Les bulletins techniques (TSB) sont des instructions de réparation que les constructeurs envoient à leurs concessionnaires sur des problèmes connus. Ce ne sont pas des rappels de sécurité, mais ils confirment souvent un défaut.
Some 2021 Escape vehicles built on or before 9-Feb-2021 may exhibit a "Tire Mobility" message in the message center. This may be due to the software in the instrument panel cluster (IPC). To correct the condition, download and run the "IPC Instrument Panel Cluster (IPC) Configuration" application in the Ford Diagnostic and Repair System (FDRS) scan tool. If asked if the original module is still installed, answer NO. For claiming, use causal part 10849 and labor operations 12651D and 12651D4.
NHTSA · bulletin constructeur11028167Années modèle 2021Affiché en anglais d’origine · traduction en attenteVoir le détail →
Il s'agit d'un programme d'enquête proactif mené par Ford Motor Company afin d'inspecter un nombre limité de véhicules concernés appartenant à des clients. Ford mène ce programme de manière volontaire afin d'évaluer le logiciel actuellement installé sur un ou plusieurs modules électroniques des véhicules concernés.
NHTSA · bulletin constructeur11026013Années modèle 2014Traduit automatiquement · original : anglaisVoir le détail →
Some 2024-2025 Escape Hybrid/Maverick Hybrid/Nautilus Hybrid/F-150 non-Lightning/F-Super Duty/Bronco and 2025 Expedition/Navigator/Ranger vehicles where customers have installed an aftermarket supplemental braking system may experience a discharged 12-volt battery after recreational towing. This may be due to the supplemental braking system keeping the vehicle awake during brake applications. Advise customers that while recreational towing the vehicle with a supplemental braking system installed, it is recommended to use a 12-volt battery charger connected to a power source external to the vehicle being towed. The Owners Manual is in process of being updated with this information.
NHTSA · bulletin constructeur11023567Années modèle 2024Affiché en anglais d’origine · traduction en attenteVoir le détail →
Some 2025 Escape vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P0073 stored in the powertrain control module (PCM) and/or B1B38 stored in the body control module (BCM). The vehicle may also exhibit no ambient air temperature reading shown in the instrument panel cluster (IPC) and/or center display screen. This may be due to a pinched, chafed, or severed wiring harness 15K867. To inspect the suspect area of the harness for damage, turn the steering wheel to the left and remove the four lower push pins from the front passenger side fender liner. Gently fold the liner inward and visually inspect the visible portion of harness 15K867 below the passenger side headlamp and follow the harness down behind the visible parts behind the front parking aid sensors.
NHTSA · bulletin constructeur11023205Années modèle 2025Affiché en anglais d’origine · traduction en attenteVoir le détail →
Certain 2025 Model Year Corsair and Escape equipped with a panoramic roof Roof Opening Panel Rear Trim Inspection and Replacement Dealers are to inspect the serial number of the moonroof assembly to determine if it is within the suspected build range. If the vehicle has a suspected leaking Roof Opening Panel Rear Trim piece based on the serial number, the Roof Opening Panel Rear Trim piece will be removed and replaced per the standard Workshop Manual procedure. This service must be performed on all affected vehicles at no charge to the vehicle owner.
NHTSA · bulletin constructeur11021205Années modèle 2025Affiché en anglais d’origine · traduction en attenteVoir le détail →
* This article supersedes TSB 23-2428 to update the service procedure and update labor times from actual time to actual time with a limit. Some of the vehicles listed in the Model statement above may exhibit one of the following conditions: * Multiple illuminated warning indicators displayed in the instrumental panel cluster (IPC): - Anti-lock brake system (ABS) warning indicator - Parking brake (red) indicator - Brake warning indicator - Parking brake (yellow) warning indicator - Parking brake (red) indicator - Stability-traction control indicator * Intermittent no crank/no start condition * Various lost communication diagnostic trouble codes (DTCs) stored in various modules. This may be due to the software installed in the ABS module.
