Bulletin
Rough idle, rolling idle, stall, high idle, or back fire mainly after a cold start. Also hesitation or surge at steady cruise, or malfunction indicator lamp (mil) illuminated condition. *tt *jb
🔔 Créez un compte gratuit pour recevoir les alertes e-mail sur Ford Focus (toutes les générations)
Les bulletins techniques (TSB) sont des instructions de réparation que les constructeurs envoient à leurs concessionnaires sur des problèmes connus. Ce ne sont pas des rappels de sécurité, mais ils confirment souvent un défaut.
Rough idle, rolling idle, stall, high idle, or back fire mainly after a cold start. Also hesitation or surge at steady cruise, or malfunction indicator lamp (mil) illuminated condition. *tt *jb
Certain 2014-2020 Model Year Multiple Vehicle Lines 3G Telematics Control Unit to 4G Upgrade Kit REASON FOR THIS SUPPLEMENT Program Terms & Urgency / Expiration Date: Program extension until July 31, 2023. Service Action: o IDS level 128 or higher is now required to address various programming issues encountered. o C-MAX Energi vehicles are now serviceable with new software and hardware. Labor Allowances: C-MAX labor has been updated. Parts Requirements / Ordering Information: o The C-MAX 4G Upgrade Kit is now orderable at this time with a new part number. o MKX Rear seat backrest nut claim quantity updated. Technical Information updates: o Ensure IDS level 128 or higher is used. o Toggling Valet Mode is no longer required. o C-MAX Energi instructions are now available. Owner Notification: Non-repaired vehicle owners will be mailed the week of April 17, 2023. Pickup and Delivery: Added Customer Acknowledgement Form - Review form contents with customer prior to kit ordering and obtain customer signature prior to installation for Focus BEV, C-MAX, and Fusion Energi vehicles.
2017 vehicles equipped with a 2.0L GTDI, 2.3L GTDI, or 2.5L PFI engine will either be equipped with a diamond washer on each side of a smooth-faced crankshaft timing sprocket (early build), or a crankshaft timing sprocket with laser etched faces and no diamond washers (late build). If equipped, diamond washers should be cleaned, inspected and reused, if undamaged. Diamond washers should never be installed along with a laser etched crankshaft timing sprocket. Related WSM procedure information is in the process of being updated.
Some 2016-2017 Ford/Lincoln vehicles SYNC 3 may exhibit an intermittent blank screen. Check for SYNC software update under the OASIS Tab SYNC selection. If update is available refer to WSM, Section 415-00 and update APIM software. During the update process the SYNC status bar shows Updating System Software for approximately 30 minutes. After Installation Complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or blank screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
Some Focus Vehicles built on or after 21-Jul-2016 thru 15-Sep-2016 equipped with the DPS6 Transmission exhibiting concerns of shift quality may have an incorrectly aligned clutch actuator spring retainer (7515). While performing transmission or clutch repair on vehicles within these date ranges please Refer to Works Shop Manual (WSM) 307-01A Removal and Installation, Clutch Actuator for proper installation and alignment of these Spring Retainers.
Some 2017 Focus vehicles equipped with 1.0L Gasoline Turbo Direct Injection (GTDI) engines built on 27-Feb-2017 and through 12-Apr-2017 may exhibit excessive engine idle vibrations. Inspect the engine torque restrictor installed part numbers. Automatic transmission equipped vehicles, should have BV61-6P082-CB installed. Manual transmission vehicles should have CV61-6P082-DC installed. Refer to Workshop Manual (WSM), Section 303-08 for remove instructions. For claiming, use causal part 6068 and applicable labor operations in section 06-Engine of the service labor time standards (SLTS) manual.
Some 2016 focus vehicles may not successfully complete reprogramming or programmable module installation (pmi) of the bcm. Make certain the integrated diagnostic system (ids) is at release 103.03 or higher before attempting bcm programming.
Ford: At low speed driving or parking lot maneuver, vehicle may experience low power steering assist and this condition can be reprogrammed to latest calibration software. Model 2013 focus. *pe
Ford: On some vehicles, stored in diagnostic trouble code (dtc) p260 (engine off timer performance), resulting in slow network communication with cluster or insurance monitoring devices installed in vehicle onboard diagnostic trouble code. Model 2014 focus, fiesta. *pe
Ford: On some vehicles, diagnostic trouble codes (dtcs) are stored in powertrain control module memory, and using remote start feature, would have crank no start or stall, shortly after vehicle has been driven. Models 2013 c-max, focus, escape. *pe
Ford: See document search button for owner letter. During testing, active grille shutter (ags) wire harness electrical terminals was damaged, and causes engine temperature to rise, if louvers are closed and open circuit occurs, whereby warning light illuminates, chime will sound and high engine temperature, stop safely message is displayed. Model 2012 focus. *pe
Ford: See document search button for owner letter. Vehicle experience roll back when transitioning to accelerator pedal from brake pedal while on incline. Transmission would be jerky or rough when shifting. Pe
Ford: Some vehicles may exhibit a steering wander at highway speeds over 72 km/h (45 mph). Customers may indicate they have to frequently adjust the steering wheel slightly to maintain the direction of travel. *js
Ford: See document search button for owner letter. Certain model year vehicles have an improperly balanced clutch assembly. This will cause a vibration felt through the seat and/or steering will while in park, first gear and neutral position. *pe
Ford: There may be steering assist warning lights as well as well as a stored trouble code. 2012 focus. *rm
Ford : Klaxon inopérant. Lors du diagnostic de véhicules présentant un klaxon inopérant (numéro de pièce de base 13832), vérifier le bon positionnement et la bonne installation du coussin gonflable conducteur/de la plaque de klaxon. Si la plaque de klaxon est mal positionnée ou mal installée, cela peut provoquer l'activation continue du klaxon, ce qui l'endommage. *pe
Ford: Some vehicles may exhibit a parts no crank/no start condition with diagnostic trouble codes 9dtc) p1260 in the powertrain control module (pcm) and u0100 in the instrument cluster (ic). *pe
Increased brake pedal efforts required on initial stopping after cold start at high altitude. *tt
Crank no start or hard start cold. *tt
Crank no start or other driveability concerns - service tip. *tt
Diagnostic trouble code (dtc) p0068, intermittent crank no start, and hesitation/surge at 120 km/h (75 mph). *tt
Rough, rolling, or high idle or stall - mainly after cold start, engine - intake separation at rubber boots - svt models only. *tt
Some vehicles may exhibit a crank / no start, poor idle, and / or lack of power, with camshafts out of time. *tt
Informations concernant un démarrage impossible dû à un arbre à cames grippé. *yh
Subject regarding body-rear liftgate spoiler- removal and installation tips. *jg
Sources : NHTSA (États-Unis, domaine public), Transports Canada (Licence du gouvernement ouvert – Canada), DVSA (Royaume-Uni, Open Government Licence v3.0), RappelConso et Safety Gate de l'UE (France, Licence Ouverte 2.0), MLIT (Japon, licence de données publiques 1.0) et MOLIT (Corée du Sud, car.go.kr).