Lecture libre · compte gratuit pour contribuerSuccesseur d’Anticars (2000)

SaabSaab 9-3

1998–2014 · 3 générations · 35 défauts documentés · 2 marchés
Générations

Les bulletins techniques (TSB) sont des instructions de réparation que les constructeurs envoient à leurs concessionnaires sur des problèmes connus. Ce ne sont pas des rappels de sécurité, mais ils confirment souvent un défaut.

Année modèle
MarchéTousEUNAUK
9-3 I · 2002–2012
BulletinModéréÉlectroniqueNA

Bulletin

Cette communication d'information préliminaire fournit au technicien des informations sur les véhicules présentant un problème intermittent de non-démarrage, de démarrage impossible ou de calage au démarrage, avec le voyant de sécurité qui s'allume. Le technicien peut trouver les codes de défaut de diagnostic B3055, B3060 et/ou B3935. Le technicien ne doit remplacer aucune pièce pour ce problème. Si le problème ne peut pas être reproduit, demander au client s'il utilise des dispositifs d'identification par radiofréquence (RFID) lorsque le problème se manifeste. Le concessionnaire doit également orienter ses clients vers la section appropriée des manuels du propriétaire qui indique que le dispositif est conforme.

NHTSA · bulletin constructeur10201176Années modèle 2009Traduit automatiquement · original : anglaisVoir le détail →
9-3 I · 2002–2012
BulletinModéréÉlectroniqueNA

Bulletin

This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies. Wait, I need to correct myself: the text above is still in English. Here is the French translation: Cette communication d'information préliminaire fournit au technicien des informations sur les véhicules présentant un problème intermittent de non-démarrage, de non-démarrage sans rotation du moteur ou de calage au démarrage, avec le voyant de sécurité qui s'allume. Le technicien peut trouver les codes de diagnostic de panne B3055, B3060 et/ou B3935. Le technicien ne doit remplacer aucune pièce pour ce problème. Si le problème ne peut pas être reproduit, demander au client s'il utilise des dispositifs d'identification par radiofréquence lorsque le problème se manifeste. Le concessionnaire doit également orienter ses clients vers la section appropriée des manuels du propriétaire qui indique que le dispositif est conforme.

NHTSA · bulletin constructeur10178384Années modèle 2009Traduit automatiquement · original : anglaisVoir le détail →
9-3 I · 2002–2012
BulletinModéréÉlectroniqueNA

Bulletin

Cette communication d'information préliminaire fournit au technicien des informations sur les véhicules présentant un problème intermittent de non-démarrage, de démarrage impossible ou de calage au démarrage, avec le voyant de sécurité qui s'allume. Le technicien peut constater les codes de diagnostic de panne B3055, B3060 et/ou B3935. Le technicien ne doit remplacer aucune pièce pour ce problème. Si le problème ne peut pas être reproduit, demandez au client s'il utilise des dispositifs d'identification par radiofréquence (RFID) lorsque le problème se manifeste. Le concessionnaire doit également orienter ses clients vers la section appropriée des manuels du propriétaire qui indique que l'appareil est conforme.

NHTSA · bulletin constructeur10174861Années modèle 2009Traduit automatiquement · original : anglaisVoir le détail →
9-3 I · 2002–2012
BulletinModéréÉlectroniqueNA

Bulletin

No Crank/No Start, Dead Battery Due to Parasitic Drain/Discharge.

NHTSA · bulletin constructeur10254206Années modèle 2011Affiché en anglais d’origine · traduction en attenteVoir le détail →
9-3 I · 2002–2012
BulletinModéréÉlectroniqueNA

Bulletin

No Crank/No Start, Dead Battery Due to Parasitic Drain/Discharge.

NHTSA · bulletin constructeur10254207Années modèle 2011Affiché en anglais d’origine · traduction en attenteVoir le détail →
9-3 I · 2002–2012
BulletinModéréÉlectroniqueNA

Bulletin

This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.

NHTSA · bulletin constructeur10114954Années modèle 2009Affiché en anglais d’origine · traduction en attenteVoir le détail →
9-3 I · 2002–2012
BulletinModéréÉlectroniqueNA

Bulletin

This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon an upper engine and valve cleaning should be performed.

NHTSA · bulletin constructeur10114746Années modèle 2009Affiché en anglais d’origine · traduction en attenteVoir le détail →
9-3 I · 2002–2012
BulletinModéréÉlectroniqueNA

Bulletin

This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon, an upper engine and valve cleaning should be performed. Update added part numbers for the cleaner and model years.

NHTSA · bulletin constructeur10113418Années modèle 2009Affiché en anglais d’origine · traduction en attenteVoir le détail →
9-3 I · 2002–2012
BulletinModéréÉlectroniqueNA

Bulletin

This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.

NHTSA · bulletin constructeur10111927Années modèle 2009Affiché en anglais d’origine · traduction en attenteVoir le détail →
9-3 I · 2002–2012
BulletinModéréÉlectroniqueNA

Bulletin

This preliminary information communication provides information to the technician about vehicles that have a malfunction indicator lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published service information diagnostics. If technician finds carbon, an upper engine and valve cleaning should be performed.

NHTSA · bulletin constructeur10099252Années modèle 2009Affiché en anglais d’origine · traduction en attenteVoir le détail →
9-3 I · 2002–2012
BulletinMineurÉlectroniqueNA

Bulletin

This warranty administration bulletin provides policy information on the requirements for 12V battery testing and warranty replacements.

