Boletín
No gira el motor/No arranca; batería agotada debido a una descarga parasitaria.
Los boletines técnicos (TSB) son instrucciones de reparación que los fabricantes envían a sus concesionarios sobre problemas conocidos. No son llamadas a revisión de seguridad, pero a menudo confirman una avería.
No gira el motor/No arranca; batería agotada debido a una descarga parasitaria.
17459 - Actualización de servicio. Algunos vehículos pueden tener una base de carga inalámbrica que no funciona. El cliente no podrá cargar su teléfono celular con un cargador inalámbrico. Los concesionarios deben revisar si falta un fusible. Instale un fusible nuevo y verifique el funcionamiento de la base de carga inalámbrica.
This Preliminary Information communication provides information to the technician about vehicles that may have misfires or rough running on cold start up. Technician may find a Diagnostic Trouble Code P0300. Technician will need to use a scan tool and observe Crankshaft Position Re-sync Counter parameter. The Re-sync Counter parameter should remain at 0 during all operating conditions, and while manipulating the related harnesses and connectors between the crankshaft position sensor and the Engine Control Module. Technician will need to inspect for water intrusion in related connectors, terminals, and components. Tech will need to bring the vehicle up to engine coolant temperature that was stored when Diagnostic Trouble Code P0300 was set. After the engine coolant temperature is up to temperature technician will need to perform compression and cylinder leakage and record the readings. Technician should also verify correct fuel system pressure, inspect the heated oxygen sensors for contamination from fuel, silicon, or the incorrect use of room temperature vulcanization silicone sealant, and inspect the spark plugs for incorrect heat range, coolant or oil fouling, carbon tracking, cracks or insulator fractures at the tip. Technician should also Test for coolant contamination into the cylinders.
Esta comunicación de Información Preliminar proporciona al técnico información sobre vehículos que tienen la batería de alto voltaje. Las lengüetas del conector X3 podrían dañarse durante el servicio. El técnico deberá tener cuidado al retirar e instalar este conector. Los conectores deben estar alineados entre sí antes de activar el bloqueo de leva.
Esta comunicación de información preliminar proporciona información al técnico sobre vehículos que presentan un no arranque o múltiples mensajes en el Centro de Información del Conductor durante el clima frío. El técnico deberá revisar la etiqueta del Módulo de Interfaz de Comunicación del Vehículo para ver si dice "Assembled in China". Si la fecha está entre el 18/7/2014 y el 3/8/2014, anote el Identificador de Estación de la etiqueta y llame al Centro de Asistencia Técnica de General Motors, haciendo referencia a esta Información Preliminar para obtener más ayuda.
This Preliminary Information communication provides information to the technician about vehicles that may have misfires or rough running on cold start up. Technician may find a Diagnostic Trouble Code P0300. Technician will need to use a scan tool and observe Crankshaft Position Re-sync Counter parameter. The Re-sync Counter parameter should remain at 0 during all operating conditions, and while manipulating the related harnesses and connectors between the crankshaft position sensor and the Engine Control Module. Technician will need to inspect for water intrusion in related connectors, terminals, and components. Tech will need to bring the vehicle up to engine coolant temperature that was stored when Diagnostic Trouble Code P0300 was set. After the engine coolant temperature is up to temperature technician will need to perform compression and cylinder leakage and record the readings. Technician should also verify correct fuel system pressure, inspect the heated oxygen sensors for contamination from fuel, silicon, or the incorrect use of room temperature vulcanization silicone sealant, and inspect the spark plugs for incorrect heat range, coolant or oil fouling, carbon tracking, cracks or insulator fractures at the tip. Technician should also Test for coolant contamination into the cylinders.
This Preliminary Information communication provides information to the technician about vehicles that may have misfires or rough running on cold start up. Technician may find a Diagnostic Trouble Code P0300. Technician will need to use a scan tool and observe Crankshaft Position Re-sync Counter parameter. The Re-sync Counter parameter should remain at 0 during all operating conditions, and while manipulating the related harnesses and connectors between the crankshaft position sensor and the Engine Control Module. Technician will need to inspect for water intrusion in related connectors, terminals, and components. Tech will need to bring the vehicle up to engine coolant temperature that was stored when Diagnostic Trouble Code P0300 was set. After the engine coolant temperature is up to temperature technician will need to perform compression and cylinder leakage and record the readings. Technician should also verify correct fuel system pressure, inspect the heated oxygen sensors for contamination from fuel, silicon, or the incorrect use of room temperature vulcanization silicone sealant, and inspect the spark plugs for incorrect heat range, coolant or oil fouling, carbon tracking, cracks or insulator fractures at the tip. Technician should also Test for coolant contamination into the cylinders.
