NUMBER: PC1923MAZ APPLICABLE MODELS: All USAGE: To machine brake rotors on the vehicle.

NHTSA · manufacturer bulletin10153307Model years 2011View details →
Tribute II · 2007–2011
BulletinModerateBrakesNA

Bulletin

Mazda North American Operations has approved an additional on-car brake lathe as an option for MNAO authorized equipment. The Pro-Cut On-Car Brake Lathe has been added to the MNAO authorized equipment program. NOTE: Accu-turn is still an approved brake lathe, but it is no longer available for purchase from our vendor. IMPORTANT: Rotors must be machined using a Mazda approved on-car brake lathe, or warranty claims are subject to denial or debit.

NHTSA · manufacturer bulletin10148003Model years 2011View details →
Tribute II · 2007–2011
BulletinModerateBrakesNA

Bulletin

Mazda North American Operations has approved an additional on-car brake lathe as an option for MNAOauthorized equipment. The Pro-Cut On-Car Brake Lathe has been added to the MNAO authorizedequipment program.NOTE: Accu-turn is still an approved brake lathe, but it is no longer available for purchase from our vendor. IMPORTANT: Rotors must be machined using a Mazda approved on-car brake lathe, or warranty claimsare subject to denial or debit.

NHTSA · manufacturer bulletin10142515Model years 2011View details →
Tribute II · 2007–2011
BulletinModerateSuspensionNA

Bulletin

Some customers may complain that the steering wheel is off center more than 3 even when driving straight on a flat road.

NHTSA · manufacturer bulletin10142519Model years 2011View details →
Tribute II · 2007–2011
BulletinModerateOtherNA

Bulletin

This service bulletin provides information regarding the proper use of the driver's floor mat to avoid any potential interference with the foot pedals. The following are possible causes of floor mat interference, which can be avoided with proper usage. Floor mat moves forward due to improper installation. Inappropriate floor mat (such as aftermarket, non-factory-equipped, or non-genuine) is used. Floor mat is stacked one on top of another. Use these points at your dealership to protect our mutual operations and to help ensure our customers' safety.

NHTSA · manufacturer bulletin10134703Model years 2011View details →
Tribute II · 2007–2011
BulletinModerateBodyNA

Bulletin

When dealing with customer complaints of excessive condensation and/or water within the headlamp unit, first determine if all the bulb sockets (including O-ring), seals and covers are present and correctly installed. In most cases you will find that the Bulb Seal No. 1 (A) or HID Bulb Seal No. 1 (B) and Bulb Seal No. 2 (C) socket covers have not been correctly installed or are missing due to improper prior repairs (i.e., customer replacing the headlamp bulbs or body shop not transferring them when replacing the headlamp unit(s) due to a collision). Any damage caused by missing socket covers, HID module seal (D), or missing bumper brackets (E) is not covered by warranty policy.

NHTSA · manufacturer bulletin10118468Model years 2011View details →
Tribute II · 2007–2011
BulletinModerateBrakesNA

Bulletin

Mazda Motor Corporation has decided to conduct a Special Service Program (SSP) on certain 2009-2011 Tribute vehicles. On certain 2009-2011 Tribute vehicles, contamination on the internal motor contacts of the throttle body may result in intermittent electrical connectivity.If this condition is present, the Malfunction Indicator Lamp or Wrench Lamp will illuminate, and the vehicle may enter fail-safe mode. In this mode, the engine power and vehicle speed is reduced, while maintaining full functionality of the power steering, power braking, lighting, and climate control systems. To improve vehicle performance should the above problem occur, dealers must reprogram the Powertrain Control Module (PCM). Please refer to Attachment II for repair details.This SSP will be in effect until July 31, 2015 regardless of mileage.

NHTSA · manufacturer bulletin10117770Model years 2011View details →
Tribute II · 2007–2011
BulletinModerateBrakesNA

Bulletin

Mazda Motor Corporation is extending the warranty coverage for throttle body replacement on certain 2009-2011 Tribute vehicles produced from April 14, 2008 through May 30, 2011. The warranty for throttle body replacement will be extended to 10 years (120 months) from the original warranty start date or 150,000 miles, whichever comes first. If a vehicle has already exceeded the time or mileage limits, this coverage will last through January 31, 2015. Affected vehicles may develop contamination on the internal motor contacts of the throttle body, resulting in intermittent electrical connectivity. If this condition is present, the Malfunction Indicator Lamp (MIL) or Wrench light will illuminate and the vehicle may enter a fail-safe mode. In this mode, engine power and vehicle speed are reduced, while full functionality of the power steering, power braking, lighting, and climate control systems are maintained. If diagnosis identifies the throttle body as the causal component, dealers are authorized to replace the throttle body under this warranty extension program.This service must be performed at no charge to the vehicle owner.

