Les bulletins techniques (TSB) sont des instructions de réparation que les constructeurs envoient à leurs concessionnaires sur des problèmes connus. Ce ne sont pas des rappels de sécurité, mais ils confirment souvent un défaut.
This bulletin supersedes the previously issued bulletin(s) listed below. The changes are noted in Red. 09-012/21 12/13/21, 06/10/21 and 04/27/21 DESCRIPTION Some customers may experience all of following symptoms: The door lock/unlock operation will not work using the remote transmitter button. 1. The door lock/unlock operation will not work using the door lock/release touch sensor. 2. The engine will not start using the ignition switch. 3. The transmitter operates by itself. 4. The key battery drains faster than usual. 5. Symptoms 1-3: This may be caused when excess load is applied to the remote transmitter, deforming the electrical terminals and creating poor contact with the battery. To eliminate this concern, the structure in the remote transmitter has been modified to reduce the deformation of the electrical terminals. Symptom 4-5: This may be caused when excessive load is applied to the remote transmitter, creating a gap around the gasket where moisture enters and corrodes the circuit board which in turn drains the key battery faster than usual. To eliminate this concern, the thickness of the case wall on the gasket mounting surface has been increased and the bonding strength of the components has been improved to prevent deformation. REPAIR PROCEDURE If the battery is bad or installed incorrectly, replace the battery and/or install it correctly. If the remote power saving function is off and the battery is good and installed correctly, replace the defective remote transmitter with a modified one according to the instructions on MGSS (IMMOBILIZER SYSTEM-RELATED PARTS PROGRAMMING). NOTE: DO NOT replace other remote transmitter(s) for the vehicle if they not experiencing an issue.
NHTSA · bulletin constructeur11034436Années modèle 2021Affiché en anglais d’origine · traduction en attenteVoir le détail →
Some customers may experience the following symptoms of the wireless charger (Qi), even when the mobile device (smartphone etc.) is placed in the proper position on the wireless charger (Qi). It does not start charging. It stops charging with the indicator flashing in red after starting. It stops charging without any visible sign after starting. For CX-50, some customers may experience that despite placing the MagSafe-equipped iPhone at the center of the wireless charger, charging stops after about ten seconds. MagSafe-equipped iPhones use magnets to align the charger and the device. When charging MagSafe-equipped iPhones with a non-MagSafe compatible charger, improper alignment can cause the magnetic field required for charging to be disrupted by the magnets, significantly reducing charging efficiency.
NHTSA · bulletin constructeur11012342Années modèle 2021Affiché en anglais d’origine · traduction en attenteVoir le détail →
MNAO has recently found an increase in non-returned cores within the United Radio (UR) exchange program. As a reminder, dealers have 90 days, after the order is placed, to return the exchanged part. Failure to return the exchanged part will result in a debit of the full component price. It is highly recommended to set a calendar reminder at the time of the order for no more than 60 days to ensure all orders are returned if repaired and if not repaired, contact the customer to cancel the order and return the unit.
NHTSA · bulletin constructeur10243559Années modèle 2021Affiché en anglais d’origine · traduction en attenteVoir le détail →
Some customers may experience the following symptoms of the wireless charger (Qi), even when the mobile device (smartphone etc.) is placed in the proper position on the wireless charger (Qi). - It does not start charging. - Soon after starting, it stops charging with the indicator flashing in red. - Soon after starting, it stops charging without any visible sign. These symptoms may be caused by improper control software of the wireless charger (Qi). To eliminate these concerns, the specification of the wireless charger (Qi) has been modified. NOTE: The modifications for the symptoms are different depending on the model.
NHTSA · bulletin constructeur10243549Années modèle 2021Affiché en anglais d’origine · traduction en attenteVoir le détail →
Certains véhicules peuvent présenter une perte de puissance et le voyant de contrôle moteur allumé, avec le code DTC P061B:00 enregistré dans la mémoire du PCM, dans l'une des conditions suivantes (A ou B). - DTC P061B:00 - [PCM] Problème de performance du calcul de couple du module de commande interne. Condition Condition Description A Lorsque le démarrage est interrompu (se produit probablement lorsque la pédale de frein est relâchée pendant le démarrage) B Lors d'une accélération entre 1300 et 1600 tr/min avec papillon grand ouvert
En raison d'une logique de commande incorrecte du PCM, la détection des erreurs de calcul du couple moteur est trop sensible. Pour éliminer ce problème, le logiciel du PCM a été modifié.
NHTSA · bulletin constructeur10218722Années modèle 2019Traduit automatiquement · original : anglaisVoir le détail →
When installing a navigation SD card, confirm that the card is unlocked. Also, Mazda Does Not Recommend swapping navigation system SD cards from one vehicle to another for testing. If swapped, the SD card that is installed into the other vehicle becomes linked to the VIN of that vehicle.