NHTSA · bulletin constructeur11019424Années modèle 2023Affiché en anglais d’origine · traduction en attenteVoir le détail →
2023 Escape vehicles equipped with a 2.5L PHEV powertrain may exhibit a condition where the DTE display (gas) disappears from the IPC. This may be due to the software installed in the IPC.
NHTSA · bulletin constructeur11010612Années modèle 2023Affiché en anglais d’origine · traduction en attenteVoir le détail →
Some 2024 Bronco Sport/Escape and 2025 Explorer vehicles may have been ordered with a DIO Securicode RKE wired keypad that requires installation and enabling by the dealer prior to delivery.
NHTSA · bulletin constructeur11007968Années modèle 2024Affiché en anglais d’origine · traduction en attenteVoir le détail →
Some 2024 Bronco Sport/Escape and 2025 Explorer vehicles may have been ordered with a DIO Securicode RKE wired keypad that requires installation and enabling by the dealer prior to delivery.
NHTSA · bulletin constructeur11006802Années modèle 2024Affiché en anglais d’origine · traduction en attenteVoir le détail →
Quality improvements include: - Correct navigation/turn-by-turn indication in Instrument Cluster while entering a roundabout. - Gas DTE (Distance To Empty) indication appears continuously when scrolling through all Info on Demand screens. - HMI animation refinements - Eliminates single gauge flicker in ignition off. - Enlarged graphics displayed for ""keep hands on steering wheel"" message.
NHTSA · bulletin constructeur11003272Années modèle 2023Affiché en anglais d’origine · traduction en attenteVoir le détail →
Some 2023 Escape/Corsair vehicles built on or before 27-Nov-2023 equipped with 1.5L/2.0L engines may exhibit a harsh engagement after auto start/stop feature restarts the engine. This may be due to the software installed in the anti-lock brake (ABS) module. To correct this condition, reprogram the ABS module using the latest software level of the Ford Diagnosis and Repair System (FDRS). For claiming use causal part number 2C219 and the applicable labor operations in Section 02 of the Service Labor Time Standards (SLTS) Manual.
NHTSA · bulletin constructeur11003137Années modèle 2023Affiché en anglais d’origine · traduction en attenteVoir le détail →
Software Update 23-PU0630-SX2-CLS for 2023 MY Escape vehicles is now available. Quality Improvements include: - SYNC screen will update after changing to next track from USB device. - Improves minor occurrence of gauge flicker once in ignition "off". - Enlarges graphic for "keep hands on steering wheel" message - Robustness fixes for error handling, menu browsing, navigation and audio repeaters.
NHTSA · bulletin constructeur10254303Années modèle 2023Affiché en anglais d’origine · traduction en attenteVoir le détail →
Software Update 24-PU0122--SPB-PUP for 2023 MY Escape Gas vehicles is now available. Quality Improvements include: - Reduced no start events. - Quicker brake release when customer shifts to R - Remembers Auto Vehicle Hold status thru key cycle - Warning lamp for park brake stuck event. - Message when shift to neutral occurs with driver off brakes. - Will no longer set erroneous "Service Park Brake Limited Function" during initialization.
NHTSA · bulletin constructeur10251482Années modèle 2023Affiché en anglais d’origine · traduction en attenteVoir le détail →
Some 2023 Escape/Corsair vehicles built on or before 07-Sep-2023 may exhibit an intermittent no crank/no start condition with various lost communication diagnostic trouble codes (DTCs) stored in various modules and multiple illuminated warning indicators such as: anti-lock brake system (ABS) warning indicator, parking brake (red) indicator, brake warning indicator, parking brake (yellow) warning indicator and/or parking brake (red) indicator and/or stability-traction control indicator displayed in the instrumental panel cluster (IPC). To correct this condition, follow the Service Procedure to reprogram various modules starting with the PCM.
