Boletín
N12 Tank leak diagnostic module (DMTL) pump:limited warranty extension to 10 years/120,000 miles
🔔 Crea una cuenta gratuita para recibir alertas por correo sobre Mini Hatch II
Los boletines técnicos (TSB) son instrucciones de reparación que los fabricantes envían a sus concesionarios sobre problemas conocidos. No son llamadas a revisión de seguridad, pero a menudo confirman una avería.
N12 Tank leak diagnostic module (DMTL) pump:limited warranty extension to 10 years/120,000 miles
CLASS ACTION SETTLEMENT: N14 HIGH-PRESSURE FUEL PUMP (HDP) SERVICE BENEFIT CLASS VEHICLES: The MINI vehicle may experience a sudden engine operational failure reduced or loss of power while driving and the malfunction indicator lamp (MIL) may be illuminated along with high-pressure fuel pumprelated faults stored in the Engine Control Module (DME). PROCEDURE Perform the corresponding diagnosis/vehicle test and run the test plans to completion as applicable.
**Módulo de diagnóstico de fugas del depósito (DMTL), bomba de N12: extensión de la garantía limitada a 10 años/120 000 millas** **INFORMACIÓN** Esta versión actualizada del boletín incluye ahora los vehículos MINI Cooper R55, R56 y R57 del año modelo 2009 con motor N12. Para los vehículos mencionados, MINI USA, una división de BMW of North America, LLC ("MINI USA"), amplía la garantía limitada de la bomba del módulo de diagnóstico de fugas del depósito (DMTL) a: 10 años/120 000 millas, según la fecha original de puesta en servicio del vehículo. Componente n.º 1: Esta extensión de garantía limitada "específica del componente" cubre defectos de materiales y de mano de obra, y está sujeta a los requisitos de elegibilidad del vehículo y de la cobertura, exclusiones y limitaciones aplicables a la Garantía Limitada para Automóviles de Pasajeros Nuevos MINI. GRUSB0116-04 Este boletín es un aviso de "extensión de garantía limitada". NO es un aviso de llamado a revisión (recall) ni de acción de servicio. No se requiere una reparación inmediata, a menos que el vehículo MINI presente actualmente este problema. Aunque NO se trata de un llamado a revisión, MINI USA enviará cartas de notificación al cliente específicas por VIN en una entrega por fases. **Carta de notificación al cliente: extensión de garantía específica por VIN y componente** Aunque NO se trata de un llamado a revisión, MINI USA enviará cartas de notificación al cliente específicas por VIN en una entrega por fases para los vehículos adicionales del año modelo 2009.
N16: La avería 274D de adaptación de mezcla se almacena en la DME. Ciertas condiciones de conducción a baja velocidad y con carga ligera, con temperaturas exteriores más bajas, podrían hacer que se encienda la luz de Service Engine Soon (MIL). La siguiente avería se almacenaría en la DME: Avería 274D: Adaptación de mezcla, rango de régimen bajo del motor (mezcla demasiado pobre) CAUSA 1. Posibles fugas en la admisión/escape, o un componente defectuoso como se indica en el plan de pruebas 2. Software de la DME desfavorable
Service Action: Bluetooth Software (KISU Data) Update. This Service Action is being released to improve customer satisfaction as we strive to be number 1 in the JD Power Initial Quality Survey (IQS). This new KISU software improves the Bluetooth functionality in our vehicles, and it helps to keep us up-to-date with technology innovation. Please implement the Bluetooth Software Update Service Action. This Service Action will be in effect until March 2015. Thank you for your continuous support. Improved KISU data (Customer Initiated Software Update) is now available for installation in these vehicles via the USB port. Improved functionality for COMBOX: z Detailed view of the text messages z Android device connection stability (linked contacts causing BT disconnection) Improved functionality for HU-H: z Reconnection strategy z 3rd Party App Metadata - Album art and song title Note: This Service Action is to be completed only at the dealer. You (dealers) will be receiving vehicles from the VDCs that will require this Service Action to be completed prior to customer delivery.
"N16 and N18 Engine Oil Leak. The customer states that a small engine oil leak can be seen from the underside of the engine. CAUSE The internal sealing of the oil pump volume control solenoid valve is compromised, allowing engine oil to leak from the oil pump volume control solenoid. DIAGNOSTIC Below is the procedure for identifying how far the engine oil has migrated inside the engine electrical harness, when this issue occurs, if at all. The procedure must be followed very carefully so that the proper repair is identified. 1. Disconnect the oil pump volume control solenoid valve electrical connection per Repair Instructions 11 41 519 ""Removing and installing or replacing the solenoid valve (engine oil pump)."" Inspect the electrical connector; if no engine oil is found inside the electrical connector, perform the oil pump volume control valve repair procedure. If engine oil is found inside the electrical connector, proceed to diagnostic procedure step 2. 2. Remove the cover from the DME and remove all three electrical connectors from the DME. Inspect the connectors for traces of engine oil. If no engine oil is found, perform the oil pump volume control valve repair procedure and replace the engine section of the wire harness. Refer to EPC for the additional part number. If engine oil is found in the DME connector, proceed to step 3. 3. If engine oil is found in the DME electrical connector, perform the oil pump volume control valve repair procedure, replace the engine section of the wire harness and replace the DME. Refer to EPC for the additional part numbers. Do not remove the engine oil pan. Do not replace the oil pump volume control valve. Do not replace engine oil pump. OIL PUMP VOLUME CONTROL VALVE REPAIR"
N16: Fault 274D Mixture Adaptation Is Stored in the DME. Certain low speed, light-load driving conditions at lower outside temperatures could cause the Service Engine Soon lamp (MIL) to illuminate. The following fault would be stored in the DME: ??Fault 274D: Mixture adaptation, lower engine speed range (mixture too lean) CAUSE 1. Possible intake/exhaust leaks, or a faulty component as listed in the test plan 2. Unfavorable DME software.