NHTSA · bulletin constructeur10185967Années modèle 2016Affiché en anglais d’origine · traduction en attenteVoir le détail →
Some vehicles may experience a Tire Pressure Monitoring System (TPMS) warning light improperly illuminates when driving on a smooth road surface even if the TPMS system has been properly initialized at the specified tire air pressure. Please contact the Hotline for a countermeasure repair if a vehicle arrives with this issue. A countermeasure control module is due in July for this concern.
NHTSA · bulletin constructeur10185959Années modèle 2016Affiché en anglais d’origine · traduction en attenteVoir le détail →
Some vehicles may experience one of the following 2 symptoms, even though the windshield is clear. Under certain driving conditions, the Forward Sensing Camera (FSC) may detect a dirty windshield (not clear). NOTE FOR CUSTOMER: The FSC may not work properly under the conditions: The windshield is not clear. The FSC lens is not clear. Driving in heavy rain, dense fog or snow, or into the sun. Driving on a road with no or blurred road lane markings. When the windshield becomes foggy in the winter time or other cold weather conditions and LDWS/HBC warning lights turn on, drive with the defroster on for about 10 minutes. This will help clear the foggy windshield at the FSC.
NHTSA · bulletin constructeur10185957Années modèle 2016Affiché en anglais d’origine · traduction en attenteVoir le détail →
Some vehicles may exhibit a knocking / squeaking noise from the front shock absorber when driving on rough roads and/or when turning the steering wheel while the vehicle is stopped.
NHTSA · bulletin constructeur10185907Années modèle 2016Affiché en anglais d’origine · traduction en attenteVoir le détail →
A/C blows warm air. Some customers may complain about warm air from the climate cointrol vents. This may be caused by improper brazing (A) of the evaporator (B) causing a refrigerant leak fr om the joint between the tubes and the header (D)
NHTSA · bulletin constructeur10186252Années modèle 2016Affiché en anglais d’origine · traduction en attenteVoir le détail →
A/C blows warm air. Some customes may complain about warm air from the climate control vents. This may be caused by condenser corrosion, causing a refrigerant leak.
NHTSA · bulletin constructeur10185803Années modèle 2016Affiché en anglais d’origine · traduction en attenteVoir le détail →
If you experience issues with the current version of ID's such as missing tools or modules not showing after completing a network test, be advised that we are aware of these issues and are working to resolve them. As a counter measure, it is advised that you un-install ids and re-install version 103.00 and "do not update" until further notice.
NHTSA · bulletin constructeur10185813Années modèle 2017Affiché en anglais d’origine · traduction en attenteVoir le détail →
On May 1, 2018, Japan produced vehicles starting using 17 mm hex lug nuts instead of 21 mm on the same size thread. When installing new lug nuts or the accessory Wheel Lock Set, make sure to use the appropriate part number for the vehicle you are working on. NOTE: The Mazda3 produced in Mexico is not affected. Use the GEPC or the Mazda Accessory web site [MXConnect (dealers.mazdausa.com)] to look up the correct part number for the vehicle you are working on.
NHTSA · bulletin constructeur10168119Années modèle 2019Affiché en anglais d’origine · traduction en attenteVoir le détail →
On May 1, 2018, Japan produced vehicles starting using 17 mm hex lug nuts instead of 21 mm on the same size thread. When installing the accessory locking lug nuts, make sure to use the appropriate part number for the vehicle you are working on.
NHTSA · bulletin constructeur10159199Années modèle 2019Affiché en anglais d’origine · traduction en attenteVoir le détail →
On May 1, 2018, Japan produced vehicles starting using 17 mm hex lug nuts instead of 21 mm on the same size thread. When installing new lug nuts or the accessory Wheel Lock Set, make sure to use the appropriate part number for the vehicle you are working on.
NHTSA · bulletin constructeur10159196Années modèle 2019Affiché en anglais d’origine · traduction en attenteVoir le détail →
Some customers may experience a SBS/SCBS, LAS/LDWS and/or HBC warning light on. A system error message may also be found in the center display. DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction).Master Warning Light, Smart Brake Support/Smart City Brake Support (SBS/SCBS) Indicator Light, Lane-keep Assist System (LAS) Lane Departure Warning System (LDWS) Warning Light, High Beam Control (HBC) system Warning Light (amber). DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction) is stored in the FSC module and cannot be erased. This concern may be caused by a hardware failure of an internal device of the FSC, which results in a malfunction detection. To eliminate this concern, the production process of the FSC has been modified.