NHTSA · bulletin constructeur10251457Années modèle 2023Affiché en anglais d’origine · traduction en attenteVoir le détail →
Some 2023 Escape vehicles with hybrid powertrain built on or before 27-Oct-2023 and 2023 Corsair vehicles with hybrid powertrain built on or before 24-Oct-2023 may exhibit an intermittent no audio condition with diagnostic trouble code (DTC) U1A00:87 stored in the accessory protocol interface module (APIM). When the audio volume control is adjusted using the steering wheel or the center display screen, the center display screen may or may not show a visual change with no change in audio volume. This may be due to the software installed in the audio control module (ACM). To correct this condition, reprogram the ACM using the latest software level of the Ford Diagnosis and Repair System (FDRS) diagnostic tool. For claiming, use causal part 18C869 and applicable labor operation in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA · bulletin constructeur10250523Années modèle 2023Affiché en anglais d’origine · traduction en attenteVoir le détail →
Some 2023 Escape vehicles may exhibit a Front Camera Fault and/or Pre-Collision Assist Fault message displayed in the instrumental panel cluster (IPC) with diagnostic trouble codes (DTCs) C1001:78 and U2107:68 stored in the image processing module-A (IPMA) when the vehicle is driven on uneven roads. This may be due to the software installed in the IPMA. To correct this condition, reprogram the IPMA using the latest software version of the Ford Diagnosis and Repair System (FDRS) scan tool and perform the appropriate IPMA alignment procedure. Perform a self test and clear DTC codes. For claiming, use causal part 14G647 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA · bulletin constructeur10250308Années modèle 2023Affiché en anglais d’origine · traduction en attenteVoir le détail →
Software Update SU6 P1 for 2023 MY Escape vehicles is now available. Quality Improvements include: - Removal of BlueCruise map expiration - Allow Vehicle entry during OTA. - Adds a "some display features may be temporarily unavailable" message to the SYNC screen when a SYNC update is installing. -Addresses SYNC reboot issue may occur after 2 hours of continuous use.
NHTSA · bulletin constructeur10249821Années modèle 2023Affiché en anglais d’origine · traduction en attenteVoir le détail →
Some 2023 Escape vehicles equipped with a head up display (HUD) built on or before 16-Oct-2023 may exhibit a condition where the speed limit sign indicator is not displayed in the HUD. This may be due to the software installed in the HUD module.
NHTSA · bulletin constructeur10249788Années modèle 2023Affiché en anglais d’origine · traduction en attenteVoir le détail →
Some 2023 Escape/Corsair vehicles built on or before 07-Sep-2023 may exhibit an intermittent no crank/no start condition with various lost communication diagnostic trouble codes (DTCs) stored in various modules and multiple illuminated warning indicators such as: anti-lock brake system (ABS) warning indicator, parking brake (red) indicator, brake warning indicator, parking brake (yellow) warning indicator and/or parking brake (red) indicator and/or stability-traction control indicator displayed in the instrumental panel cluster (IPC). This may be due to the software in the ABS module. To restart the vehicle, allow the vehicle to be powered off for more than 10 minutes and attempt a restart. This condition does not affect vehicle durability and no additional diagnosis or service is required for this condition at this time. Inform customers that they can continue to drive the vehicle and engineering is currently working on a solution for this condition that is expected in February 2024. Replacement or reprogramming of the ABS module will not resolve this condition. Monitor OASIS for additional information
NHTSA · bulletin constructeur10248999Années modèle 2023Affiché en anglais d’origine · traduction en attenteVoir le détail →
Some 2023 Escape/Corsair vehicles built on 6-Apr-2023 and through 11-May-2023 and 2023 Bronco Sport/Maverick vehicles built on 30-Jan-2023 and through 6-Jun-2023 may exhibit an illuminated air bag warning indicator with DTC B0082:1A stored in the restraints control module (RCM). This may be due to an issue with the passenger seatbelt retractor at connector C303B. If a connection issue is found, replace the passenger front seatbelt retractor and pretensioner assembly before attempting a wiring repair. This issue does not affect the proper operation of the air bags, retractor and pretensioner. Refer to the Workshop Manual (WSM), Section 501-20A Seatbelt Systems > Removal and Installation. For claiming, use causal part 78611B08 and applicable labor times in Section 12 of the Service Labor Time Standards (SLTS) Manual.
