Los boletines técnicos (TSB) son instrucciones de reparación que los fabricantes envían a sus concesionarios sobre problemas conocidos. No son llamadas a revisión de seguridad, pero a menudo confirman una avería.
Algunos clientes pueden experimentar los siguientes síntomas con el cargador inalámbrico (Qi), incluso cuando el dispositivo móvil (smartphone, etc.) se coloca en la posición correcta sobre el cargador inalámbrico (Qi). No comienza a cargarse. Deja de cargarse y el indicador parpadea en rojo tras comenzar. Deja de cargarse sin ningún indicio visible tras comenzar. En el caso del CX-50, es posible que algunos clientes observen que, a pesar de colocar el iPhone equipado con MagSafe en el centro del cargador inalámbrico, la carga se detiene al cabo de unos diez segundos. Los iPhones equipados con MagSafe utilizan imanes para alinear el cargador y el dispositivo. Al cargar iPhones con MagSafe utilizando un cargador no compatible con MagSafe, una alineación incorrecta puede provocar que los imanes perturben el campo magnético necesario para la carga, lo que reduce significativamente la eficiencia de la misma.
MNAO ha detectado recientemente un aumento en los núcleos no devueltos dentro del programa de intercambio de United Radio (UR). Como recordatorio, los concesionarios tienen 90 días, a partir de la fecha en que se realiza el pedido, para devolver la pieza intercambiada. Si no se devuelve la pieza intercambiada, se realizará un cargo por el precio completo del componente. Se recomienda encarecidamente programar un recordatorio en el calendario en el momento del pedido para no más de 60 días, a fin de asegurar que todos los pedidos se devuelvan si han sido reparados y, si no han sido reparados, contactar al cliente para cancelar el pedido y devolver la unidad.
Some customers may experience the following symptoms of the wireless charger (Qi), even when the mobile device (smartphone etc.) is placed in the proper position on the wireless charger (Qi). - It does not start charging. - Soon after starting, it stops charging with the indicator flashing in red. - Soon after starting, it stops charging without any visible sign. These symptoms may be caused by improper control software of the wireless charger (Qi). To eliminate these concerns, the specification of the wireless charger (Qi) has been modified. NOTE: The modifications for the symptoms are different depending on the model.
NHTSA · boletín del fabricante10243549Años modelo 2021Mostrado en inglés original · traducción pendienteVer detalles →
When installing a navigation SD card, confirm that the card is unlocked. Also, Mazda Does Not Recommend swapping navigation system SD cards from one vehicle to another for testing. If swapped, the SD card that is installed into the other vehicle becomes linked to the VIN of that vehicle.
NHTSA · boletín del fabricante10185967Años modelo 2016Mostrado en inglés original · traducción pendienteVer detalles →
If you experience issues with the current version of ID's such as missing tools or modules not showing after completing a network test, be advised that we are aware of these issues and are working to resolve them. As a counter measure, it is advised that you un-install ids and re-install version 103.00 and "do not update" until further notice.
NHTSA · boletín del fabricante10185813Años modelo 2017Mostrado en inglés original · traducción pendienteVer detalles →
Some customers may experience a SBS/SCBS, LAS/LDWS and/or HBC warning light on. A system error message may also be found in the center display. DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction). DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction) is stored in the FSC module and cannot be erased. This concern may be caused by an internal FSC failure. To eliminate this concern, the production process of the FSC has been modified.
NHTSA · boletín del fabricante10154454Años modelo 2018Mostrado en inglés original · traducción pendienteVer detalles →
Some 2018 vehicles built after January 1, 2018 and equipped with Navigation may exhibit one of these concerns after the user inputs an address: A screen pops up that says "House number not found." After the user selects OK, the system finds the address or a nearby address.Instead of finding the correct address number the system adds a digit to the end of the number. Example: You enter 151 and the system comes back with 1510, 1511, 1515, 1516, etc. This only occurs with MAZDA CONNECT software version 59.00.532 or 59.00.540, which started being installed into vehicles in January 2018. The concern can be eliminated by installing MAZDA CONNECT software version 59.00.545 now available on MGSS.
NHTSA · boletín del fabricante10136765Años modelo 2018Mostrado en inglés original · traducción pendienteVer detalles →
Algunos vehículos 2018 fabricados después del 1 de enero de 2018 y equipados con Navegación pueden presentar uno de estos problemas después de que el usuario introduce una dirección: aparece una pantalla que dice "Número de casa no encontrado". Al seleccionar OK, el sistema encuentra la dirección o una dirección cercana.
En lugar de encontrar el número de dirección correcto, el sistema agrega un dígito al final del número. Por ejemplo: si introduce 151, el sistema devuelve 1510, 1511, 1515, 1516, etc.
Esto solo ocurre con la versión 59.00.540 del software MAZDA CONNECT, que comenzó a instalarse en los vehículos en enero de 2018. El problema puede eliminarse instalando la versión 59.00.504 del software MAZDA CONNECT.
When the LED headlight auto leveling system initialization has been performed using Mazda Modular Diagnostic System (M-MDS), the LED headlight warning light continues flashing and DTC C0061:54 is stored after unloading the vehicle from a trailer. DTC C0061:54 - [HEADLIGHT AUTO LEVELING SYSTEM] Acceleration sensor initial position learning not completed. This may be caused by a failure of the headlight auto leveling system initialization, which is performed while driving the vehicle.
NHTSA · boletín del fabricante10134696Años modelo 2018Mostrado en inglés original · traducción pendienteVer detalles →
Some vehicles may experience the check engine light on with dtc p2610 and p2507 stored in memory after engine start and room fuse 15a (a) removed. P2610:00: Instrument cluster internal engine off timer performance problem p2507:00: Pcm battery voltage low input as a past malfunction, the customer will not notice it (no warning light illuminated), but the dtc may be found during a vehicle service. P2507 in this situation is only applicable on 2016 and later models. This is caused by the engine being started 3 or more times after a short duration of engine off (less than 15 seconds) with the room fused removed.
