Tout sur la Mercedes-Benz Classe S, toutes générations confondues : défauts, rappels, notes techniques et discussions. Choisissez une génération pour affiner.
273 owners in the United States reported problems with the electrical system of this car to NHTSA (model years 1999–2005), typically at around 93,000 miles. Most often named: instrument cluster/panel (30%). Reported consequences: 1 crash, 11 fires, 3 injuries.
✓ Analyse Mecafile de données officielles1999–2005Affiché en anglais d’origine · traduction en attenteVoir le détail →
44 owners in the United States reported problems with the engine and cooling of this car to NHTSA (model years 2000–2005), typically at around 57,000 miles. Most often named: engine (32%). Reported consequences: 2 fires, 1 injury.
✓ Analyse Mecafile de données officielles2000–2005Affiché en anglais d’origine · traduction en attenteVoir le détail →
30 owners in the United States reported problems with the airbags of this car to NHTSA (model years 1999–2005), typically at around 90,000 miles. Most often named: frontal (17%). Reported consequences: 6 crashes, 1 fire, 10 injuries.
✓ Analyse Mecafile de données officielles1999–2005Affiché en anglais d’origine · traduction en attenteVoir le détail →
25 owners in the United States reported problems with the accelerator and cruise control of this car to NHTSA (model years 2000–2005), typically at around 70,000 miles. Reported consequences: 4 crashes.
✓ Analyse Mecafile de données officielles2000–2005Affiché en anglais d’origine · traduction en attenteVoir le détail →
68 owners in the United States reported problems with the electrical system of this car to NHTSA (model years 1993–1997), typically at around 130,000 miles. Most often named: wiring:front underhood (21%). Reported consequences: 6 fires.
✓ Analyse Mecafile de données officielles1993–1997Affiché en anglais d’origine · traduction en attenteVoir le détail →
Les tuyaux de frein de l'essieu avant peuvent présenter une fuite, ce qui provoque l'échappement du liquide de frein. cela pourrait réduire les performances de freinage et, si le fluide se déverse sur la route, réduire l'adhérence des véhicules suivants, augmentant ainsi le risque d'accident.
Complaint Customer states check engine light ON and potentially reduced power output. The following DTC's may be current and/or stored in the ME control unit (N3/10): P210185 The throttle valve actuator has a malfunction. There is a signal above the permissible limit value. P213500 The values from the position sensors of the throttle valve are implausible relative to each other P213600 The values from position sensors "A/C" of the throttle valve are implausible relative to each other P210B85 The throttle valve actuator 2 has a malfunction. There is a signal above the permissible limit value. P2AD300 The values from the position sensors "A/G" of the throttle valve are implausible relative to each other P2AD200 The values from position sensors "B/G" of the throttle valve are implausible relative to each other. NOTE: The faults may also be present in the ME control unit "faults without status filter" Cause Increased electrical resistance between the pins for left and right throttle actuators (M16/60 and M16/61) and the sockets on the engine wiring harness connector. Remedy Replace the sockets in the engine wiring harness connector at both the left and right throttle actuator with the following parts: Silver Plated Sockets 8x A 003 982 70 26 (according to wiring diagram 0.5 mm) 4x A 003 982 73 26 (according to wiring diagram 0.75 mm) ELA Seals 12x A 001 545 50 80
NHTSA · bulletin constructeur11039063Années modèle 2021Affiché en anglais d’origine · traduction en attenteVoir le détail →
Complaint Diverse functional limitations in the vehicle in combination with various warning and fault messages in the instrument cluster display. Cause Communication timeouts mean that communication errors may occur in the onboard electrical system, which can result in various fault messages being displayed in the instrument cluster. This could be down to delayed feedback from the drivetrain control unit (N127) (CPC) to other control units networked to the CAN bus. Information: Only valid for vehicles through production period 10/2025. Not valid for vehicles with control unit CDCC (N125, central controller charging and driving) It may not be possible to attribute any communication errors stored in the control units on the CAN bus to a specific cause In rare instances, there may be a brief activation of the yellow warning lamp for engine diagnosis or there may be a sporadic delay with the start enable. There may not be any specific fault codes present that indicate a specific component. Example image: Fault messages in instrument cluster: The reason for this could be down to delayed feedback from the control unit CPC3 to other control units networked on the CAN bus. Remedy Do not replace any components!!! ******************************************************************************************************* 1. Connect charger (see AR54.10P1127WT). Note: An adequate voltage from the onboard electrical system battery must be guaranteed for the entire duration of the work procedure. Otherwise, the control units could be damaged if an undervoltage occurs. Information: Observe the operating instructions of the charger. Information: Use the charger to ensure an adequate voltage (at least 12.5 V) from the onboard electrical system battery. 2. Connect diagnostic system (see AD00.00P200006FR). Note: Always use the latest XENTRY Diagnostics software release. Information: Strict compliance with the operation steps in XENTRY Diagnostics is absolutely essential. 3. Select control unit N127 (CPC) via the direct link using XENTRY Diagnosis. Information: To do so, select the following menu items: Control units view Drive systems N127 "Drivetrain" control unit (CPC) 4. Update software for control unit N127 (CPC) (see AR54.21P001401Y). Info: To do so, select the following menu items: Adaptations Control unit update Update control unit software. Information: You are then automatically guided through the steps "Update of control unit software" and "SCN coding". Always observe the following operation steps at all times 5. Disconnect diagnostic device from vehicle (see AD00.00P200006FR). 6. Disconnect charger from vehicle (see AR54.10P1127WT).
NHTSA · bulletin constructeur11038925Années modèle 2021–2023Affiché en anglais d’origine · traduction en attenteVoir le détail →
Issue On the subject vehicles, the transmission control unit (VGS) in the automatic transmission does not conform to current production specifications. It is possible that the polarities of the magnets in the transmission control unit (VGS) could have been incorrectly installed, leading to potential shift quality issues and gear lockouts. Remedy MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will update the software of the electric controller unit "fully integrated transmission control" in the affected vehicles.
NHTSA · bulletin constructeur11038924Années modèle 2026Affiché en anglais d’origine · traduction en attenteVoir le détail →
Dernières discussions
Aucune discussion pour l’instant.
Les défauts et les discussions sont classés par génération : choisissez-en une ci-dessus pour ajouter le vôtre.
Sources : NHTSA (États-Unis, domaine public), Transports Canada (Licence du gouvernement ouvert – Canada), DVSA (Royaume-Uni, Open Government Licence v3.0), RappelConso et Safety Gate de l'UE (France, Licence Ouverte 2.0), MLIT (Japon, licence de données publiques 1.0) et MOLIT (Corée du Sud, car.go.kr).