NHTSA · bulletin constructeur10253527Années modèle 2010Affiché en anglais d’origine · traduction en attenteVoir le détail →
9-3 I · 2002–2012
BulletinMineurÉlectroniqueNA

Bulletin

This warranty administration bulletin provides policy information on the requirements for 12V battery testing and warranty replacements.

NHTSA · bulletin constructeur10252774Années modèle 2010Affiché en anglais d’origine · traduction en attenteVoir le détail →
9-3 I · 2002–2012
BulletinMineurÉlectroniqueNA

Bulletin

This service bulletin provides information for dealers/technicians on OnStar Module 2G Sunset Information.

NHTSA · bulletin constructeur10230605Années modèle 2010Affiché en anglais d’origine · traduction en attenteVoir le détail →
9-3 I · 2002–2012
BulletinMineurÉlectroniqueNA

Bulletin

This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.

NHTSA · bulletin constructeur10165123Années modèle 2009Affiché en anglais d’origine · traduction en attenteVoir le détail →
9-3 I · 2002–2012
BulletinMineurÉlectroniqueNA

Bulletin

This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will use Global Diagnostic System 2 to review the Firmware Over-the-Air version. If the Firmware Over-the-Air version on the scan tool equals 6708 the technician will need to contact General Motors Technical Assistance Center for further assistance. If the Firmware Over-the-Air version on the scan tool is lower than 6708 Dealer can order the part thought the Instrument Sales and Service website process.

NHTSA · bulletin constructeur10157041Années modèle 2009Affiché en anglais d’origine · traduction en attenteVoir le détail →
9-3 I · 2002–2012
BulletinMineurÉlectroniqueNA

Bulletin

This informational bulletin provides information to diagnose batteries that have set for a long period of time and/or cold weather climates and testing those batteries.

NHTSA · bulletin constructeur10139282Années modèle 2009Affiché en anglais d’origine · traduction en attenteVoir le détail →
9-3 I · 2002–2012
BulletinMineurÉlectroniqueNA

Bulletin

This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.

NHTSA · bulletin constructeur10139179Années modèle 2009Affiché en anglais d’origine · traduction en attenteVoir le détail →
9-3 I · 2002–2012
BulletinMineurÉlectroniqueNA

Bulletin

This informational bulletin provides information to diagnose batteries that have set for a long period of time and/or cold weather climates and testing those batteries.

NHTSA · bulletin constructeur10139185Années modèle 2009Affiché en anglais d’origine · traduction en attenteVoir le détail →
9-3 I · 2002–2012
BulletinMineurÉlectroniqueNA

Bulletin

This technical bulletin provides a procedure to clear the codes and re-evaluate the XM radio channels to correct a condition of audio muting when listening to some Sirius XM channels but if they change channels they will find others that experience normal audio. This could be due to interference from transmitting sources outside of Sirius XM?s frequency range.

NHTSA · bulletin constructeur10139099Années modèle 2009Affiché en anglais d’origine · traduction en attenteVoir le détail →
9-3 I · 2002–2012
BulletinMineurÉlectroniqueNA

Bulletin

This informational bulletin provides information on On rare occasions, a security code input message with SPS error code E5659, M5304, and/or M5530 may be displayed in TIS2web when the technician is programming any module. If this concern is encountered, the technician should start by ensuring that the module being programmed is not a used module and that the VIN matches on VIN plate, TIS2web programming screen, and GDS2 module identification information screen.

NHTSA · bulletin constructeur10138054Années modèle 2009Affiché en anglais d’origine · traduction en attenteVoir le détail →
9-3 I · 2002–2012
BulletinMineurÉlectroniqueNA

Bulletin

This technical bulletin provides a procedure to properly reprogram an onstar module to correct a condition of Red LED, No WiFi Operation, and/or Limited OnStar Module Functionality After OnStar Module Replacement for Another Condition.

NHTSA · bulletin constructeur10137375Années modèle 2009Affiché en anglais d’origine · traduction en attenteVoir le détail →
9-3 I · 2002–2012
BulletinMineurÉlectroniqueNA

Bulletin

This informational bulletin provides information on communication with OnStar module after Canadian cellular upgrade.

NHTSA · bulletin constructeur10135369Années modèle 2009Affiché en anglais d’origine · traduction en attenteVoir le détail →
9-3 I · 2002–2012
BulletinMineurÉlectroniqueNA

Bulletin

This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.

NHTSA · bulletin constructeur10135322Années modèle 2009Affiché en anglais d’origine · traduction en attenteVoir le détail →
9-3 I · 2002–2012
BulletinMineurÉlectroniqueNA

Bulletin

This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.

NHTSA · bulletin constructeur10135342Années modèle 2009Affiché en anglais d’origine · traduction en attenteVoir le détail →
9-3 I · 2002–2012
BulletinMineurÉlectroniqueNA

Bulletin

This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.

NHTSA · bulletin constructeur10135242Années modèle 2009Affiché en anglais d’origine · traduction en attenteVoir le détail →
Plus anciens →

Sources : NHTSA (États-Unis, domaine public), Transports Canada (Licence du gouvernement ouvert – Canada), DVSA (Royaume-Uni, Open Government Licence v3.0), RappelConso et Safety Gate de l'UE (France, Licence Ouverte 2.0), MLIT (Japon, licence de données publiques 1.0) et MOLIT (Corée du Sud, car.go.kr).