Lecture libre · compte gratuit pour contribuerSuccesseur d’Anticars (2000)

BMW M3

1986– · 6 générations · 15 défauts documentés · 2 marchés
Générations

Les bulletins techniques (TSB) sont des instructions de réparation que les constructeurs envoient à leurs concessionnaires sur des problèmes connus. Ce ne sont pas des rappels de sécurité, mais ils confirment souvent un défaut.

Année modèle
MarchéTousNA
E90/92/93 M3 · 2007–2013
BulletinCritiqueÉlectroniqueNA

Bulletin

"? NO REGENERATION OF THE DIESEL PARTICULATE FILTER (DPF) This Service Information bulletin supersedes SI B18 03 10 dated November 2010. . The Service Engine Soon lamp is illuminated. The following fault codes may be stored in the DDE: N47T/N57T engine 245700 - Particle filter system: particulate filter highly loaded (Exhaust backpressure high) 245800 - particle filter system - filter is heavily contaminated. (exhaust backpressure is above maximum) M57Y engine 480A Particle filter system - filter is heavily contaminated. (exhaust backpressure is too high) 481A Particle filter system - filter is heavily contaminated. (exhaust backpressure is above maximum) CAUSE 1. Faults with the exhaust system that affect the monitoring of the DPF by the DDE 2. Unfavorable recent driving profile INFORMATIOM During normal driving, there is a continuous regeneration of the diesel particulate filter that takes place at exhaust-gas temperatures between 280 and 350C (slower oxidation process). The soot particles can only be burned off when the required exhaust-gas temperature has been reached. Under certain driving conditions (i.e., prolonged short trips or an exhaust system which never reaches soot burn-off temperatures), the DPF can become restricted. The DDE will initiate periodic regeneration automatically, at the latest after 600 miles. In vehicles making many short distance journeys, periodic regeneration takes place after only 250-500 miles. The Digital Diesel Electronics control unit evaluates the time for periodic regeneration from the following values: average distance driven average driving speed temperature in the diesel particulate filter values from the exhaust pressure sensor The DDE initiates the regeneration process by decreasing incoming air by the throttle valve, and one or two post injections are executed. This heats the exhaust-gas temperature to approx. 600 C . When the exhaust temp reaches this point: The soot is burned off with the residual oxygen. The

NHTSA · bulletin constructeur10146535Années modèle 2011Affiché en anglais d’origine · traduction en attenteVoir le détail →
E90/92/93 M3 · 2007–2013
BulletinModéréÉlectroniqueNA

Bulletin

Butt connector for repairing a plug connection. The ?top up coolant? message is displayed in the central display (CC message ID 166). When checking the cooling system there are no leaks found and the expansion tank is filled to the proper level.

NHTSA · bulletin constructeur10193494Années modèle 2013Affiché en anglais d’origine · traduction en attenteVoir le détail →
G80 M3 · 2020–
BulletinModéréÉlectroniqueNA

Bulletin

COMFORT ACCESS AND COMFORT GO NOT POSSIBLE: Vehicle cannot be unlocked/locked or started via Comfort Access. Remote control functionality is restored by pressing any of the key buttons or by removing and reinstalling the remote control key battery.

NHTSA · bulletin constructeur10179824Années modèle 2020Affiché en anglais d’origine · traduction en attenteVoir le détail →
G80 M3 · 2020–
BulletinModéréÉlectroniqueNA

Bulletin

KAFAS04 (CAMERA-BASED DRIVER ASSISTANCE SYSTEMS) LIMITATIONS: Various functions of the KAFAS (without radar installed) are not operating up to customer expectations.

NHTSA · bulletin constructeur10175290Années modèle 2020Affiché en anglais d’origine · traduction en attenteVoir le détail →
G80 M3 · 2020–
BulletinModéréÉlectroniqueNA

Bulletin

COMFORT ACCESS AND COMFORT GO NOT POSSIBLE: This Service Information Bulletin (Revision 1) replaces SI B66 19 19 dated May 2019. Vehicle cannot be unlocked/locked or started via Comfort Access. Remote control functionality is restored by pressing any of the key buttons or by removing and reinstalling the remote control key battery. The Display Key Digital Key and the Digital Key Card are not affected. Electrostatic discharge puts the remote control key into a deep sleep. Various situations can lead to an electrostatic charge which is often not recognized by the customer. For example walking over carpet wearing shoes that have a hard rubber sole positive and negative charges are exchanged. The sole accumulates a negative charge and an electrostatic charge develops before touching the remote control key.

