Los boletines técnicos (TSB) son instrucciones de reparación que los fabricantes envían a sus concesionarios sobre problemas conocidos. No son llamadas a revisión de seguridad, pero a menudo confirman una avería.
Este boletín sustituye a los boletines publicados anteriormente que se enumeran a continuación. Los cambios aparecen marcados en rojo. 09-012/21 13/12/21, 10/06/21 y 27/04/21 DESCRIPCIÓN Es posible que algunos clientes experimenten todos los síntomas siguientes: El bloqueo y desbloqueo de las puertas no funciona al pulsar el botón del mando a distancia. 1. El bloqueo y desbloqueo de las puertas no funciona al utilizar el sensor táctil de bloqueo y desbloqueo de las puertas. 2. El motor no arranca al girar la llave de contacto. 3. El mando a distancia se activa por sí solo. 4. La pila de la llave se agota más rápido de lo habitual. 5. Síntomas 1-3: Esto puede deberse a que se aplica una carga excesiva al mando a distancia, lo que deforma los terminales eléctricos y provoca un mal contacto con la pila. Para solucionar este problema, se ha modificado la estructura del mando a distancia con el fin de reducir la deformación de los terminales eléctricos. Síntomas 4 y 5: Esto puede deberse a que se aplica una carga excesiva al mando a distancia, lo que crea un hueco alrededor de la junta por donde entra humedad y corroe la placa de circuitos, lo que a su vez agota la batería de la llave más rápido de lo habitual. Para solucionar este problema, se ha aumentado el grosor de la pared de la carcasa en la superficie de montaje de la junta y se ha mejorado la resistencia de la unión de los componentes para evitar la deformación. PROCEDIMIENTO DE REPARACIÓN Si la batería está defectuosa o mal instalada, sustitúyela y/o instálela correctamente. Si la función de ahorro de energía del mando a distancia está desactivada y la batería está en buen estado y correctamente instalada, sustituya el mando a distancia defectuoso por uno modificado siguiendo las instrucciones de MGSS (PROGRAMACIÓN DE PIEZAS RELACIONADAS CON EL SISTEMA INMOVILIZADOR). NOTA: NO sustituya otros mandos a distancia del vehículo si no presentan ningún problema.
Algunos clientes pueden experimentar los siguientes síntomas con el cargador inalámbrico (Qi), incluso cuando el dispositivo móvil (smartphone, etc.) se coloca en la posición correcta sobre el cargador inalámbrico (Qi). No comienza a cargarse. Deja de cargarse y el indicador parpadea en rojo tras comenzar. Deja de cargarse sin ningún indicio visible tras comenzar. En el caso del CX-50, es posible que algunos clientes observen que, a pesar de colocar el iPhone equipado con MagSafe en el centro del cargador inalámbrico, la carga se detiene al cabo de unos diez segundos. Los iPhones equipados con MagSafe utilizan imanes para alinear el cargador y el dispositivo. Al cargar iPhones con MagSafe utilizando un cargador no compatible con MagSafe, una alineación incorrecta puede provocar que los imanes perturben el campo magnético necesario para la carga, lo que reduce significativamente la eficiencia de la misma.
MNAO ha detectado recientemente un aumento en los núcleos no devueltos dentro del programa de intercambio de United Radio (UR). Como recordatorio, los concesionarios tienen 90 días, a partir de la fecha en que se realiza el pedido, para devolver la pieza intercambiada. Si no se devuelve la pieza intercambiada, se realizará un cargo por el precio completo del componente. Se recomienda encarecidamente programar un recordatorio en el calendario en el momento del pedido para no más de 60 días, a fin de asegurar que todos los pedidos se devuelvan si han sido reparados y, si no han sido reparados, contactar al cliente para cancelar el pedido y devolver la unidad.
Some customers may experience the following symptoms of the wireless charger (Qi), even when the mobile device (smartphone etc.) is placed in the proper position on the wireless charger (Qi). - It does not start charging. - Soon after starting, it stops charging with the indicator flashing in red. - Soon after starting, it stops charging without any visible sign. These symptoms may be caused by improper control software of the wireless charger (Qi). To eliminate these concerns, the specification of the wireless charger (Qi) has been modified. NOTE: The modifications for the symptoms are different depending on the model.
NHTSA · boletín del fabricante10243549Años modelo 2021Mostrado en inglés original · traducción pendienteVer detalles →
Some vehicles may experience a lack of power and the check engine light on with DTC P061B:00 stored in PCM memory under one of the following conditions (A or B). - DTC P061B:00 - [PCM] Internal control module torque calculation performance problem. Condition Condition Description A When cranking is interrupted (likely occurs when the brake pedal is released during cranking) B When accelerating from 1300-1600 rpm with wide open throttle Due to an improper control logic of the PCM, the engine torque calculation error detection is too sensitive. To eliminate this concern, the PCM software has been modified.