Chevrolet: On certain vehicles, after updated calibrations were installed, may exhibit a possible and an estimated electric range drop. *pe updated 12/7/11. *pe
Esta información preliminar explica al personal de campo cómo diagnosticar un problema de GPS en el módulo telemático sin códigos de avería (DTC).
Esta información preliminar explica al personal de campo cómo diagnosticar un problema de GPS en el módulo telemático sin códigos de avería (DTC).
Esta información preliminar explica al personal de campo cómo diagnosticar un problema de GPS en el módulo telemático sin códigos de avería (DTC).
Esta información preliminar comunica al personal de campo cómo diagnosticar un problema del GPS con el módulo telemático sin códigos DTC.
Este boletín de servicio ofrece información al cliente sobre la ausencia ocasional de las instrucciones relativas a la cámara trasera, debido a que el sistema VBM se hace cargo de la opción de la cámara trasera.
Actualización de servicio para inventario y vehículos de clientes Radio de navegación conectada: el comando de voz no funciona Vence con la garantía base
Actualización de servicio para vehículos en inventario y de clientes: El comando de voz de la radio con navegación conectada no funciona. Vence con la garantía base. Equipados con radio con navegación conectada (UHQ)
This service bulletin provides information to the customer about the rear camera guidelines not being present at times due to the VBM taking over the rear camera option.
Este boletín informativo proporciona información al cliente sobre el hecho de que, en ocasiones, no se muestren las instrucciones relativas a la cámara trasera debido a que el sistema VBM se hace cargo de la función de la cámara trasera.
This service bulletin provides repair information to correct a customer concern that Radio is Theft Locked.
Este boletín de servicio proporciona información de reparación para corregir una inquietud del cliente sobre reinicios del radio o reinicios que pueden mostrar la animación de inicio (splash) de myBrand.
Retiro por emisiones. General Motors ha decidido llevar a cabo un retiro voluntario por emisiones que afecta a ciertos vehículos equipados con motores de 4 cilindros (RPO LHN, LEX, L3A, LYX, LKN, LE2, LCV o LTG). En algunos vehículos, una conexión eléctrica en la placa de circuito del módulo de control del motor puede fallar. Si esto ocurre, puede encenderse una luz indicadora de mal funcionamiento (MIL), como la luz de Check Engine. Reemplace el módulo de control del motor (ECM).
Retiro por emisiones. General Motors ha decidido llevar a cabo un retiro voluntario por emisiones que afecta a ciertos vehículos equipados con motores de 4 cilindros (RPO LHN, LEX, L3A, LYX, LKN, LE2, LCV o LTG). En algunos vehículos, una conexión eléctrica en la placa de circuito del módulo de control del motor puede fallar. Si esto ocurre, puede encenderse una luz indicadora de mal funcionamiento (MIL), como la luz de Check Engine. Reemplace el módulo de control del motor (ECM).
Este boletín de servicio proporciona información de reparación para corregir una queja del cliente sobre problemas de software con la versión de software de radio V808.
Esta información preliminar comunica una preocupación en la que la radio se reinicia de forma intermitente al ajustar el volumen, y que la ingeniería está investigando.
Esta información preliminar comunica una preocupación en la que la radio se reinicia al ajustar el volumen de forma intermitente, y que la ingeniería está investigando.
Malfunction Indicator Lamp (MIL) On, Possible P0300, P040B, P041B, P1427 and/or P1429 DTCs Set Some customers may comment on a check engine light illuminated. During diagnosis a technician may find one or more of the following DTCs set: P0300 Engine Misfire Detected P040B Exhaust Gas Recirculation Temperature Sensor 2 Circuit Range/Performance P041B Exhaust Gas Recirculation Temperature Sensor 1 Circuit Range/Performance P1427 EGR Temperature Sensor 1 Intake Air Temperature 1 Not Plausible P1429 EGR Temperature Sensor 2 Intake Air Temperature 1 Not Plausible This may be caused by a calibration within the K20 Engine Control Module
Fuentes: NHTSA (Estados Unidos, dominio público), Transport Canada (Licencia de Gobierno Abierto – Canadá), DVSA (Reino Unido, Open Government Licence v3.0), RappelConso y Safety Gate de la UE (Francia, Licence Ouverte 2.0), MLIT (Japón, Licencia de Datos Públicos 1.0) y MOLIT (Corea del Sur, car.go.kr).