NHTSA · bulletin constructeur10174317Années modèle 2020Affiché en anglais d’origine · traduction en attenteVoir le détail →
G80 M3 · 2020–
BulletinModéréÉlectroniqueNA

Bulletin

ENGINE DOES NOT START BELOW FREEZING TEMPERATURES: Engine designation correction Parts availability Warranty. The engine will not start at temperatures below freezing. The starter does not turn and engage.

NHTSA · bulletin constructeur10170572Années modèle 2020Affiché en anglais d’origine · traduction en attenteVoir le détail →
F80 M3 · 2014–2018
BulletinModéréÉlectroniqueNA

Bulletin

"Service Action: Replace Engine Compartment Sound Insulation. The sound insulation in the engine compartment does not seal properly. Manufacturing tolerances and a defect in workmanship may cause the sound insulation to leak water into the DME wiring connector. AFFECTED VEHICLES This Service Action involves F80 and F82 vehicles produced from March 18, 2014 to May 20, 2014. First check if a Service Action label with a code number 698 is already attached to the B-pillar. If a code number 698 has been punched out, the Service Action has already been performed and no further action is necessary. Vehicles which require this Service Action to be completed will show it as ""Open"" when checked either in the ""Service Menu"" of DCSnet (Dealer Communication System) or with the Key Reader."

NHTSA · bulletin constructeur10152310Années modèle 2015Affiché en anglais d’origine · traduction en attenteVoir le détail →
E90/92/93 M3 · 2007–2013
BulletinModéréÉlectroniqueNA

Bulletin

N51 Engine: Service Engine Soon Lamp Illuminated - Loss of Power and Various Faults Stored in the DME. The customer complains that the Service Engine Soon lamp is illuminated. The vehicle has lost power; the engine cranks but will not start; and various faults are stored in the DME for engine misfire and/or mixture adaptations. CAUSE The vehicle has lost fuel system delivery pressure due to a loose or split fuel line inside the fuel tank. The failure is related to an unfavorable stacking of tolerances between the rubber fuel hose and the plastic regulator nipple or deterioration of the rubber hose construction material.

NHTSA · bulletin constructeur10151170Années modèle 2011Affiché en anglais d’origine · traduction en attenteVoir le détail →
E90/92/93 M3 · 2007–2013
BulletinModéréÉlectroniqueNA

Bulletin

Service Action: CIC - Install Navigation Road Map Database 2013. The Car Information Computer (CIC) road map database 2013 must be installed onto the CIC internal Hard Disc Drive (HDD).

NHTSA · bulletin constructeur10150389Années modèle 2011Affiché en anglais d’origine · traduction en attenteVoir le détail →
E90/92/93 M3 · 2007–2013
BulletinModéréÉlectroniqueNA

Bulletin

"Service Action: CIC - Install Navigation Road Map Database 2013. Before delivering affected vehicles to the customer, the Car Information Computer (CIC) road map database 2013 must be installed onto the CIC internal Hard Disc Drive (HDD). Note: The INITIAL enabling code ""FSC CIC map, N. America 2013 INITIAL"" is necessary to start the installation process and to activate the road map database."

NHTSA · bulletin constructeur10150334Années modèle 2011Affiché en anglais d’origine · traduction en attenteVoir le détail →
E90/92/93 M3 · 2007–2013
BulletinModéréÉlectroniqueNA

Bulletin

N51, N52K, N52T and N55 Engine: Various Faults Stored in DME Related to VANOS and Camshaft Position. A rattling noise can be heard from the engine compartment; the engine exhibits a loss of power; and the Service Engine Soon lamp is illuminated. One, or more of the following faults may be stored. E70, E71, E82, E88, E90, E92 and E93: 2D5A - VANOS, intake: control fault, camshaft sticking 2D5B - VANOS, intake: control fault, position not reached 2D54 - VANOS, exhaust, cold start: not controllable 2D55 - VANOS, intake, cold start: not controllable 2D60 - VANOS, exhaust: control fault, camshaft sticking 2D61 - VANOS, exhaust: control fault, position not reached 2D9F - Camshaft input sensor: signal implausible 2DA1 - Camshaft exhaust sensor: signal implausible 300C - Camshaft input sensor: signal high 300D - Camshaft input sensor: signal low 300E - Camshaft exhaust sensor: signal high 300F - Camshaft exhaust sensor: signal low F07, F10, F12, F13 and F25: 130104 - VANOS, intake: control fault, camshaft sticking 130108 - VANOS, intake: control fault, position not reached 130304 - VANOS, exhaust: control fault, camshaft sticking 130308 - VANOS, exhaust: control fault, position not reached 130E11 - Camshaft input sensor: signal implausible 130F11 - Camshaft exhaust sensor: signal implausible 164020 - Camshaft input sensor: signal high 164021 - Camshaft input sensor: signal low 164030 - Camshaft exhaust sensor: signal high 164031 - Camshaft exhaust sensor: signal low CAUSE One, or both (intake and/or exhaust) of the VANOS gear assemblies have failed; the attaching bolts may have also loosened and/or broken.