FOOTWELL MODULE: LIMITED WARRANTY EXTENSION TO 8 YEARS/125,000 MILES. When performing ISTA/D diagnosis and/or a programming procedure (software update) on an affected vehicle, the Footwell Module could fail. There is a compatibility issue with certain combinations vehicle software (Plant Integration ILevel) and the Footwell Module hardware installed in the vehicle.
Mini: A mechanical failure and dme software error of the vanos actuators cause the engine to run rough which activates the malfunction warning light. *ma
Mini: The engine thermostat housing had poor solder contacts in coolant temperature sensor which caused a no start, or hard, long crank start of a cold engine. No models or model years listed. *pe
Bmw: The service engine light is on with fault codes stored. Driveability is not affected. It is a tank leak diagnostic pump problem. *rm
Bmw: Warning light is on and the selector lever could not be moved out of park which was likely caused by fluid being spilled on the shifter. *rm
MINI electrical systems have continued to develop over the past few years. As a result, the demand on the batteries has increased. Breakdowns due to an empty battery or problems in the vehicles electrical system can have various causes, most of which are not due to the battery itself. For this reason, a battery replacement will permanently eliminate the problem only in the rarest of cases. The energy diagnosis test module helps to localize these causes. This document covers important information for the dealer on how to handle discharged battery complaints. Without performing the energy diagnosis test plan, the root cause of a discharged battery cannot be identified. In order to properly repair the vehicle the first time, it is very important that the diagnostic test plan is performed to completion; with all results taken into consideration.
N18 Engine: FC 37DE Engine Ventilation, Heating, Triggering Stored in the DME After Programming. The Service Engine Soon lamp is illuminated after reprogramming the vehicle to integration level R056-11-11503 (ISTA/P P45.1.3.0) or higher. When diagnosed, the following fault code is stored in DME fault memory: ??37DE Engine ventilation, heating, triggering: open circuit CAUSE Due to a DME software change, the diagnostic monitoring capability is improved for the engine ventilation heating system. However, a fault will be stored in the fault memory because the engine ventilation heater circuit has a malfunction currently present.
"The Service Engine Soon (MIL) lamp is illuminated and/or the customer complains that the engine runs rough (engine cold or warm) with any of the following misfire faults stored in the DME: * 2771, 2772, 2773, 2775, 2776, 2777, 2779, 277A, 277B, 277D, 277E, 277F - ""Combustion misfire, cylinder 1..4"", sometimes together with: * 2781, 2782, 2783 - ""Combustion misfire, multiple cylinders"" On rare occasions, the Service Engine Soon lamp may not be illuminated (with misfire faults still stored in the DME) when the vehicle is brought to the workshop. Multiple causes related to electrical and mechanical engine components, or poor fuel quality in combination with unfavorable driving behavior (low loads and short driving distances). This condition may lead to possible clogging of the injector tips, causing a disturbance of the fuel spraying pattern or excessive carbon deposits on the intake valves/ports, resulting in reduced air flow into the combustion chambers."
Engine Misfire Due to Failed Ignition Coil This Service Information bulletin supersedes SI M12 01 15 dated March 2016.. The Check Engine or Service Engine Soon (MIL) lamp is on with misfire fault(s) stored in the DME. Intermittent performance or rough running without a relevant DME fault stored The most likely cause is that an ignition coil has failed, which in many cases can be confirmed with basic diagnosis. During operation with high temperature fluctuations, the different materials used in the Bosch ignition coil construction can deteriorate over time, leading to a failure.
"Cooper S with N14: Diagnosis for Misfire Faults. The Service Engine Soon (MIL) lamp is illuminated and/or the customer complains that the engine runs rough (engine cold or warm) with any of the following misfire faults stored in the DME: ??2771, 2772, 2773, 2775, 2776, 2777, 2779, 277A, 277B, 277D, 277E, 277F - ""Combustion misfire, cylinder 1..4"", sometimes together with: ??2781, 2782, 2783 - ""Combustion misfire, multiple cylinders"" On rare occasions, the Service Engine Soon lamp may not be illuminated (with misfire faults still stored in the DME) when the vehicle is brought to the workshop. Multiple causes related to electrical and mechanical engine components, or poor fuel quality in combination with unfavorable driving behavior (low loads and short driving distances). This condition may lead to possible clogging of the injector tips, causing a disturbance of the fuel spraying pattern or excessive carbon deposits on the intake valves/ports, resulting in reduced air flow into the combustion chambers."
