On certain 318I, 318IC, 318IS, 325IC, 325IS, 325IX, 525I, 535I, 735I and 735IL vehicles, the fuel feed hose could harden and "set" over time due to engine compartment temperatures. If this "setting" occurs, it is possible that seepage between the hose and fitting could result because the clamp cannot provide sufficient sealing force to compensate for the hardening of the hose. Fuel seepage, in the presence of an ignition source, could result in an engine compartment fire. Correction: fuel feed hoses and associated clamps will be replaced with ones of a new design.
Transport Canada30 may 19941994096Años modelo 1989Mostrado en inglés original · traducción pendienteVer detalles →
Feed fuel hoses can harden and "set" over time, allowing a seepage of fuel at the connection between the hose and the engine fitting. The clamp used to hold the hose to the fitting is unable to compensate for the hardening of the feed fuel hose.
NHTSA · Estados Unidos11 abr 199494V066000Años modelo 1989Mostrado en inglés original · traducción pendienteVer detalles →
La avería o el fallo de un componente del sistema de refrigerante provoca un aumento significativo de la temperatura del refrigerante y, como consecuencia, un aumento de la presión del sistema.
NHTSA · Estados Unidos1 feb 199393V015000Años modelo 1984–1989Traducido automáticamente · original: inglésVer detalles →
On certain 318I vehicles, under certain conditions, the interior heater water control valve may bind while closing. This binding or slow-closing condition may cause the valve solenoid to draw excessive current, possibly resulting in overheating of the valve connector wiring and insulation. This condition could result in a passenger compartment fire.
Transport Canada24 sept 19841984105Años modelo 1984Mostrado en inglés original · traducción pendienteVer detalles →
On certain 318I, 325I and M3 vehicles, elevated pressure in the cooling system due to overheating could result in cracking of the heater core end piece. Should this happen, coolant could be expelled onto the lower right leg of the driver, possibly resulting in personal injury and/or fogging of the interior surfaces of the windows causing reduced driver vision. Correction: A thermistatic bypass valve will be installed to control coolant temperature in the heater core. Also, a new design radiator cap will be installed to control pressure and provide greater overflow.
Transport Canada19 jul 19931993100Años modelo 1984–1989Mostrado en inglés original · traducción pendienteVer detalles →
On certain 325IX vehicles, the oil dipstick tube attaching bracket may have been bent during the manufacturing process or during scheduled maintenance. This could possibly cause the dipstick to interfere with the throttle bellcrank lever's range of motion and prevent the lever from returning to the idle position after release of the accelerator pedal. Correction: Throttle bellcrank lever will be modified to provide sufficient clearance. Note: Vehicles with manual transmission only.
Transport Canada6 abr 19881988049Años modelo 1988Mostrado en inglés original · traducción pendienteVer detalles →
The oil dipstick tube attaching bracket may have been bent during production or scheduled maintenance, reducing the clearance between the dipstick ring and the throttle bellcrank lever.
NHTSA · Estados Unidos15 mar 198888V031000Años modelo 1988Mostrado en inglés original · traducción pendienteVer detalles →
On certain 325E, 325ES, 528E, 535I, 635CSI and 735I vehicles, the center high mounted brake light could add sufficient electrical load to cause the brake light switch to overheat, eventually leading to melting of the plastic internal switch parts. This could cause the switch plunger to jam in the ON or OFF position. This would render the brake light permanently ON or OFF regardless of brake pedal operation. Correction: A brake light switch with an increased current load capacity will be installed on affected vehicles.
Transport Canada27 nov 19861986134Años modelo 1986–1987Mostrado en inglés original · traducción pendienteVer detalles →
On certain 318I, 325, 325E and 325ES vehicles, when a significant force is applied directly to the steering gearbox as the result of certain frontal crash conditions or front end contact with an object on the road, the steering column disengagement element, which is designed to reduce the amount of steering wheel rearward travel, could disengage completely. This would result in loss of post impact steering maneuverability without prior warning. Correction: Two plates will be bolted to the disengagement element to ensure that the element will not completely disengage in the event of an impact to the steering gear.
Transport Canada22 oct 19861986117Años modelo 1984–1986Mostrado en inglés original · traducción pendienteVer detalles →
The two parts of the steering column disengagement element could completely disconnect if the car contacts an object in the roadway or elsewhere of sufficient mass to apply a significant force directly to the steering gearbox. Consequence of defect: Steering control would be lost.
NHTSA · Estados Unidos20 oct 198686V138000Años modelo 1985–1986Mostrado en inglés original · traducción pendienteVer detalles →
The idle control valve which controls idle speed by varying the amount of intake air that bypasses the throttle plate is subject to backfire into the intake manifold. Such backfire can damage the valve and cause the idle valve plate to remain open. Consequence of defect: This will result in abnormally high idle speed.
NHTSA · Estados Unidos6 may 198585V058000Años modelo 1984Mostrado en inglés original · traducción pendienteVer detalles →
Water control valve in the heating system may not close completely. Excessive current may begin to flow through the wiring to the control valve resulting in overheating of the wiring.
NHTSA · Estados Unidos11 sept 198484V107000Años modelo 1984Mostrado en inglés original · traducción pendienteVer detalles →
On certain 320I vehicles, crack in the exhaust system between the exhaust pipe and the catalytic converter could result in exhaust emissions which do not comply with CMVSS 1103.
Transport Canada22 dic 19831983121Años modelo 1981–1982Mostrado en inglés original · traducción pendienteVer detalles →
On certain 318I vehicles, improper starting procedure could cause a backfire into the intake manifold and damage internal components of the idle control valve. This could result in abnormally high idle speed and if warnings of increased engine noise level and tachometer reading are not heeded, a vehicle crash could occur.
Transport Canada6 jun 19851985072Años modelo 1984Mostrado en inglés original · traducción pendienteVer detalles →
Fuentes: NHTSA (Estados Unidos, dominio público), Transport Canada (Licencia de Gobierno Abierto – Canadá), DVSA (Reino Unido, Open Government Licence v3.0), RappelConso y Safety Gate de la UE (Francia, Licence Ouverte 2.0), MLIT (Japón, Licencia de Datos Públicos 1.0) y MOLIT (Corea del Sur, car.go.kr).