NHTSA · bulletin constructeur10150033Années modèle 2011Affiché en anglais d’origine · traduction en attenteVoir le détail →
E90/92/93 M3 · 2007–2013
BulletinModéréÉlectroniqueNA

Bulletin

N51, N52K, N52T and N55 Engine: Various Faults Stored in DME Related to VANOS and Camshaft Position. A rattling noise can be heard from the engine compartment; the engine exhibits a loss of power; and the Service Engine Soon lamp is illuminated. One, or more of the following faults may be stored. E70, E71, E82, E88, E90, E92 and E93: 2A7C - VANOS, inlet, cold start 2A82 - VANOS, intake, variable cam control test 2A7A - VANOS, exhaust, cold start 2A87 - VANOS, intake: control fault, camshaft sticking 2D5A - VANOS, intake: control fault, camshaft sticking 2D5B - VANOS, intake: control fault, position not reached 2D54 - VANOS, exhaust, cold start: not controllable 2D55 - VANOS, intake, cold start: not controllable 2D60 - VANOS, exhaust: control fault, camshaft sticking 2D61 - VANOS, exhaust: control fault, position not reached 2D9F - Camshaft input sensor: signal implausible 2DA1 - Camshaft exhaust sensor: signal implausible 300C - Camshaft input sensor: signal high 300D - Camshaft input sensor: signal low 300E - Camshaft exhaust sensor: signal high 300F - Camshaft exhaust sensor: signal low F07, F10, F12, F13 and F25: 130104 - VANOS, intake: control fault, camshaft sticking 130108 - VANOS, intake: control fault, position not reached 130304 - VANOS, exhaust: control fault, camshaft sticking 130308 - VANOS, exhaust: control fault, position not reached 130E11 - Camshaft input sensor: signal implausible 130F11 - Camshaft exhaust sensor: signal implausible 164020 - Camshaft input sensor: signal high 164021 - Camshaft input sensor: signal low 164030 - Camshaft exhaust sensor: signal high 164031 - Camshaft exhaust sensor: signal low CAUSE One, or both (intake and/or exhaust) of the VANOS gear assemblies have failed; the attaching bolts may have also loosened and/or broken.

NHTSA · bulletin constructeur10150218Années modèle 2011Affiché en anglais d’origine · traduction en attenteVoir le détail →
F80 M3 · 2014–2018
BulletinModéréÉlectroniqueNA

Bulletin

BMW Parts Bulletin TEC1T RDC Module Return BMW NA has requested the inspection of the following part numbers: 36 10 6 856 227 and 36 10 6 798 872 Stock should not be sold or installed on any vehicle. Please return the part(s) to your facing Regional Distribution Center (RDC). Submit for return using a YR26 damage claim with order reason BM2. A valid BMW delivery and delivery item number must be entered, and TEC1T must appear in the text of your TEC claim. TEC1T is valid from May 30, 2013, through June 13, 2013.The deadline for filing a claim under TEC1T is June 13, 2013. All parts must be returned to your facing RDC no later than June 27, 2013. Part number 36 10 6 856 227: All parts with an index of 02 and older must be returned. All parts with an index of 03 are correct. Part number 36 10 6 798 872: All parts with an index of 03 and older must be returned. All parts with an index of 04 are correct. The Index is the two digit code under the bar code located on the box label. The Index can also be found on the part itself just after the part number. Please re-order the same part number as needed. (c) 2013, BMW of North America, LLC. The contents of this document are confidential and should not be shared with third parties for distribution.