"Discharged Battery: Energy Diagnosis Must Be Performed. MINI electrical systems and advancements in vehicle technology have resulted in an increased demand on the vehicle battery. This SI will help the dealer handle ""discharged battery"" complaints. A discharged battery can have various causes, most unrelated to the battery. A failed battery is often the symptom and not the cause. A fully serviceable battery fails when an electrical component causes the battery to discharge; the battery becomes internally damaged and must be replaced. For more information, refer to http://www.batteryuniversity.com/parttwo-42B.htm. For this reason, replacing the battery is not usually a permanent repair. The cause of the discharged battery must be analyzed in order to guarantee a proper repair. To properly repair the vehicle the first time in the workshop, the diagnostic test plans must be performed to completion, with all results taken into consideration. The procedure below will guide the technician to properly repairing the vehicle and getting paid for a warranty claim. CAUSE Discharged battery."
Intermittent Humming or Buzzing Noise from Speedometer. When the vehicle is decelerating, an intermittent humming or buzzing noise coming from the instrument cluster may be heard when the speedometer needle is between 0 and 12 mph. Hardware error in the instrument cluster
?N18 Engine: FC 2BF2 Rail Pressure Sensor Is Stored in DME Fault Memory. The customer states that the Service Engine Soon lamp is illuminated and the following fault is stored in the DME: FC 2BF2 Rail pressure sensor, workspace: pressure too high CAUSE A DME calibration error in the fuel pressure diagnostics results in an increased sensitivity.
Incorrect Customer Relations Telephone Number Is Saved in the Vehicle. The customer is not connected to MINI Customer Relations after dialing the number displayed in the vehicle Kombi or radio. CAUSE During the Pre-Delivery Inspection (PDI), the incorrect telephone number is being written into the vehicle. INFORMATION 1. When performing the PDI test plan, it is extremely important that you select MINI if the ISID is configured for both BMW and MINI. 2. After completion of the PDI test plan, verify that the customer relations number stored in the vehicle is correct. 3. The correct customer relations phone number is 1(866) 275-6464. 4. If the number stored in the vehicle is incorrect and the correct test plan was used, contact your 3g Administrator and have him or her verify the number stored in the ISID. 5.This picture shows the correct number stored in the Combox control unit. Note: To read out telephone number:
N16 Engine: FC 2D9B Knock Sensor, Signal Is Stored in the DME. Certain areas of the US experience extremely cold climate conditions during the winter months, which can cause the Service Engine Soon lamp to illuminate while the engine temperature is increasing to full operating temperature. The following fault may be stored in the DME: ??FC 2D9B Knock Sensor, Signal CAUSE Unfavorable DME knock sensor diagnostic at outside ambient temperatures below -5 C
"Service Action: Convertible Top Does Not Close. During the closing process, it is possible that the convertible top locating pin on the right side is not correctly positioned in the landing plate at the top of the A-pillar (passenger's side). AFFECTED VEHICLES This Service Action affects certain R57 vehicles produced from July 2013 to October 2013. 3.This picture shows the left side locating pin correctly positioned in the landing plate on the driver's side A-pillar. 4.The passenger's side should In order to determine whether a specific vehicle has had this Service Action completed or is affected by this Service Action, first check the B-pillar label for code number 63. If code number 63 has been punched out, the campaign has already been performed. If code number 63 has not been punched out, it will be necessary to utilize the "Service Menu" of DCSnet (Dealer Communication System) or the Key Reader. Based on the response of the system, either proceed with the corrective action or take no further action. Important Note: A Campaign can be reserved in ISPA Light as "Pending" prior to submission of a claim. If you find this Campaign reserved, please verify the reason before attempting to perform this repair."
"CHAMP2: Stored Radio Stations Deleted After Ignition Off. After ignition off, the stored radio stations (AM/FM and Satellite radio) are no longer available in: * Menu ""PRESETS"" * Preset buttons on the head unit Hardware error in the CHAMP2 head unit"
"HAMP2: Stored Radio Stations Deleted After Ignition Off. After ignition off, the stored radio stations (AM/FM and Satellite radio) are no longer available in: * Menu ""PRESETS"" * Preset buttons on the head unit Hardware error in the CHAMP2 head unit"
Fuentes: NHTSA (Estados Unidos, dominio público), Transport Canada (Licencia de Gobierno Abierto – Canadá), DVSA (Reino Unido, Open Government Licence v3.0), RappelConso y Safety Gate de la UE (Francia, Licence Ouverte 2.0), MLIT (Japón, Licencia de Datos Públicos 1.0) y MOLIT (Corea del Sur, car.go.kr).