Lecture libre · compte gratuit pour contribuerSuccesseur d’Anticars (2000)

Mercedes-BenzMercedes-Benz Classe GLE

1997– · 4 générations · 62 défauts documentés · 3 marchés
Générations

Tout sur la Mercedes-Benz Classe GLE, toutes générations confondues : défauts, rappels, notes techniques et discussions. Choisissez une génération pour affiner.

Défauts les plus graves

Tout voir (62) →
m

Transmission and drivetrain: problems reported by owners

64 owners in the United States reported problems with the transmission and drivetrain of this car to NHTSA (model years 1998–2004), typically at around 66,000 miles. Most often named: automatic transmission (59%). Reported consequences: 7 crashes, 5 injuries.

✓ Analyse Mecafile de données officielles1998–2004Affiché en anglais d’origine · traduction en attenteVoir le détail →

Derniers rappels officiels

Tout voir (455) →
Classe GLE GLE (W167/C167) · 2018–
Classe GLE GLE (W167/C167) · 2018–
RappelModéréAutreUK

Installation of the Heat Shield

Mercedes-Benz AG has determined that on certain GLE (167 platform) vehicles with OM654 and hybrid drive a heat shield in the firewall area might not be installed according to specification.

DVSA · Royaume-Uni14 sept. 2026R/2026/326Années modèle 2022–2025Affiché en anglais d’origine · traduction en attenteVoir le détail →
Classe GLE GLE (W167/C167) · 2018–
RappelCritiqueMoteurEU

In certain GLE series vehicles (model series 167) with OM654 and hybrid engines, a shielding plate in the…

In certain GLE series vehicles (model series 167) with OM654 and hybrid engines, a shielding plate in the bulkhead area may not have been fitted according to specifications. As a result, the fuel line could rub against the shielding plate and become damaged, causing a fuel leak. This may lead to a drop in fuel pressure and a loss of propulsion without warning, increasing the risk of an accident.

Safety Gate · UE3 sept. 2026SR/02418/26Années modèle 2022–2025Affiché en anglais d’origine · traduction en attenteVoir le détail →

Derniers bulletins techniques

Tout voir (858) →
Classe GLE GLE (W167/C167) · 2018–
BulletinModéréÉlectroniqueNA

Bulletin

Complaint Check engine light illuminated, or previously on One of the below Exhaust Flap fault codes stored in PTCU N127: P13C273 P13C278 P140473 Cause Various Remedy 1. Thaw exhaust system if ice is present. 2. Update software of N127 PTCU. 3. Check the exhaust flap for free movement. 4. Replace exhaust flap actuator. (P13C273 and P13C278 Right side flap, P140473 Left side flap). Ensure antirattle spring is installed in correct position. 5. Clear fault codes and check exhaust flap for free movement via actuation. If fault code reoccurs: Replace muffler with exhaust flap actuator. Note: For vehicles with two exhaust flap actuators, the left and right actuator have different part numbers. Installing two of the same side part number will cause fault codes due to missing LIN messages.

NHTSA · bulletin constructeur11039099Années modèle 2024–2025Affiché en anglais d’origine · traduction en attenteVoir le détail →
Classe GLE GLE (W167/C167) · 2018–
BulletinModéréÉlectroniqueNA

Bulletin

Complaint Customers may notice a check engine light in the instrument cluster and may also complain of rough running. One or more of the following DTCs may be stored in the ME control unit (N3/10): P227900 A leak was detected in the intake air system P152B00 A leak was detected in the intake air system (cylinder bank 1) P152C00 A leak was detected in the intake air system (cylinder bank 2) Cause Root cause varies Remedy Check the intake and the evaporative emissions system for leak tightness. Should you identify any leaks, repair them, clear the DTC(s) and test drive the vehicle. If the codes do not return, release the vehicle back to the customer. If the codes do return, then perform the tests located in the attached PDF titled "air leak work instructions". Then, open a TIPS case with the following information: Initial quick test ME control unit log Detailed results (including XENTRY print outs) of the tests performed in the "air leak work instructions"

NHTSA · bulletin constructeur11039096Années modèle 2026Affiché en anglais d’origine · traduction en attenteVoir le détail →
Classe GLE GLE (W167/C167) · 2018–
BulletinModéréSuspensionNA