NHTSA · bulletin constructeur10150084Affiché en anglais d’origine · traduction en attenteVoir le détail →
E90/92/93 M3 · 2007–2013
BulletinModéréÉlectroniqueNA

Bulletin

"N54 Engine: Diagnosis of Cold Start Rough Running with Misfire Faults. The customer may complain that during the cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. Various misfire fault codes (e.g., 29CC, 29D2, 29D1, 29D0, 29C0, 29CF) may be stored in the DME control module. The engine rough running complaint can be reproduced on a cold start in the workshop. During the course of diagnosis, the spark plugs, removed from the misfiring cylinders after the problem was reproduced, are found to be soaked (""wet"") with fuel, while the injector tips are covered with a layer of carbon deposit. Possible cause: high-pressure injector failure (leakage or incorrect spraying pattern) due to internal wear or unfavorable stock of tolerances IMPORTANT: For comprehensive N54 drivability diagnostics, always refer to the ""N54 Engine Diagnostic Fault Tree"" file (the current version ""02_14_13"" is found as a PDF attachment to SI B12 55 06)."

NHTSA · bulletin constructeur10149589Années modèle 2011Affiché en anglais d’origine · traduction en attenteVoir le détail →
F80 M3 · 2014–2018
BulletinModéréÉlectroniqueNA

Bulletin

CLOSED-CIRCUIT CURRENT MONITORING. Increased closed-circuit currents may occur permanently or intermittently and cause the battery to discharge prematurely. The increase in closed-circuit current may be caused by a faulty control module or by the installation of a non-approved accessory. In a situation where a vehicle has broken down due to a discharged battery, for diagnostic purposes it is important not to disconnect the battery. This is because a control module will be reset if the battery is disconnected. Following a reset, the faulty control module may start functioning correctly again, making accurate diagnosis impossible. To correctly measure closed-circuit current, the 50-amp or 100-amp clip-on probe can be used in conjunction with the IMIB (Integrated Measurement Interface Box) to properly diagnose closed-circuit current problems over an extended period of time.

NHTSA · bulletin constructeur10149555Affiché en anglais d’origine · traduction en attenteVoir le détail →
E90/92/93 M3 · 2007–2013
BulletinModéréÉlectroniqueNA

Bulletin

?SI B12 14 12 April 2013 Engine Electrical SystemsTechnical Service This Service Information bulletin supersedes SI B12 14 12 dated January 2013. designates changes to this revision SUBJECT N51, N52K, N52T and N55 Engine: Various Faults Stored in DME Related to VANOS and Camshaft Position. A rattling noise can be heard from the engine compartment; the engine has a loss of power; and the Service Engine Soon lamp is illuminated. One or more of the following faults may be stored. E70, E71, E82, E88, E90, E92 and E93: 2D5A - VANOS, intake: control fault, camshaft sticking 2D5B - VANOS, intake: control fault, position not reached 2D60 - VANOS, exhaust: control fault, camshaft sticking 2D61 - VANOS, exhaust: control fault, position not reached 2D9F - camshaft input sensor: signal implausible 2DA1 - Camshaft exhaust sensor: signal implausible 300C - Camshaft input sensor: signal high 300D - Camshaft input sensor: signal low 300E - Camshaft exhaust sensor: signal high 300F - Camshaft exhaust sensor: signal low F07, F10, F12, F13 and F25: 130104 - VANOS, intake: control fault, camshaft sticking 130108 - VANOS, intake: control fault, position not reached 130304 - VANOS, exhaust: control fault, camshaft sticking 130308 - VANOS, exhaust: control fault, position not reached 130E11 - Camshaft input sensor: signal implausible 130F11 - Camshaft exhaust sensor: signal implausible 164020 - Camshaft input sensor: signal high 164021 - Camshaft input sensor: signal low 164030 - Camshaft exhaust sensor: signal high 164031 - Camshaft exhaust sensor: signal low CAUSE One or both (intake and/or exhaust) of the VANOS gear assemblies have failed; the attaching bolts may have also loosened and/or broken.

NHTSA · bulletin constructeur10149339Années modèle 2011Affiché en anglais d’origine · traduction en attenteVoir le détail →
F80 M3 · 2014–2018
BulletinModéréÉlectroniqueNA

Bulletin

2013 MINI JCW Paddle Shifter Retrofit. SZL to EGS harness installation. For necessary preliminary tasks, refer to ISTA and perform the following steps listed in this document.

