Lecture libre · compte gratuit pour contribuerSuccesseur d’Anticars (2000)

Mercedes-BenzMercedes-Benz Classe E

1985– · 8 générations · 92 défauts documentés · 7 marchés
Générations

Tout sur la Mercedes-Benz Classe E, toutes générations confondues : défauts, rappels, notes techniques et discussions. Choisissez une génération pour affiner.

Défauts les plus graves

Tout voir (92) →
m
CritiqueÉlectroniqueNAClasse E W210 · 1994–2003

Electrical system: problems reported by owners

244 owners in the United States reported problems with the electrical system of this car to NHTSA (model years 1994–2001), typically at around 112,000 miles. Most often named: wiring:front underhood (24%), wiring (16%). Reported consequences: 3 crashes, 24 fires, 9 injuries.

✓ Analyse Mecafile de données officielles1994–2001Affiché en anglais d’origine · traduction en attenteVoir le détail →
m

Engine and cooling: problems reported by owners

91 owners in the United States reported problems with the engine and cooling of this car to NHTSA (model years 1994–2001), typically at around 77,000 miles. Most often named: engine (25%), engine:gasoline (16%). Reported consequences: 6 crashes, 5 fires, 11 injuries.

✓ Analyse Mecafile de données officielles1994–2001Affiché en anglais d’origine · traduction en attenteVoir le détail →
m
CritiqueHabitacleNAClasse E W210 · 1994–2003

Airbags: problems reported by owners

76 owners in the United States reported problems with the airbags of this car to NHTSA (model years 1995–2001), typically at around 120,000 miles. Most often named: frontal (26%). Reported consequences: 24 crashes, 4 fires, 29 injuries.

✓ Analyse Mecafile de données officielles1995–2001Affiché en anglais d’origine · traduction en attenteVoir le détail →
m

Transmission and drivetrain: problems reported by owners

54 owners in the United States reported problems with the transmission and drivetrain of this car to NHTSA (model years 1994–2001), typically at around 90,000 miles. Most often named: automatic transmission (43%). Reported consequences: 3 crashes, 2 fires, 2 injuries.

✓ Analyse Mecafile de données officielles1994–2001Affiché en anglais d’origine · traduction en attenteVoir le détail →

Derniers rappels officiels

Tout voir (713) →
Classe E V213 · 2016–2023
RappelModéréBoîteKR

동력전달장치 기타

공급업체의 생산 공정의 편차로 인해 시간이 지남에 따라 드라이브 샤프트의 유니버셜 조인트가 마모될 수 있으며, 이로 인해 유니버셜 조인트에서 윤활유 손실이 발생하여 유니버셜 조인트가 파손될 수 있음. 그 결과로 트랜스퍼 케이스와 전륜 구동 장치 간의 연결이 끊어져 추진력을 잃을 수 있고 충돌 위험이 증가할 수 있음이 확인됨에 따른 리콜 <대상차량별 생산일자> S 450 4MATIC: 2018.01.25~2019.11.14 S 560 4MATIC: 2019.08.30~2019.09.12 CLS 400 d 4MATIC: 2019.02.25~2019.04.11 S 350 d 4MATIC: 2019.04.09 E 450 4MATIC: 2019.02.05 S 400 d 4MATIC: 2017.12.11

MOLIT · Corée du Sud30 sept. 20266389Années modèle 2017–2019Affiché en coréen d’origine · traduction en attenteVoir le détail →
Classe E V213 · 2016–2023
RappelModéréBoîteUK

SRPC2603 - Drive Shaft Joint

Mercedes-Benz AG has determined that on certain 4MATIC E-Class (213 platform) S-Class Coupé (217 platform) S-Class (222 platform) E-Class Coupe/Convertible (238 platform) GLC (253 platform) and CLS (257 platform) vehicles increased wear of the universal joint on the drive shaft might occur.

DVSA · Royaume-Uni21 sept. 2026R/2026/148Années modèle 2019Affiché en anglais d’origine · traduction en attenteVoir le détail →
Classe E W212 · 2008–2016Classe E V213 · 2016–2023
RappelCritiqueSuspensionEU

Motorrijtuigen en aanhangwagens - stuurinrichting

De drie aluminium schroeven waarmee de power-pack aan de stuurinrichting is bevestigd, kunnen door blootstelling aan water en strooizout roesten.

rdw28 août 2026MGP230033Années modèle 2010–2016Affiché en néerlandais d’origine · traduction en attenteVoir le détail →

Derniers bulletins techniques

Tout voir (874) →
Classe E W214 · 2023–
BulletinMineurCarrosserieNA

Bulletin

Complaint Wheezing noises/squeaking noises from the front shock absorbers when passing over surface undulations and rough road. Noise MUST match those heard in the attached videos. Cause Wheezing noises: Flow noises of the damper oil Squeaking noises: From the mechanical rubber valve in the dividing piston Remedy In case of complaints, the front shock absorbers must be replaced. If shocks have been replaced and noise persists, please open a TIPS case to the Body, Chassis, Entertainment inbox.