Bulletin

Complaint Customer concern of Air Conditioning not cooling. *NOTE Use of tracer DYE for leak checks is not approved. Only approved leak check procedures as per WIS are approved. Cause Possible refrigerant leak. Remedy Perform the following measures : *Important* Photo documentation requirement is no longer in effect as of 10/1/2025. Remedy 1: Replace Evaporator (Only applies to vehicles produced PRIOR to April 15, 2022 and has NOT had the evaporator replaced previously) 1. Ensure that the rest of the AC system has been thoroughly checked for leaks with forming gas as per WIS before condemning the evaporator. 2. If no other leaks are found, replace the evaporator 3. *Important* when you get the new evaporator, check the expansion valve bracket to see if there are any bends (see attachment "Bent Bracket"). a. If bent, remove the expansion valve and bracket and check for damage to the flange (see attachment "Flange Damage"). i. If damage is found, order another evaporator and claim the part under parts warranty. The warranty claim MUST include a photo of the damage found. ii. If no damage is found, flip the bracket and torque to 7Nm. Check the evaporator for proper sealing before fully installing. b. If no bends are found, the evaporator should be installed in the vehicle. Note *If the evaporator housing has been opened or the evaporator or housing has been tampered with, the claim will be debited. Remedy 2: (Applies to all vehicles produced on or AFTER April 15, 2022 up to August 1, 2025) 1. Ensure that the entire AC system has been thoroughly checked for leaks with forming gas as per WIS . 2. If no leaks were found AND the system came in with no cooling/low charge, OR the evaporator is suspected of leaking: 3. Replace ONLY the expansion valve bracket, seals, and bolts as supplied in kit A 167 832 47 00, in accordance with the procedure outlined in WIS document AR83.30P5520ME. 4. IF THE PRODUCTION DATE IS BETWEEN JUNE 1, 2023 AND JULY 1, 2024, REPLACE THE DRYER AS WELL. (NOT THE CONDENSER) 5. After, charge the system and perform a few drive cycles. 6. Recheck the vehicle for leaks. 7. If no leaks are found, the vehicle can be released. 8. If a minor leak is detected that is less than 50ppm, then perform the following steps: If a leak is detected, fill the system with forming gas Close all doors and windows for 10 minutes. Vehicle off with no blower activation. Open the driver's door and measure ppm detection as soon as the door is open and the sniffer goes into the vehicle. If no leaks are measured, fill the system and release. If you still feel the evaporator is needed/leaks are still detected, a TIPS case is required for replacement. Provide all documentation listed in Remedy 3. Remedy 3: (Only applies to vehicles produced AFTER August 1, 2025) Ensure that the entire AC system has been thoroughly checked for leaks with forming gas as per WIS . If no leaks are found or the expansion valve has been found to be leaking, remove the expansion valve and check the bracket. If the bracket is bent, replace the expansion valve bracket, seals, and bolts as supplied in kit A 167 832 47 00. In the warranty submission, include photos of both sides of the bracket and a side profile so it can be seen that the bracket is bent. If the bracket is NOT bent or leaks from other locations are found, then open a TIPS case with the following: 1. Initial Quick Test 2. Create a short video of the actual pressures via AC machine, showing the engine running, and hold a copy of the VIN/RO in view as well. 3. OBS recording of XENTRY AC actual values of compressor request to be on and current value. (Instructions in Attachments) 4. Video recording of the leak being found via sniffer at the R/F AC drain after removing the under dash panel if the evaporator is suspected. (see attached videos) 5. If the evaporator is found to be leaking via sniffer, another video needs to be uploaded (or a continuation if only making the video after checks

NHTSA · bulletin constructeur11039062Années modèle 2023–2026Affiché en anglais d’origine · traduction en attenteVoir le détail →

Dernières discussions

Aucune discussion pour l’instant.

Les défauts et les discussions sont classés par génération : choisissez-en une ci-dessus pour ajouter le vôtre.

Sources : NHTSA (États-Unis, domaine public), Transports Canada (Licence du gouvernement ouvert – Canada), DVSA (Royaume-Uni, Open Government Licence v3.0), RappelConso et Safety Gate de l'UE (France, Licence Ouverte 2.0), MLIT (Japon, licence de données publiques 1.0) et MOLIT (Corée du Sud, car.go.kr).