NHTSA · bulletin constructeur10149498Affiché en anglais d’origine · traduction en attenteVoir le détail →
E90/92/93 M3 · 2007–2013
BulletinModéréÉlectroniqueNA

Bulletin

N51 Engine: Service Engine Soon Lamp Illuminated - Loss of Power and Various Faults Stored in the DME. The customer complains that the Service Engine Soon lamp is illuminated. The vehicle has lost power; the engine cranks but will not start; and various faults are stored in the DME for engine misfire and/or mixture adaptations. CAUSE The vehicle has lost fuel system delivery pressure due to a loose or split fuel line inside the fuel tank. The failure is related to an unfavorable stacking of tolerances between the rubber fuel hose and the plastic regulator nipple or deterioration of the rubber hose construction material.

NHTSA · bulletin constructeur10149349Années modèle 2011Affiché en anglais d’origine · traduction en attenteVoir le détail →
E90/92/93 M3 · 2007–2013
BulletinModéréÉlectroniqueNA

Bulletin

N51, N52K, N52T and N55 Engine: Various Faults Stored in DME Related to VANOS and Camshaft Position. A rattling noise can be heard from the engine compartment; the engine has a loss of power; and the Service Engine Soon lamp is illuminated. One or more of the following faults may be stored. E70, E71, E82, E88, E90, E92 and E93: 2D5A - VANOS, intake: control fault, camshaft sticking 2D5B - VANOS, intake: control fault, position not reached 2D60 - VANOS, exhaust: control fault, camshaft sticking 2D61 - VANOS, exhaust: control fault, position not reached 2D9F - camshaft input sensor: signal implausible 2DA1 - Camshaft exhaust sensor: signal implausible 300C - Camshaft input sensor: signal high 300D - Camshaft input sensor: signal low 300E - Camshaft exhaust sensor: signal high 300F - Camshaft exhaust sensor: signal low F07, F10, F12, F13 and F25: 130104 - VANOS, intake: control fault, camshaft sticking 130108 - VANOS, intake: control fault, position not reached 130304 - VANOS, exhaust: control fault, camshaft sticking 130308 - VANOS, exhaust: control fault, position not reached 130E11 - Camshaft input sensor: signal implausible 130F11 - Camshaft exhaust sensor: signal implausible 164020 - Camshaft input sensor: signal high 164021 - Camshaft input sensor: signal low 164030 - Camshaft exhaust sensor: signal high 164031 - Camshaft exhaust sensor: signal low CAUSE One or both (intake and/or exhaust) of the VANOS gear assemblies have failed; the attaching bolts may have also loosened and/or broken.

NHTSA · bulletin constructeur10149296Années modèle 2011Affiché en anglais d’origine · traduction en attenteVoir le détail →
F80 M3 · 2014–2018
BulletinModéréÉlectroniqueNA

Bulletin

NVLD Tank Leakage FC 190302 Fuel Tank Ventilation and Purge Air System Micro Leak. The engine malfunction warning is illuminated and the following fault code is stored in the DME memory: z FC 190302 Fuel tank ventilation and purge air system micro leak leakage greater than 0_5 mm CAUSE Contamination of the NVLD pressure switch electrical contacts

NHTSA · bulletin constructeur10148173Années modèle 2015Affiché en anglais d’origine · traduction en attenteVoir le détail →
F80 M3 · 2014–2018
BulletinModéréÉlectroniqueNA

Bulletin

Service Action: Bluetooth Software (KISU Data) Update. This Service Action is being released to improve customer satisfaction as we strive to be number 1 in the JD Power Initial Quality Survey (IQS). This new KISU software improves the Bluetooth functionality in our vehicles, and it helps keep us up-to-date with technology innovation. Please implement the Bluetooth Software Update Service Action. This Service Action will be in effect until March 2015. Thank you for your continuous support. Improved KISU data (Customer Initiated Software Update) is now available for installation in these vehicles via the USB port. Improved functionality for COMBOX: z Detailed view of the text messages z Android device connection stability (linked contacts causing BT disconnection) Improved functionality for HU-H: z Reconnection strategy z 3rd Party App Metadata - Album art and song title Note: This Service Action is to be completed only at the dealer. You (dealers) will be receiving vehicles from the VDCs that will require this service action to be completed prior to customer delivery.

