Lettura libera · account gratuito per contribuireErede di Anticars (2000)

BMW Serie 3 E30

1982–1994 · 15 difetti documentati · 4 mercati
Anno modello
MercatoTuttiNAUK
RichiamoCriticoMotoreNA

Sistema di alimentazione

Su alcuni veicoli 318I, 318IC, 318IS, 325IC, 325IS, 325IX, 525I, 535I, 735I e 735IL, il tubo di alimentazione del carburante può indurirsi e "deformarsi" nel tempo a causa delle temperature del vano motore. Se si verifica questa "deformazione", è possibile che si verifichino trafilamenti tra il tubo e il raccordo, poiché la fascetta potrebbe non esercitare una forza di tenuta sufficiente a compensare l'indurimento del tubo. La fuoriuscita di carburante, in presenza di una fonte di accensione, potrebbe causare un incendio nel vano motore. Correzione: i tubi di alimentazione del carburante e le relative fascette saranno sostituiti con componenti di un nuovo modello.

Transport Canada30 mag 19941994096Anni modello 1989Tradotto automaticamente · originale: ingleseVedi dettagli →
RichiamoCriticoMotoreNA

Sistema di alimentazione, benzina: Erogazione: Tubi flessibili, tubazioni e raccordi

Con il tempo, i tubi di alimentazione del carburante possono indurirsi e "fissarsi" in posizione, causando una perdita di carburante nel punto di collegamento tra il tubo e il raccordo del motore. La fascetta utilizzata per fissare il tubo al raccordo non è in grado di compensare l'indurimento del tubo di alimentazione del carburante.

NHTSA · Stati Uniti11 apr 199494V066000Anni modello 1989Tradotto automaticamente · originale: ingleseVedi dettagli →
RichiamoCriticoElettronicaNA

Heater And Defroster

On certain 318I vehicles, under certain conditions, the interior heater water control valve may bind while closing. This binding or slow-closing condition may cause the valve solenoid to draw excessive current, possibly resulting in overheating of the valve connector wiring and insulation. This condition could result in a passenger compartment fire.

Transport Canada24 set 19841984105Anni modello 1984Mostrato in inglese originale · traduzione in attesaVedi dettagli →
RichiamoModeratoMotoreNA

Heater And Defroster

On certain 318I, 325I and M3 vehicles, elevated pressure in the cooling system due to overheating could result in cracking of the heater core end piece. Should this happen, coolant could be expelled onto the lower right leg of the driver, possibly resulting in personal injury and/or fogging of the interior surfaces of the windows causing reduced driver vision. Correction: A thermistatic bypass valve will be installed to control coolant temperature in the heater core. Also, a new design radiator cap will be installed to control pressure and provide greater overflow.

Transport Canada19 lug 19931993100Anni modello 1984–1989Mostrato in inglese originale · traduzione in attesaVedi dettagli →
RichiamoModeratoMotoreNA

Engine

On certain 325IX vehicles, the oil dipstick tube attaching bracket may have been bent during the manufacturing process or during scheduled maintenance. This could possibly cause the dipstick to interfere with the throttle bellcrank lever's range of motion and prevent the lever from returning to the idle position after release of the accelerator pedal. Correction: Throttle bellcrank lever will be modified to provide sufficient clearance. Note: Vehicles with manual transmission only.

Transport Canada6 apr 19881988049Anni modello 1988Mostrato in inglese originale · traduzione in attesaVedi dettagli →
RichiamoModeratoMotoreNA

Vehicle speed control:Cables

The oil dipstick tube attaching bracket may have been bent during production or scheduled maintenance, reducing the clearance between the dipstick ring and the throttle bellcrank lever.

NHTSA · Stati Uniti15 mar 198888V031000Anni modello 1988Mostrato in inglese originale · traduzione in attesaVedi dettagli →
RichiamoModeratoElettronicaNA

Electrical

On certain 325E, 325ES, 528E, 535I, 635CSI and 735I vehicles, the center high mounted brake light could add sufficient electrical load to cause the brake light switch to overheat, eventually leading to melting of the plastic internal switch parts. This could cause the switch plunger to jam in the ON or OFF position. This would render the brake light permanently ON or OFF regardless of brake pedal operation. Correction: A brake light switch with an increased current load capacity will be installed on affected vehicles.

Transport Canada27 nov 19861986134Anni modello 1986–1987Mostrato in inglese originale · traduzione in attesaVedi dettagli →
RichiamoModeratoFreniNA

Exterior lighting:Brake lights:Switch

Brake light switch could overheat, eventually leading to melting of plastic internal parts in area of electrical contacts.

NHTSA · Stati Uniti10 nov 198686V151000Anni modello 1986–1987Mostrato in inglese originale · traduzione in attesaVedi dettagli →
RichiamoModeratoSospensioniNA

Steering

On certain 318I, 325, 325E and 325ES vehicles, when a significant force is applied directly to the steering gearbox as the result of certain frontal crash conditions or front end contact with an object on the road, the steering column disengagement element, which is designed to reduce the amount of steering wheel rearward travel, could disengage completely. This would result in loss of post impact steering maneuverability without prior warning. Correction: Two plates will be bolted to the disengagement element to ensure that the element will not completely disengage in the event of an impact to the steering gear.

Transport Canada22 ott 19861986117Anni modello 1984–1986Mostrato in inglese originale · traduzione in attesaVedi dettagli →
RichiamoModeratoSospensioniNA

Steering: Steering wheel/handle bar

The two parts of the steering column disengagement element could completely disconnect if the car contacts an object in the roadway or elsewhere of sufficient mass to apply a significant force directly to the steering gearbox. Consequence of defect: Steering control would be lost.

NHTSA · Stati Uniti20 ott 198686V138000Anni modello 1985–1986Mostrato in inglese originale · traduzione in attesaVedi dettagli →
RichiamoModeratoMotoreNA

Fuel system, gasoline:Carburetor system

The idle control valve which controls idle speed by varying the amount of intake air that bypasses the throttle plate is subject to backfire into the intake manifold. Such backfire can damage the valve and cause the idle valve plate to remain open. Consequence of defect: This will result in abnormally high idle speed.

NHTSA · Stati Uniti6 mag 198585V058000Anni modello 1984Mostrato in inglese originale · traduzione in attesaVedi dettagli →
RichiamoModeratoMotoreNA

Engine

On certain 320I vehicles, crack in the exhaust system between the exhaust pipe and the catalytic converter could result in exhaust emissions which do not comply with CMVSS 1103.

Transport Canada22 dic 19831983121Anni modello 1981–1982Mostrato in inglese originale · traduzione in attesaVedi dettagli →
RichiamoLieveMotoreNA

Engine

On certain 318I vehicles, improper starting procedure could cause a backfire into the intake manifold and damage internal components of the idle control valve. This could result in abnormally high idle speed and if warnings of increased engine noise level and tachometer reading are not heeded, a vehicle crash could occur.

Transport Canada6 giu 19851985072Anni modello 1984Mostrato in inglese originale · traduzione in attesaVedi dettagli →

Fonti: NHTSA (Stati Uniti, pubblico dominio), Transport Canada (Open Government Licence – Canada), DVSA (Regno Unito, Open Government Licence v3.0), RappelConso e Safety Gate UE (Francia, Licence Ouverte 2.0), MLIT (Giappone, Public Data License 1.0) e MOLIT (Corea del Sud, car.go.kr).