NHTSA · boletín del fabricante10218722Años modelo 2019Mostrado en inglés original · traducción pendienteVer detalles →
When installing a navigation SD card, confirm that the card is unlocked. Also, Mazda Does Not Recommend swapping navigation system SD cards from one vehicle to another for testing. If swapped, the SD card that is installed into the other vehicle becomes linked to the VIN of that vehicle.
NHTSA · boletín del fabricante10185967Años modelo 2016Mostrado en inglés original · traducción pendienteVer detalles →
Some vehicles may experience a Tire Pressure Monitoring System (TPMS) warning light improperly illuminates when driving on a smooth road surface even if the TPMS system has been properly initialized at the specified tire air pressure. Please contact the Hotline for a countermeasure repair if a vehicle arrives with this issue. A countermeasure control module is due in July for this concern.
NHTSA · boletín del fabricante10185959Años modelo 2016Mostrado en inglés original · traducción pendienteVer detalles →
Some vehicles may experience one of the following 2 symptoms, even though the windshield is clear. Under certain driving conditions, the Forward Sensing Camera (FSC) may detect a dirty windshield (not clear). NOTE FOR CUSTOMER: The FSC may not work properly under the conditions: The windshield is not clear. The FSC lens is not clear. Driving in heavy rain, dense fog or snow, or into the sun. Driving on a road with no or blurred road lane markings. When the windshield becomes foggy in the winter time or other cold weather conditions and LDWS/HBC warning lights turn on, drive with the defroster on for about 10 minutes. This will help clear the foggy windshield at the FSC.
NHTSA · boletín del fabricante10185957Años modelo 2016Mostrado en inglés original · traducción pendienteVer detalles →
Some vehicles may exhibit a knocking / squeaking noise from the front shock absorber when driving on rough roads and/or when turning the steering wheel while the vehicle is stopped.
NHTSA · boletín del fabricante10185907Años modelo 2016Mostrado en inglés original · traducción pendienteVer detalles →
A/C blows warm air. Some customers may complain about warm air from the climate cointrol vents. This may be caused by improper brazing (A) of the evaporator (B) causing a refrigerant leak fr om the joint between the tubes and the header (D)
NHTSA · boletín del fabricante10186252Años modelo 2016Mostrado en inglés original · traducción pendienteVer detalles →
A/C blows warm air. Some customes may complain about warm air from the climate control vents. This may be caused by condenser corrosion, causing a refrigerant leak.
NHTSA · boletín del fabricante10185803Años modelo 2016Mostrado en inglés original · traducción pendienteVer detalles →
If you experience issues with the current version of ID's such as missing tools or modules not showing after completing a network test, be advised that we are aware of these issues and are working to resolve them. As a counter measure, it is advised that you un-install ids and re-install version 103.00 and "do not update" until further notice.
NHTSA · boletín del fabricante10185813Años modelo 2017Mostrado en inglés original · traducción pendienteVer detalles →
On May 1, 2018, Japan produced vehicles starting using 17 mm hex lug nuts instead of 21 mm on the same size thread. When installing new lug nuts or the accessory Wheel Lock Set, make sure to use the appropriate part number for the vehicle you are working on. NOTE: The Mazda3 produced in Mexico is not affected. Use the GEPC or the Mazda Accessory web site [MXConnect (dealers.mazdausa.com)] to look up the correct part number for the vehicle you are working on.
NHTSA · boletín del fabricante10168119Años modelo 2019Mostrado en inglés original · traducción pendienteVer detalles →
On May 1, 2018, Japan produced vehicles starting using 17 mm hex lug nuts instead of 21 mm on the same size thread. When installing the accessory locking lug nuts, make sure to use the appropriate part number for the vehicle you are working on.
NHTSA · boletín del fabricante10159199Años modelo 2019Mostrado en inglés original · traducción pendienteVer detalles →
On May 1, 2018, Japan produced vehicles starting using 17 mm hex lug nuts instead of 21 mm on the same size thread. When installing new lug nuts or the accessory Wheel Lock Set, make sure to use the appropriate part number for the vehicle you are working on.
NHTSA · boletín del fabricante10159196Años modelo 2019Mostrado en inglés original · traducción pendienteVer detalles →
Some customers may experience a SBS/SCBS, LAS/LDWS and/or HBC warning light on. A system error message may also be found in the center display. DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction).Master Warning Light, Smart Brake Support/Smart City Brake Support (SBS/SCBS) Indicator Light, Lane-keep Assist System (LAS) Lane Departure Warning System (LDWS) Warning Light, High Beam Control (HBC) system Warning Light (amber). DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction) is stored in the FSC module and cannot be erased. This concern may be caused by a hardware failure of an internal device of the FSC, which results in a malfunction detection. To eliminate this concern, the production process of the FSC has been modified.