NHTSA · boletín del fabricante10105501Años modelo 2016Mostrado en inglés original · traducción pendienteVer detalles →
When installing a navigation sd card, confirm that the card is unlocked. Also, mazda does not recommend swapping navigation system sd cards from one vehicle to another for testing. If swapped, the sd card that is installed into the other vehicle becomes linked to the vin of that vehicle.
NHTSA · boletín del fabricante10091265Años modelo 2016Mostrado en inglés original · traducción pendienteVer detalles →
If you encounter a vehicle with dtc p0137 (circuit low input), check the rear harness at the red circled area in the following diagram. If an aftermarket alarm system is installed, the rear harness might have received damage from electro-tap connectors (a) or to the protector tube (b). This damage is not covered under warranty.
NHTSA · boletín del fabricante10086522Años modelo 2016Mostrado en inglés original · traducción pendienteVer detalles →
If a customer has a vehicle communication related error on their app, perform the following: Disconnect the battery or unplug the module for at least 10 seconds.Reconnect the battery, wait 60 seconds and then have the customer try the app again.If the vehicle starts, order module 0000-8f-z80a.Note: There is a limited supply of the module at this time, therefore only use this part for this specific condition.Due to the limited supply, make sure you were shipped the a level part and not the original part before installing the part.Install the module and program it per mms programming instructions.Instruct the customer to update their account with the new module information, otherwise the mms will not work from the app.
NHTSA · boletín del fabricante10086506Años modelo 2016Mostrado en inglés original · traducción pendienteVer detalles →
Mazda connect software version 55.00.760 is now available on ms3. Use this version for all mazda connect updates, including open ssp98 vehicles. If ssp98 is closed, use tsb 09-024/16 to repair the vehicles.Click on "ids/infotainment", then "mazda connect updates" to download it. Update your usb drives according to the instructions in tsb 09-024/16.Also make sure to select "all files" for "save as type:". If left as "compressed (zipped) folder," the file will be saved as a ".Zip" no matter what you use as an extension.Attn: Technicians - be sure to document the software version installed on the repair order and inform your warranty administrator to provide the information in the repair text of the warranty claim.Mazda is working to make further improvements to the mazda connect infotainment system software, and may issue future software updates to improve system operation and performance. Software version updates can be found on ms3.
NHTSA · boletín del fabricante10086424Años modelo 2016Mostrado en inglés original · traducción pendienteVer detalles →
Some customers may complain about any the following infotainment system concerns: Reboot, Slow reboot in morning, Display frozen, Display blank. NOTE: Rear view monitor operation is normal, No DTC stored
NHTSA · boletín del fabricante10203765Años modelo 2021Mostrado en inglés original · traducción pendienteVer detalles →
Some vehicles may experience a lack of power and the check engine light on with DTC P061B:00 stored in PCM memory under one of the following conditions (A or B). DTC P061B:00 - [PCM] Internal control module torque calculation performance problem. Due to an improper control logic of the PCM, the engine torque calculation error detection is too sensitive. To eliminate this concern, the PCM software has been modified.
NHTSA · boletín del fabricante10190952Años modelo 2019Mostrado en inglés original · traducción pendienteVer detalles →
After Pandora V7.0 was released on March 7th, the following problems have been found on vehicle with MAZDA CONNECT. Navigation voice guidance will skip and cut out losing many words.Pandora will suddenly disconnect and MAZDA CONNECT will revert to the previously used source. If you encounter a vehicle with these issues, DO NOT attempt any repairs on the vehicle. There is nothing wrong with the vehicle. This is an issue with the Pandora APP. Have the customer contact Pandora at pandora-support@pandora.com. NOTE: If the Pandora APP works on the customer's phone, they can stream Pandora using Bluetooth.
NHTSA · boletín del fabricante10185963Años modelo 2016Mostrado en inglés original · traducción pendienteVer detalles →
Some vehicles may experience the check engine light on with DTCs P2096:00, P2097:00 and/or P0524:00 that cannot be cleared by itself, and the check engine light stays on even if the detection condition has gone. P2096:00 - Air fuel too lean P2097:00 - Air fuel too rich P0524:00 - Engine oil pressure too low. This concern may be caused by improper PCM control logic. The PCM software has been modified to eliminate this concern.
NHTSA · boletín del fabricante10180595Años modelo 2019Mostrado en inglés original · traducción pendienteVer detalles →
Some customers may complain about a high frequency noise (like a mosquito sound) while the active driving display is in the flip-up position. The noise may be coming from the capacitor inside the active driving display which vibrates according to the display control frequency. The circuit board resonates with it resulting in an audible noise. To eliminate this concern, the active driving display has been modified to use a higher frequency for the display control.
NHTSA · boletín del fabricante10171849Años modelo 2019Mostrado en inglés original · traducción pendienteVer detalles →
New IDs software version 102.00 and Update 102.01 is now available on MS3 IDs update 102.00 and 102.01 is now available on MS3 under the "IDs/Infotainment" tab.
NHTSA · boletín del fabricante10186918Años modelo 2017Mostrado en inglés original · traducción pendienteVer detalles →
Fuentes: NHTSA (Estados Unidos, dominio público), Transport Canada (Licencia de Gobierno Abierto – Canadá), DVSA (Reino Unido, Open Government Licence v3.0), RappelConso y Safety Gate de la UE (Francia, Licence Ouverte 2.0), MLIT (Japón, Licencia de Datos Públicos 1.0) y MOLIT (Corea del Sur, car.go.kr).