NHTSA · bulletin constructeur10244854Années modèle 2023Affiché en anglais d’origine · traduction en attenteVoir le détail →
Some 2023 Escape, Corsair, Bronco Sport and Maverick vehicles built on 01-May-2023 and through 22-Sep-2023 may exhibit a squeal and/or grinding noise and/or vibration from the front brakes while braking. This may be due to excessive wheel hub lateral runout. To correct this condition, remove the front brake disc(s) of the affected wheel(s). Refer to the Workshop Manual (WSM), Section, 206-03. Clean the raised ring-like surface of the front wheel hub near the wheel studs. Using a dial indicator, slowly rotate the wheel hub and measure the runout on the ring-like surface. If the total runout exceeds 0.001 inch (0.03mm), replace the wheel hub. Refer to the WSM, Section 204-01. Document the measured run out in the warranty claim. For claiming use the causal part number 1104 and applicable labor operations in Section 01 of the Service Labor Time Standards (SLTS)
NHTSA · bulletin constructeur10243653Années modèle 2023Affiché en anglais d’origine · traduction en attenteVoir le détail →
Some 2021-2023 Ford and Lincoln vehicles may exhibit DTCs U2100 and/or U3002 stored in the cruise control module (CCM), side obstacle detection control module LH (SODL), side obstacle detection control module RH (SODR), side obstacle detection control module C (SODCMC) and/or side obstacle detection control module D (SODCMD) after a module replacement. DTC U2100 may set when the module has not been properly configured after replacement. DTC U3002 may set when the module has been configured with the incorrect VIN. To correct this condition, verify that the module storing the DTC has been installed following the applicable Workshop Manual (WSM) Removal and Installation procedure. If the DTC is still stored, download and run the Vehicle Identification Number (VIN) Write application found under Toolbox, Multi-Module tab in the Ford Diagnosis and Repair System (FDRS).
NHTSA · bulletin constructeur10243479Années modèle 2023Affiché en anglais d’origine · traduction en attenteVoir le détail →
Some 2023 Escape vehicles built on or before 6-May-2023 may exhibit a condition where the power liftgate does not close when using the power liftgate control switches. The vehicle may exhibit diagnostic trouble codes B1454 and/or B1455. Prior to following Workshop Manual (WSM) diagnostic procedures, remove the liftgate left/right/center upper trim panels. Refer to WSM, Section 501-05 Interior Trim and Ornamentation > Removal and Installation. Disconnect C4173 and C4172 and verify the resistance of the anti-pinch switches. Refer to the Wiring Diagram, cell 109. If the resistance is below 5.58K ohms, replace the affected switch(s). If both anti-pinch switches measure above specification, perform a power liftgate initialization and re-evaluate the concern. Refer to WSM, Section 501-03 Body Closures > General Procedures.
NHTSA · bulletin constructeur10237796Années modèle 2023Affiché en anglais d’origine · traduction en attenteVoir le détail →
Some 2022-2023 F-150/Bronco/Expedition/Navigator/Escape/Corsair/Bronco Sport/Edge/Mustang vehicles built on 04-Sep-2022 and through 30-Dec-2022 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0230 stored in the powertrain control module (PCM). The vehicle may also experience a no start or stall after start. This may be due to an internal PCM issue. If this DTC is present, verify the battery condition, then perform pin point test (PPT) KC of the Work Shop Manual (WSM), Section 310-01. If PPT KC leads to component replacement, start with replacing the PCM and then evaluate the vehicle. If the DTC returns, follow WSM, Section 310-01 PPT KC direction to address the issue.
NHTSA · bulletin constructeur10237335Années modèle 2023Affiché en anglais d’origine · traduction en attenteVoir le détail →
Sources : NHTSA (États-Unis, domaine public), Transports Canada (Licence du gouvernement ouvert – Canada), DVSA (Royaume-Uni, Open Government Licence v3.0), RappelConso et Safety Gate de l'UE (France, Licence Ouverte 2.0), MLIT (Japon, licence de données publiques 1.0) et MOLIT (Corée du Sud, car.go.kr).