NHTSA · bulletin constructeur10155440Années modèle 2018Affiché en anglais d’origine · traduction en attenteVoir le détail →
Objet : Programme de service Mazda (MSP) 53. 2019 CX-3 et 2018-2019 MX-5 avec système de surveillance directe de la pression des pneus (TPMS) – Activation du système d'alarme antivol pendant la conduite
Mazda Motor Corporation a décidé de réaliser un programme de service Mazda (MSP) sur certains véhicules CX-3 2019 produits du 27 février 2018 au 12 octobre 2018 et sur certains véhicules MX-5 2018-2019 produits du 3 octobre 2017 au 15 octobre 2018. Sur certains véhicules concernés équipés du TPMS direct (le capteur TPMS de roue est monté directement sur chaque roue), le système d'alarme antivol peut s'activer pendant la conduite, le klaxon peut retentir par intermittence et les feux de détresse peuvent clignoter. Le défaut d'alarme antivol cesse après avoir coupé puis remis le contacteur d'allumage. Aucun DTC n'est enregistré.
Action requise : à partir d'aujourd'hui, reprogrammer le module de commande de carrosserie (BCM) avec la dernière calibration à l'aide de MMDS pour tous les véhicules CX-3 et MX-5 concernés en stock chez le concessionnaire, ainsi que lorsque les clients amènent leur véhicule pour un entretien ou tout autre travail de service/garantie. Les véhicules concernés ne doivent pas être livrés aux clients tant que la réparation du MSP53 n'est pas terminée. Veuillez informer le client que le BCM sera reprogrammé avec la dernière calibration, gratuitement. Si un véhicule est vendu avec un MSP53 non réalisé, votre demande de garantie PDI étape 3 fera l'objet d'un débit.
NHTSA · bulletin constructeur10154528Années modèle 2019Traduit automatiquement · original : anglaisVoir le détail →
On certain subject vehicles, it is possible that the panic alarm system may activate while driving, and the horn may sound intermittently and hazard warning lights may flash. The panic alarm concern will stop after cycling the ignition switch off, then on again. No DTCs are stored. Some TPMS wheel sensor IDs on the concerned vehicle or other vehicles nearby may cause the error in the body control module (BCM). Air pressure data transmitted from the wheel sensors may be recognized by the BCM as if the panic button on the remote transmitter has been pressed.
NHTSA · bulletin constructeur10154531Années modèle 2019Affiché en anglais d’origine · traduction en attenteVoir le détail →
Some customers may experience a SBS/SCBS, LAS/LDWS and/or HBC warning light on. A system error message may also be found in the center display. DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction). DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction) is stored in the FSC module and cannot be erased. This concern may be caused by an internal FSC failure. To eliminate this concern, the production process of the FSC has been modified.
NHTSA · bulletin constructeur10154454Années modèle 2018Affiché en anglais d’origine · traduction en attenteVoir le détail →
As of May 1, 2018, Japan produced vehicles use 17 mm hex lug nuts instead of 21 mm on the same size thread. When installing new lug nuts or the accessory Wheel Lock Set, make sure to use the appropriate part number for the vehicle you are working on. NOTE: The Mazda3 produced in Mexico is not affected.Use the GEPC or the Mazda Accessory web site [MXConnect (dealers.mazdausa.com)] to look up the correct part number for the vehicle you are working on.
NHTSA · bulletin constructeur10153226Années modèle 2019Affiché en anglais d’origine · traduction en attenteVoir le détail →
On May 1, 2018, Japan produced vehicles starting using 17 mm hex lug nuts instead of 21 mm on the same size thread. When installing the accessory locking lug nuts, make sure to use the appropriate part number for the vehicle you are working on.
NHTSA · bulletin constructeur10153304Années modèle 2019Affiché en anglais d’origine · traduction en attenteVoir le détail →
Some vehicles may experience a lack of power and the check engine light on with DTC P061B:00 and U0401:00 stored in the PCM memory when engine cranking is interrupted and on A/T vehicles, DTC U0442:00 is also stored. This concern most likely occurs when the brake pedal is released during engine cranking. DTC P061B:00 - [PCM] Internal control module torque calculation performance problem. DTC U0401:00 - Signal error from PCM DTC U0442:00 - [TCM] Invalid data received from PCM. Due to an improper control logic of the PCM, the engine torque calculation error detection is too sensitive. To eliminate this concern, the PCM software has been modified.
NHTSA · bulletin constructeur10148004Années modèle 2019Affiché en anglais d’origine · traduction en attenteVoir le détail →
Some vehicles may experience a check engine light on and/or failsafe with DTC P061B:00 stored in the PCM. This condition will likely occur as a result of one of the following causes: Engine cranking was interrupted by releasing the brake pedal. Start button was double pressed while the engine was still cranking. A countermeasure to correct mis-detection is currently being prepared.
NHTSA · bulletin constructeur10144336Années modèle 2019Affiché en anglais d’origine · traduction en attenteVoir le détail →
Sources : NHTSA (États-Unis, domaine public), Transports Canada (Licence du gouvernement ouvert – Canada), DVSA (Royaume-Uni, Open Government Licence v3.0), RappelConso et Safety Gate de l'UE (France, Licence Ouverte 2.0), MLIT (Japon, licence de données publiques 1.0) et MOLIT (Corée du Sud, car.go.kr).