Lettura libera · account gratuito per contribuireErede di Anticars (2000)

BMW Serie 3 (E46)

1997–2006 · 23 difetti documentati · 1 mercati

I bollettini tecnici (TSB) sono istruzioni di riparazione che i costruttori inviano ai concessionari su problemi noti. Non sono richiami di sicurezza, ma spesso confermano un difetto.

Anno modello
MercatoTuttiNA
BollettinoCriticoElettronicaNA

Bollettino

"? NO REGENERATION OF THE DIESEL PARTICULATE FILTER (DPF) This Service Information bulletin supersedes SI B18 03 10 dated November 2010. . The Service Engine Soon lamp is illuminated. The following fault codes may be stored in the DDE: N47T/N57T engine 245700 - Particle filter system: particulate filter highly loaded (Exhaust backpressure high) 245800 - particle filter system - filter is heavily contaminated. (exhaust backpressure is above maximum) M57Y engine 480A Particle filter system - filter is heavily contaminated. (exhaust backpressure is too high) 481A Particle filter system - filter is heavily contaminated. (exhaust backpressure is above maximum) CAUSE 1. Faults with the exhaust system that affect the monitoring of the DPF by the DDE 2. Unfavorable recent driving profile INFORMATIOM During normal driving, there is a continuous regeneration of the diesel particulate filter that takes place at exhaust-gas temperatures between 280 and 350C (slower oxidation process). The soot particles can only be burned off when the required exhaust-gas temperature has been reached. Under certain driving conditions (i.e., prolonged short trips or an exhaust system which never reaches soot burn-off temperatures), the DPF can become restricted. The DDE will initiate periodic regeneration automatically, at the latest after 600 miles. In vehicles making many short distance journeys, periodic regeneration takes place after only 250-500 miles. The Digital Diesel Electronics control unit evaluates the time for periodic regeneration from the following values: average distance driven average driving speed temperature in the diesel particulate filter values from the exhaust pressure sensor The DDE initiates the regeneration process by decreasing incoming air by the throttle valve, and one or two post injections are executed. This heats the exhaust-gas temperature to approx. 600 C . When the exhaust temp reaches this point: The soot is burned off with the residual oxygen. The

NHTSA · bollettino del costruttore10146535Anni modello 2006Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoModeratoElettronicaNA

Bollettino

N55 Engine: Various Faults Stored in DME Related to VANOS and Camshaft Position. A rattling noise can be heard from the engine compartment; the engine has a loss of power; and the Service Engine Soon lamp is illuminated. One or more of the following faults may be stored. E70, E71, E82, E88, E90, E92 and E93: 2D5A - VANOS, intake: control fault, camshaft sticking 2D5B - VANOS, intake: control fault, position not reached 2D60 - VANOS, exhaust: control fault, camshaft sticking 2D61 - VANOS, exhaust: control fault, position not reached 2D9F - camshaft input sensor: signal implausible 2DA1 - Camshaft exhaust sensor: signal implausible 300C - Camshaft input sensor: signal high 300D - Camshaft input sensor: signal low 300E - Camshaft exhaust sensor: signal high 300F - Camshaft exhaust sensor: signal low F07, F10, F12, F13 and F25: 130104 - VANOS, intake: control fault, camshaft sticking 130108 - VANOS, intake: control fault, position not reached 130304 - VANOS, exhaust: control fault, camshaft sticking 130308 - VANOS, exhaust: control fault, position not reached 130E11 - Camshaft input sensor: signal implausible 130F11 - Camshaft exhaust sensor: signal implausible 164020 - Camshaft input sensor: signal high 164021 - Camshaft input sensor: signal low 164030 - Camshaft exhaust sensor: signal high 164031 - Camshaft exhaust sensor: signal low CAUSE One or both (intake and/or exhaust) of the VANOS gear assemblies have failed; the attaching bolts may have also loosened and/or broken.

NHTSA · bollettino del costruttore10162395Anni modello 2006Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoModeratoElettronicaNA

Bollettino

N51, N52, N52K and N52T Engines: Various Eccentric Shaft Sensor Faults stored in the DME - Diagnostic Hints This Service Information bulletin and attachment supersedes SI B11 06 16 dated April 2016.. The customer may complain about one of the following: Rough engine running Engine cannot be started (crank no start) Check Engine Light illuminated One or more of the following faults may be stored in the DME: 2A37 - Valvetronic, eccentric shaft sensor plausibility 2A47 - Valvetronic, eccentric shaft, signal plausibility 134E08 - Eccentric shaft plausibility (on F10, F25 vehicles only) CAUSE The VVT eccentric shaft sensor connector, and/or DME connector may have oil contamination due to oil leakage at the VVT sensor gasket.