NHTSA · boletín del fabricante10155440Años modelo 2018Mostrado en inglés original · traducción pendienteVer detalles →
Subject: Mazda Service Program (MSP) 53. 2019 CX-3 & 2018-2019 MX-5 With Direct Tire Pressure Monitoring System (TPMS) Panic Alarm System Activates While Driving. Mazda Motor Corporation has decided to conduct a Mazda Service Program (MSP) on certain 2019 CX-3 vehicles produced from February 27, 2018 through October 12, 2018 and 2018-2019 MX-5 vehicles produced from October 3, 2017 through October 15, 2018. On certain subject vehicles equipped with Direct TPMS (TPMS wheel sensor is directly mounted on each wheel), it is possible that the panic alarm system may activate while driving, and the horn may sound intermittently, and hazard warning lights may flash. The panic alarm concern will stop after cycling the ignition switch off, then on again. No DTCs are stored. Action Required: Beginning today, reprogram the body control module (BCM) to the latest calibration using MMDS for all affected CX-3 and MX-5 vehicles in dealer inventory, and when customers bring their vehicles for maintenance, or other service/warranty work. The subject vehicles must not be delivered to customers until the repair of MSP53 is completed. Please inform the customer that the BCM will be reprogrammed to the latest calibration, free of charge. If a vehicle is sold with an open MSP53 your Step 3 PDI warranty claim will be subject to debit.
NHTSA · boletín del fabricante10154528Años modelo 2019Mostrado en inglés original · traducción pendienteVer detalles →
On certain subject vehicles, it is possible that the panic alarm system may activate while driving, and the horn may sound intermittently and hazard warning lights may flash. The panic alarm concern will stop after cycling the ignition switch off, then on again. No DTCs are stored. Some TPMS wheel sensor IDs on the concerned vehicle or other vehicles nearby may cause the error in the body control module (BCM). Air pressure data transmitted from the wheel sensors may be recognized by the BCM as if the panic button on the remote transmitter has been pressed.
NHTSA · boletín del fabricante10154531Años modelo 2019Mostrado en inglés original · traducción pendienteVer detalles →
Some customers may experience a SBS/SCBS, LAS/LDWS and/or HBC warning light on. A system error message may also be found in the center display. DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction). DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction) is stored in the FSC module and cannot be erased. This concern may be caused by an internal FSC failure. To eliminate this concern, the production process of the FSC has been modified.
NHTSA · boletín del fabricante10154454Años modelo 2018Mostrado en inglés original · traducción pendienteVer detalles →
As of May 1, 2018, Japan produced vehicles use 17 mm hex lug nuts instead of 21 mm on the same size thread. When installing new lug nuts or the accessory Wheel Lock Set, make sure to use the appropriate part number for the vehicle you are working on. NOTE: The Mazda3 produced in Mexico is not affected.Use the GEPC or the Mazda Accessory web site [MXConnect (dealers.mazdausa.com)] to look up the correct part number for the vehicle you are working on.
NHTSA · boletín del fabricante10153226Años modelo 2019Mostrado en inglés original · traducción pendienteVer detalles →
On May 1, 2018, Japan produced vehicles starting using 17 mm hex lug nuts instead of 21 mm on the same size thread. When installing the accessory locking lug nuts, make sure to use the appropriate part number for the vehicle you are working on.
NHTSA · boletín del fabricante10153304Años modelo 2019Mostrado en inglés original · traducción pendienteVer detalles →
Some vehicles may experience a lack of power and the check engine light on with DTC P061B:00 and U0401:00 stored in the PCM memory when engine cranking is interrupted and on A/T vehicles, DTC U0442:00 is also stored. This concern most likely occurs when the brake pedal is released during engine cranking. DTC P061B:00 - [PCM] Internal control module torque calculation performance problem. DTC U0401:00 - Signal error from PCM DTC U0442:00 - [TCM] Invalid data received from PCM. Due to an improper control logic of the PCM, the engine torque calculation error detection is too sensitive. To eliminate this concern, the PCM software has been modified.
NHTSA · boletín del fabricante10148004Años modelo 2019Mostrado en inglés original · traducción pendienteVer detalles →
Some vehicles may experience a check engine light on and/or failsafe with DTC P061B:00 stored in the PCM. This condition will likely occur as a result of one of the following causes: Engine cranking was interrupted by releasing the brake pedal. Start button was double pressed while the engine was still cranking. A countermeasure to correct mis-detection is currently being prepared.
NHTSA · boletín del fabricante10144336Años modelo 2019Mostrado en inglés original · traducción pendienteVer detalles →
Fuentes: NHTSA (Estados Unidos, dominio público), Transport Canada (Licencia de Gobierno Abierto – Canadá), DVSA (Reino Unido, Open Government Licence v3.0), RappelConso y Safety Gate de la UE (Francia, Licence Ouverte 2.0), MLIT (Japón, Licencia de Datos Públicos 1.0) y MOLIT (Corea del Sur, car.go.kr).