NHTSA · bulletin constructeur10148195Années modèle 2015Affiché en anglais d’origine · traduction en attenteVoir le détail →
F80 M3 · 2014–2018
BulletinModéréÉlectroniqueNA

Bulletin

"Service Action: Replace Engine Compartment Sound Insulation. The sound insulation in the engine compartment does not seal properly. 1.Left side: Turn the locks (1) 90 degrees counterclockwise. Unlock the catch (2) and remove the cover (3). Manufacturing tolerances and a defect in workmanship may cause the sound insulation to leak water into the DME wiring connector. AFFECTED VEHICLES This Service Action involves F80 and F82 vehicles produced from March 18, 2014 to May 20, 2014. First check if a Service Action label with a code number 698 is already attached to the B-pillar. If a code number 698 has been punched out, the Service Action has already been performed and no further action is necessary. Vehicles which require this Service Action to be completed will show it as ""Open"" when checked either in the ""Service Menu"" of DCSnet (Dealer Communication System) or with the Key Reader."

NHTSA · bulletin constructeur10148031Années modèle 2015Affiché en anglais d’origine · traduction en attenteVoir le détail →
F80 M3 · 2014–2018
BulletinModéréÉlectroniqueNA

Bulletin

N63: Proper Ignition Harness Installation and Ground Connections. INFORMATION https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/16511.1.B12241... 10/14/2014 Page 2 of 2 Any consecutive damage to the BSD interface components (DME, alternator voltage regulator, QLT sensor) caused by incorrect reinstallation of the ignition harness is not covered under the BMW New Vehicle /SAV Limited Warranty.

NHTSA · bulletin constructeur10148021Affiché en anglais d’origine · traduction en attenteVoir le détail →
F80 M3 · 2014–2018
BulletinModéréÉlectroniqueNA

Bulletin

Battery Maintenance Requirements: Battery Care. Proper battery maintenance is vital when BMW vehicles are in your center's inventory. Allowing a vehicle's battery voltage to drop below 12.0 volts (12.0V) permanently reduces the battery life expectancy and can lead to premature failure of the battery. For vehicles, equipped with a high-voltage battery (hybrid/electric vehicles), failure to properly maintain this battery may lead to a greatly discharged HV battery, requiring replacement. We provide a flexible battery maintenance system every BMW center can use in accordance with their particular needs. This bulletin explains the Battery Charging Calendar (see attachment), charging systems and a simplified tool and battery voltage checking procedure below.

NHTSA · bulletin constructeur10148035Affiché en anglais d’origine · traduction en attenteVoir le détail →
F80 M3 · 2014–2018
BulletinModéréÉlectroniqueNA

Bulletin

BMW Parts Bulletin TEC9V Fuel Tank / Level Sensor Returns BMW AG has requested an inspection of the following part numbers: 16 11 7 268 031, 16 11 7 268 032 and 16 11 7 297 340 Stock should not be sold or installed on any vehicle. 16 11 7 268 031 and 16 11 7 268 032 All fuel tanks produced before 05/30/2014 needs to be returned. All parts with later dates of production are ok and can be used. 16 11 7 297 340 All level sensors produced in Poland before 05/19/2014 (date is shown as day 139 of year 14 on the part) need to be returned. Those produced after this date are ok and can be used. All level sensors produced in Brazil currently in dealer inventory need to be returned. Please return all part(s) to your facing Regional Distribution Center (RDC). Submit for return using a YR26 damage claim with order reason BM2. A valid BMW delivery and delivery item number must be entered, and TEC9V must appear in the text of your TEC claim. TEC9V is valid from September 24, 2014, through October 08, 2014. The deadline for filing a claim under TEC9V is October 08, 2014. All parts must be returned to your facing RDC no later than October 22, 2014. Please re-order the same part numbers as needed. (c) 2014, BMW of North America, LLC. The contents of this document are confidential and should not be shared with third parties for distribution. Page 2 / 2 Made in Poland Made in Brazil Need to be returned (c) 2014, BMW of North America, LLC. The contents of this document are confidential and should not be shared with third parties for distribution.

NHTSA · bulletin constructeur10148044Affiché en anglais d’origine · traduction en attenteVoir le détail →
Plus anciens →

Sources : NHTSA (États-Unis, domaine public), Transports Canada (Licence du gouvernement ouvert – Canada), DVSA (Royaume-Uni, Open Government Licence v3.0), RappelConso et Safety Gate de l'UE (France, Licence Ouverte 2.0), MLIT (Japon, licence de données publiques 1.0) et MOLIT (Corée du Sud, car.go.kr).