NHTSA · bollettino del costruttore10151300Anni modello 2006Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoModeratoElettronicaNA

Bollettino

N51, N52, N52K and N52T Engines: Various Eccentric Shaft Sensor Faults stored in the DME - Diagnostic Hints. The customer may complain about one of the following: Rough engine running Engine cannot be started (crank no start) Check Engine Light illuminated One or more of the following faults may be stored in the DME: 2A37 - Valvetronic, eccentric shaft sensor plausibility 2A47 - Valvetronic, eccentric shaft, signal plausibility 134E08 - Eccentric shaft plausibility (on F10, F25 vehicles only) CAUSE The VVT eccentric shaft sensor connector, and/or DME connector may have oil contamination due to oil leakage at the VVT sensor gasket.

NHTSA · bollettino del costruttore10151247Anni modello 2006Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoModeratoElettronicaNA

Bollettino

N51 Engine: Service Engine Soon Lamp Illuminated - Loss of Power and Various Faults Stored in the DME. The customer complains that the Service Engine Soon lamp is illuminated. The vehicle has lost power; the engine cranks but will not start; and various faults are stored in the DME for engine misfire and/or mixture adaptations. CAUSE The vehicle has lost fuel system delivery pressure due to a loose or split fuel line inside the fuel tank. The failure is related to an unfavorable stacking of tolerances between the rubber fuel hose and the plastic regulator nipple or deterioration of the rubber hose construction material.

NHTSA · bollettino del costruttore10151170Anni modello 2006Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoModeratoElettronicaNA

Bollettino

"N54 Engine: Diagnosis of Cold Start Rough Running with Misfire Faults. The customer may complain that during the cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. Various misfire fault codes (e.g., 29CC, 29D2, 29D1, 29D0, 29C0, 29CF) may be stored in the DME control module. The engine rough running complaint can be reproduced on a cold start in the workshop. During the course of diagnosis, the spark plugs, removed from the misfiring cylinders after the problem was reproduced, are found to be soaked (""wet"") with fuel, while the injector tips are covered with a layer of carbon deposit. Possible cause: high-pressure injector failure (leakage or incorrect spraying pattern) due to internal wear or unfavorable stock of tolerances IMPORTANT: For comprehensive N54 drivability diagnostics, always refer to the ""N54 Engine Diagnostic Fault Tree"" file (the current version ""02_14_13"" is found as a PDF attachment to SI B12 55 06)."

NHTSA · bollettino del costruttore10149589Anni modello 2006Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoModeratoElettronicaNA

Bollettino

N51 Engine: Service Engine Soon Lamp Illuminated - Loss of Power and Various Faults Stored in the DME. The customer complains that the Service Engine Soon lamp is illuminated. The vehicle has lost power; the engine cranks but will not start; and various faults are stored in the DME for engine misfire and/or mixture adaptations. CAUSE The vehicle has lost fuel system delivery pressure due to a loose or split fuel line inside the fuel tank. The failure is related to an unfavorable stacking of tolerances between the rubber fuel hose and the plastic regulator nipple or deterioration of the rubber hose construction material.

NHTSA · bollettino del costruttore10149349Anni modello 2006Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoModeratoElettronicaNA

Bollettino

RAD2+ Radio: Background Noise with Audio Turned Off. Background noise (buzzing, crackling, static) can be heard: * At low audio volume * When the radio is turned off * When the ignition is turned off NOTE: Background noise stops when the radio enters sleep mode. IMPORTANT: Background noise is more noticeable on vehicles produced before 09/2009 in case a RAD2+ replacement radio was installed previously. RAD2+ radio concept, manufactured from July 2009 to February 2014

NHTSA · bollettino del costruttore10148008Anni modello 2006Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoModeratoElettronicaNA

Bollettino

This Service Information bulletin supersedes SI B65 05 09 dated July 2009. designates changes to this revision SUBJECT CIC Headunit: Navigation System Road Map Usage. INFORMATION The Car Information Computer (CIC) began replacing the Car Communication Computer (CCC) on vehicles with option 609 in September of 2008. This change affected the navigation system road map data support process and the warranty spare parts processes for the CIC. For the US market, all vehicles come pre-loaded from the factory with the latest navigation system road map database version that was available at the time of vehicle production. Therefore, no physical copy of the navigation system road map data media DVD set or USB stick is placed in these vehicles at the Vehicle Distribution Center (VDC). NOTE: Additionally, all replacement CIC parts come with a pre-loaded version of the current available navigation system road map database installed. A set of DVD copies of the navigation system road map database, CIC NAVI Road Map North America PREMIUM, is shipped to all BMW centers through the automatic tool shipment program with each release of a navigation system road map database. IMPORTANT: Additional copies or earlier NAV road map database versions cannot be ordered individually! Therefore, please take special care to archive the CIC NAV road map DVD sets! The NAV road map data on the DVD set can also be installed into the Network Attached Storage (NAS). From there, it can then be installed onto the CIC in the vehicle, using the Integrated Service Technical Application for Programming (ISTA/P). For installation of the navigation system road map data media DVD set onto the Network Attached Storage (NAS), please contact your ISPI Next Administrator. In addition to this procedure, it is also possible to download the NAV road map data on the DVD set directly to the hard disc drive (HDD) integrated in the CIC by inserting the DVDs one by one into the CIC internal DVD drive. It will take approxim

NHTSA · bollettino del costruttore10147623Anni modello 2006Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoModeratoElettronicaNA

Bollettino

Bmw vehicles: Engine cranks but does not start; fuel level gauge displays a sufficient amount of fuel, although the fuel tank is empty; fault code 2a1c (fuel level plausibility) is stored in msv80. Right side fuel sending unit is dislodged from its bracket due to incorrect assembly. No model years listed. *pe updated 4/29/11. *pe

NHTSA · bollettino del costruttore10033131Anni modello 2003Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoModeratoElettronicaNA

Bollettino

Bmw: Various electrical problems or intermittently. Symptoms typically include various warning lamps in the instrument cluster and starting problems. Affected may be the ekp (electronically controlled fuel pump), and control modules on the pt can or connected to the 15wup (wake up) line. Fuse f70 may be blown. No model years listed. E93 (3 series convertible). *pe

NHTSA · bollettino del costruttore10031584Anni modello 2003Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoModeratoElettronicaNA

Bollettino

Installation instructions on fog lights for 318ti vehicles. *yc

NHTSA · bollettino del costruttore601931Anni modello 1998Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoLieveElettronicaNA

Bollettino

Starter Return

NHTSA · bollettino del costruttore11033106Anni modello 2002Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoLieveElettronicaNA

Bollettino

The electrical system of BMW vehicles has been subject to an ongoing development process over the last few years. This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle discharged battery complaints.

NHTSA · bollettino del costruttore10249027Anni modello 2005Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoLieveElettronicaNA

Bollettino

Discharged Battery Energy Diagnosis Must Be Performed: The electrical system of BMW vehicles has been subject to an ongoing development process over the last few years. This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle "discharged battery" complaints. In order to properly repair the vehicle the first time in the workshop, it is very important that the diagnostic test plans are performed to completion, with all results taken into consideration. Without performing the energy diagnosis test plan, the root cause of the discharged battery cannot be identified. This increases the chances of a repeat repair.

NHTSA · bollettino del costruttore10182619Anni modello 2005Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoLieveElettronicaNA

Bollettino

Power Reduction, FC2A82 Intake VANOS and/or FC2A87 Exhaust VANOS Camshaft Fault: The ?Service Engine Soon? (MIL) lamp is illuminated and engine power reduction is perceived. This situation can occur after driving for some time with the engine at full operating temperature. If theignition is cycled, the engine then usually performs normally.

NHTSA · bollettino del costruttore10181214Anni modello 2006Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoLieveElettronicaNA

Bollettino

Power Reduction FC2A82 Intake VANOS and/or FC2 A87 Exhaust VANOS Camshaft Fault: The "Service Engine Soon" (MIL) lamp is illuminated and engine power reduction is perceived. This situation can occur after driving for some time with the engine at full operating temperature. If the ignition is cycled the engine then usually performs normally.

NHTSA · bollettino del costruttore10175267Anni modello 2006Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoLieveElettronicaNA

Bollettino

"Erroneous CC Message "Remote control! Do not switch off the engine" is Displayed. An erroneous CC message, "Remote control!" " Do not switch off the engine" is displayed in the Central Information Display (CID). The engine can still be started, even with the CC message displayed. CAUSE: Car Access System (CAS) software error"

NHTSA · bollettino del costruttore10162431Anni modello 2006Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoLieveElettronicaNA

Bollettino

"Power Reduction, FC 2A82 Intake VANOS and/or FC 2A87 Exhaust VANOS Camshaft Faults are Stored in DME. The ""Service Engine Soon"" (MIL) lamp is illuminated and engine power reduction is perceived. This situation can occur after driving for some time with the engine at full operating temperature. If the ignition is cycled, the engine then usually performs normally. The following faults are stored in the DME: * 2A82 VANOS intake - stiff; jammed mechanically * 2A87 VANOS exhaust - stiff; jammed mechanically * 130108 VANOS intake: control fault, position not reached * 130308 VANOS exhaust: control fault, position not reached For the N54 engine, the following secondary faults may also be stored: * 120408 Charge-air pressure control, cut-out: Boost pressure accumulation blocked * 3100 Boost-pressure control, deactivation - boost-pressure buildup prohibited CAUSE The VANOS faults can be caused by an insufficient oil pressure supply to the inlet VANOS adjustment unit. To effectively move the camshafts to the target positions in the specified time and under all engine conditions, sufficient oil pressure supply to the VANOS control pistons must always be available. If engine operation requires the VANOS system to quickly advance or retard the intake or exhaust camshaft, faults may be stored if the camshaft is ""late"", or does not reach the target position. In this situation, engine power may be reduced and a check control message is displayed. The consequential fault 3100 or 120408 can also be set in the DME fault memory as well."

NHTSA · bollettino del costruttore10162416Anni modello 2006Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoLieveElettronicaNA

Bollettino

Bluetooth Connection Failures. There are various connectivity failures with the following devices: Apple iPhones Samsung S6 and the S6 Edge. Connectivity failure examples are: Call disconnection - Call is transferred back to the handset. In some instances the call is then transferred back to the vehicle. Contact List incomplete General connection failures Apple iOS software (issue started with iOS 8.3 continues with iOS 9.x and its variants) Samsung S6 and S6 Edge device firmware.

NHTSA · bollettino del costruttore10151335Anni modello 2006Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoLieveElettronicaNA

Bollettino

ISTA/P Cannot Program an E-Series N55 Replacement DME. ISTA/P fails when attempting to program a replacement DME (MEVD172) on BN2000 E-Series vehicles with the Continental HPP. Part number: 12 14 8 618 483. DME logistic error between the replacement hardware and basic software prevents correct programming with ISTA/P.

NHTSA · bollettino del costruttore10151255Anni modello 2006Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoLieveElettronicaNA

Bollettino

SI B84 03 14 February 2016 Communication Systems Technical Service This Service Information bulletin supersedes SI B84 03 14 dated October 2014. SUBJECT Bluetooth Connection Failures. There are various connectivity failures with the following devices: Apple iPhones Samsung S6 and the S6 Edge. Connectivity failure examples are: Call disconnection - Call is transferred back to the handset. In some instances the call is then transferred back to the vehicle. Contact List incomplete General connection failures CAUSE Apple iOS software (issue started with iOS 8.3 continues with iOS 9.x and its variants) Samsung S6 and S6 Edge device firmware CORRECTOPM None available at this time. We are currently working with the device manufacturer on a solution.

NHTSA · bollettino del costruttore10151119Anni modello 2006Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoLieveElettronicaNA

Bollettino

SUBJECT Audio System Speaker Testing. For audio system speaker testing there is a NED (Non Electrical Diagnosis) Test Plan available. CAUSE We previously recommended use of the Audio Test CD (ATC) from BMW. This CD has been discontinued.

NHTSA · bollettino del costruttore10151115Anni modello 2006Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoLieveElettronicaNA

Bollettino

Junction Box Pin Assignment Change. When replacing the Junction Box (fuse box) using P/N 61 14 6 978 270 or later, note that various pin assignments have changed. The following additional work procedure is necessary to properly perform this repair.

NHTSA · bollettino del costruttore10150381Anni modello 2006Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoLieveElettronicaNA

Bollettino

"CCC - ""Please Insert Navigation DVD"" Appears on CID. The navigation map DVD cannot be read or detected. The message ""Please insert navigation DVD"" appears in the CID (Central Information Display). The navigation system is inoperative. This situation may also occur when upgrading to a new navigation map. The old map is recognized but the new one is not. CAUSE Faulty DVD drive; read error due to hardening of the anti-vibration gel on the read head"

NHTSA · bollettino del costruttore10150385Anni modello 2006Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Meno recenti →

Fonti: NHTSA (Stati Uniti, pubblico dominio), Transport Canada (Open Government Licence – Canada), DVSA (Regno Unito, Open Government Licence v3.0), RappelConso e Safety Gate UE (Francia, Licence Ouverte 2.0), MLIT (Giappone, Public Data License 1.0) e MOLIT (Corea del Sud, car.go.kr).