NHTSA · bulletin constructeur11039086Années modèle 2024–2027Affiché en anglais d’origine · traduction en attenteVoir le détail →
Classe E W214 · 2023–
BulletinModéréSuspensionNA

Bulletin

Complaint Cracking noises on load change from rear axle (can be heard from wheel side). See attached reference video Cause Micromovement between the rear halfshaft (axle shaft) and wheel bearing mounting surface. Remedy To verify, a test drive and thorough NVH diagnosis must be performed in order to verify the root cause of the noise. If the axle shafts have been identified as the source of the noise, perform the following steps: 1. Verify that rear axle side shaft part number A 214 350 44 06 are currently installed on both sides. If an earlier part number is installed, replace the affected side shaft(s) with A 214 350 44 06. (Before installation, proceed with remaining steps) 2. Clean the contact surfaces of the side shafts and wheel bearings (remove any existing Molykote coating and wear debris). 3. Install one antiknock washer per side (A000 990 86 62) 4. Reinstall both side shafts 5. Perform road test and verify noise is no longer present Note: Application of Molykote coating is no longer required.

NHTSA · bulletin constructeur11038946Années modèle 2025–2027Affiché en anglais d’origine · traduction en attenteVoir le détail →
Classe E V213 · 2016–2023Classe E W214 · 2023–
BulletinModéréSuspensionNA

Bulletin

Complaint Diverse functional limitations in the vehicle in combination with various warning and fault messages in the instrument cluster display. Cause Communication timeouts mean that communication errors may occur in the onboard electrical system, which can result in various fault messages being displayed in the instrument cluster. This could be down to delayed feedback from the drivetrain control unit (N127) (CPC) to other control units networked to the CAN bus. Information: Only valid for vehicles through production period 10/2025. Not valid for vehicles with control unit CDCC (N125, central controller charging and driving) It may not be possible to attribute any communication errors stored in the control units on the CAN bus to a specific cause In rare instances, there may be a brief activation of the yellow warning lamp for engine diagnosis or there may be a sporadic delay with the start enable. There may not be any specific fault codes present that indicate a specific component. Example image: Fault messages in instrument cluster: The reason for this could be down to delayed feedback from the control unit CPC3 to other control units networked on the CAN bus. Remedy Do not replace any components!!! ******************************************************************************************************* 1. Connect charger (see AR54.10P1127WT). Note: An adequate voltage from the onboard electrical system battery must be guaranteed for the entire duration of the work procedure. Otherwise, the control units could be damaged if an undervoltage occurs. Information: Observe the operating instructions of the charger. Information: Use the charger to ensure an adequate voltage (at least 12.5 V) from the onboard electrical system battery. 2. Connect diagnostic system (see AD00.00P200006FR). Note: Always use the latest XENTRY Diagnostics software release. Information: Strict compliance with the operation steps in XENTRY Diagnostics is absolutely essential. 3. Select control unit N127 (CPC) via the direct link using XENTRY Diagnosis. Information: To do so, select the following menu items: Control units view Drive systems N127 "Drivetrain" control unit (CPC) 4. Update software for control unit N127 (CPC) (see AR54.21P001401Y). Info: To do so, select the following menu items: Adaptations Control unit update Update control unit software. Information: You are then automatically guided through the steps "Update of control unit software" and "SCN coding". Always observe the following operation steps at all times 5. Disconnect diagnostic device from vehicle (see AD00.00P200006FR). 6. Disconnect charger from vehicle (see AR54.10P1127WT).

NHTSA · bulletin constructeur11038925Années modèle 2023–2026Affiché en anglais d’origine · traduction en attenteVoir le détail →

Dernières discussions

Aucune discussion pour l’instant.

Les défauts et les discussions sont classés par génération : choisissez-en une ci-dessus pour ajouter le vôtre.

Sources : NHTSA (États-Unis, domaine public), Transports Canada (Licence du gouvernement ouvert – Canada), DVSA (Royaume-Uni, Open Government Licence v3.0), RappelConso et Safety Gate de l'UE (France, Licence Ouverte 2.0), MLIT (Japon, licence de données publiques 1.0) et MOLIT (Corée du Sud, car.go.kr).