NHTSA · manufacturer bulletin10117771Model years 2011View details →
Tribute II · 2007–2011
BulletinModerateBodyNA

Bulletin

When dealing with customer complaints of excessive condensation and/or water within the headlamp unit, first determine if all the bulb sockets are resent and correctly installed. In most cases you will find that the bulb seal no. 1 (a) or hid bulb seal no. 1 (b) and bulb seal no. 2 (c) socket overs have not been correctly installed or are missing due to improper prior repairs (i.E., customer replacing the headlamp bulbs or body shop not transferring them when replacing the headlamp unit(s) due to a collision). Any damage caused by missing socket covers, hid module seal (d), or missing bumper brackets (e) is not covered by warranty policy.

NHTSA · manufacturer bulletin10105886Model years 2011View details →
Tribute II · 2007–2011
BulletinModerateSuspensionNA

Bulletin

Some customers may complain that the steering wheel is off center more than 3 even when driving straight on a flat road.

NHTSA · manufacturer bulletin10101062Model years 2011View details →
Tribute II · 2007–2011
BulletinModerateBodyNA

Bulletin

When dealing with customer complaints of excessive condensation and/or water within the headlamp unit, first determine if all the bulb sockets are present and correctly installed. In most cases you will find that the bulb seal no. 1 (a) or hid bulb seal no. 1 (b) and bulb seal no. 2 (c) socket covers have not been correctly installed or are missing due to improper prior repairs (i.E., customer replacing the headlamp bulbs or body shop not transferring them when replacing the headlamp unit(s) due to a collision). Any damage caused by missing socket covers, hid module seal (d), or missing bumper brackets (e) is not covered by warranty policy.

NHTSA · manufacturer bulletin10098885Model years 2011View details →
Tribute II · 2007–2011
BulletinModerateSuspensionNA

Bulletin

Bulletin noteservice bulletin 06-001/14, 2008-2011 tribute - dtc b2278 stored in the power steering control module, is no longer valid. Service bulletin 06-001/14 has been superseded by safety recall 7614e, 2008-2011 tribute - electric power-assisted steering (epas).

NHTSA · manufacturer bulletin10098346Model years 2011View details →
Tribute II · 2007–2011
BulletinModerateOtherNA

Bulletin

This service bulletin provides information regarding the proper use of the drivers floor mat to avoid any potential interference with the foot pedals. The following are possible causes of floor mat interference, which can be avoided with proper usage. Floor mat moves forward due to improper installation. Inappropriate floor mat (such as aftermarket, non-factory-equipped, or non-genuine) is used. Floor mat is stacked one on top of another.

NHTSA · manufacturer bulletin10098282Model years 2011View details →
Tribute II · 2007–2011
BulletinModerateBrakesNA

Bulletin

Mazda north american operations received many requests from our dealers asking us to approve additional on-car brake lathes as an option for mnao authorized equipment. Due to your feedback and after evaluating a few on-car brake lathes, we are pleased to announce that we have added the pro cut on-car brake lathe to mnao authorized equipment program. The accu-turn is still an approved brake lathe but it is no longer available for purchase from our vendor. Important reminder rotors must be machined using a mazda approved on-car brake lathe or warranty claims are subject to denial or debit.

NHTSA · manufacturer bulletin10098245Model years 2011View details →
Tribute II · 2007–2011
BulletinModerateOtherNA

Bulletin

Some vehicles may exhibit an intermittent no crank, no start condition with no diagnostic trouble codes (dtc) or passive anti-theft system (pats) indicator flashing.

NHTSA · manufacturer bulletin10097806Model years 2010–2011View details →
Tribute II · 2007–2011
BulletinModerateGearboxNA

Bulletin

Some vehicles equipped with an automatic transmission gain enhanced flat tow performance with an optional transmission cooling pump kit for recreational towing. The kit is available from the parts department and will help prevent transmission overheating.

NHTSA · manufacturer bulletin10097804Model years 2011View details →
Tribute II · 2007–2011
BulletinModerateGearboxNA

Bulletin

Some vehicles may exhibit an occasional fluid leak coming from the rear differential vent cap in temperatures below 32 degrees fahrenheit (0 degrees celsius) under certain conditions.

NHTSA · manufacturer bulletin10097801Model years 2011View details →
Tribute II · 2007–2011
BulletinModerateSuspensionNA

Bulletin

Some customers may complain that the steering wheel is off center more than 3 even when driving straight on a flat road.

NHTSA · manufacturer bulletin10097722Model years 2011View details →
Tribute II · 2007–2011
BulletinModerateSuspensionNA

Bulletin

Some customers may complain that the steering wheel is off center more than 3 even when driving straight on a flat road.

NHTSA · manufacturer bulletin10097377Model years 2011View details →
Older →

Sources: NHTSA (United States, public domain), Transport Canada (Open Government Licence – Canada), DVSA (United Kingdom, Open Government Licence v3.0), RappelConso and EU Safety Gate (France, Licence Ouverte 2.0), Japan's MLIT (Public Data License 1.0) and South Korea's MOLIT (car.go.kr).